🧮 Paper 1 non-calculator warm-up — Higher

Answer key

1. (a) 0.1 m — Method: the sloping surface is the hypotenuse and the vertical rise is the side opposite the 30° angle, so rise = 4.8 × sin 30°; then compare that rise with the limit. Working: the exact value of sin 30° is one half, so the rise = 4.8 × 1/2 = 2.4 m. The limit is 2.5 m, and 2.5 − 2.4 = 0.1. Answer: the ramp is 0.1 m below the limit. Working out the rise and stopping there gives 2.4 m, which answers a question that was not asked. Dividing by sin 30° instead of multiplying gives 4.8 ÷ 0.5 = 9.6 and then 9.6 − 2.5 = 7.1 m. Treating sine as proportional to the angle, so that sin 30° is a third of sin 90°, gives 4.8 ÷ 3 = 1.6 and then 2.5 − 1.6 = 0.9 m.
2. (d) x² − 49 — Area = length × width = (x + 7)(x − 7). Expanding: x × x = x², x × (−7) = −7x, 7 × x = 7x, 7 × (−7) = −49. The two middle terms −7x and 7x cancel, leaving x² − 49. A candidate who misremembers the difference-of-two-squares result as a sum gets x² + 49. A candidate who makes a sign error and treats both middle terms as −7x instead of cancelling gets x² − 14x − 49. A candidate who confuses area with perimeter and simply adds the length and width gets 2x.
3. (c) 1 — cos 45° = √2/2 and sin 45° = √2/2. Squaring each gives (√2/2)² = 2/4 = 1/2, so (cos 45°)² + (sin 45°)² = 1/2 + 1/2 = 1. The distractor √2 comes from adding cos 45° + sin 45° directly without squaring first (√2/2 + √2/2 = √2). The distractor 2 comes from squaring the top of the fraction, (√2)² = 2, but then dividing by 2 instead of 4 for each term, giving 1 + 1 = 2. The distractor 1/2 comes from squaring only cos 45° and forgetting to add the sin 45° term.
4. (b) (2x + 1)/(x − 3) — Factorise both the numerator and the denominator before you cancel anything. The numerator 2x² + 7x + 3 factorises to (2x + 1)(x + 3), and the denominator x² − 9 is a difference of two squares, factorising to (x − 3)(x + 3). The (x + 3) factor is common to both, so it cancels, leaving (2x + 1)/(x − 3). Writing (2x + 1)/(x + 3) comes from factorising x² − 9 as (x + 3)² instead of (x − 3)(x + 3) — a difference of two squares always has one plus and one minus bracket. Writing (2x + 3)/(x − 3) comes from mis-factorising the numerator as (2x + 3)(x + 1) and then wrongly cancelling the (x + 1) against the denominator's (x + 3) as though they were the same bracket. Writing 2x + 1 comes from cancelling the (x + 3) factor correctly but then dropping the remaining (x − 3) on the denominator altogether.
5. (d) x = 4 or x = −4 — Method: divide both sides by 2 to get x² = 16, then take the square root of both sides: x = 4 or x = −4. Distractor origins: x = 4 forgets the negative root; x = 8 comes from halving 16 instead of taking its square root; x = 16 stops at x² = 16 without ever taking the square root.
6. (b) 12 m — sin 30° = opposite ÷ hypotenuse, where the opposite side is the height (6 m) and the hypotenuse is the string. So string = height ÷ sin 30° = 6 ÷ (1/2) = 12 m. The distractor 3 m comes from multiplying by sin 30° instead of dividing (6 × 1/2 = 3). The distractor 6√3 m comes from using tan 30° = 1/√3 instead of sin 30° (6 ÷ (1/√3) = 6√3). The distractor 4√3 m comes from using cos 30° = √3/2 instead of sin 30° (6 ÷ (√3/2) = 12/√3 = 4√3).
7. (d) 2x/(x − 2) — Factorise x² − 4 as (x − 2)(x + 2) first — it's a difference of two squares. The (x + 2) in the numerator then cancels with the (x + 2) in the factorised denominator, and 6x² ÷ 3x simplifies to 2x, leaving 2x/(x − 2). Writing 2/(x − 2) comes from over-cancelling 6x² ÷ 3x as 2 instead of 2x, dropping the x that should remain. Writing 2x/(x + 2) comes from factorising x² − 4 as (x + 2)² instead of (x − 2)(x + 2), a difference of two squares always has one plus and one minus bracket. Writing 2x²/(x − 2) comes from simplifying 6x² ÷ 3x as 2x² instead of 2x, dividing the coefficients but not reducing the power of x.
8. (b) −23 — Expand two of the three brackets first: (x + 5)(x − 2) = x² + 3x − 10. Then multiply this by the remaining bracket: (2x − 1)(x² + 3x − 10) = 2x³ + 6x² − 20x − x² − 3x + 10, which simplifies to 2x³ + 5x² − 23x + 10, so the coefficient of x is −23. Writing −13 comes from a sign slip in the first expansion, combining 5x − 2x as −5x − 2x = −7x instead of +3x, which carries through to a wrong final coefficient. Writing −20 comes from forgetting to distribute the −1 across every term of x² + 3x − 10, dropping the −1 × 3x = −3x contribution. Writing 10 comes from reading off the constant term of the expansion instead of the coefficient of x.
9. (b) 3²⁰ is larger — Method: two powers with different bases and different indices can be compared once they are rewritten with a common index, which is possible whenever the indices share a factor. Working: 30 and 20 have a highest common factor of 10, so 2³⁰ = (2³)¹⁰ = 8¹⁰ and 3²⁰ = (3²)¹⁰ = 9¹⁰. Both are now tenth powers, and since 9 is larger than 8, 9¹⁰ is larger than 8¹⁰. Answer: 3²⁰ is larger. The distractors: 2³⁰ is larger comes from comparing only the indices and choosing the power with the bigger index; They are equal comes from multiplying base by index, 2 × 30 and 3 × 20, and finding 60 each time; They cannot be compared without a calculator comes from assuming that powers this large can only be ranked by evaluating them in full.
10. (c) tan 45° — Method: replace each ratio by its exact value, then compare. Working: a right-angled triangle with a 45° angle is isosceles, so its opposite and adjacent sides are equal and the tangent of 45° is exactly 1. The others are cos 30° = √3/2, about 0.87; sin 45° = √2/2, about 0.71; and cos 60° = 1/2. Answer: tan 45°, the only one of the four that reaches 1. Reading √3/2 as though it were √3, about 1.73, makes cos 30° look the largest, but the division by 2 is part of the value. Ranking by the size of the angle also fails here, because the cosine of an angle falls as the angle grows.
11. (d) x⁴ — Method: dividing two powers of the same letter subtracts the index of the divisor from the index of the term being divided. Working: six factors of x on the top and two on the bottom cancel in pairs, leaving 6 − 2 = 4 factors of x. Answer: x⁴. The distractors: x³ comes from dividing the indices, 6 ÷ 2, instead of subtracting them; x⁸ comes from adding the indices, 6 + 2, as though the powers were being multiplied; x¹² comes from multiplying the indices, 6 × 2, as though a power were being raised to a power.
12. (b) 6x + 6 — Perimeter = 2[(2x + 5) + (x − 2)] = 2(3x + 3) = 6x + 6. A candidate who adds the length and width but forgets to double for the perimeter gets 3x + 3. A candidate who makes a sign error and adds 2 instead of subtracting it before doubling gets 2[(2x + 5) + (x + 2)] = 6x + 14. A candidate who multiplies the length and width instead of adding them, confusing the perimeter formula with the area formula, and then doubles that product, gets 2(2x + 5)(x − 2) = 4x² + 2x − 20.
13. (d) 2/25 — Method: write the decimal over 100 using its two decimal places, then simplify. Working: 0.08 = 8/100 = 2/25 (dividing both numerator and denominator by 4). Answer: 2/25. The student's fraction, 8/10, comes from ignoring the zero in the tenths column and reading 0.08 as though it were 0.8; it simplifies to 4/5. 1/125 comes from writing the decimal over 1000 instead of 100, as if there were three decimal places. 25/2 comes from flipping the correct fraction upside down.
14. (c) x = −2 or x = 4 — The solutions of x² − 2x − 8 = 0 are the x-values where y = 0. From the table, y = 0 when x = −2 and when x = 4, so those are the two solutions. Distractor origins: x = −1 or x = 3 picks the pair of x-values that give equal (but non-zero) y-values instead of y = 0; x = 0 or x = −8 mixes up an x-value with its corresponding y-value; x = −2 only reads off one of the two roots and misses the other.
15. (a) x = 4 or x = −3 — Method: find two numbers that multiply to give −12 and add to give −1 — these are −4 and 3. So x² − x − 12 = (x − 4)(x + 3) = 0, giving x = 4 or x = −3. Distractor origins: x = −4 or x = 3 has the signs the wrong way round; x = 4 or x = 3 makes both roots positive, ignoring the sign of −12; x = 12 or x = −1 comes from reading off the coefficient and the constant directly instead of factorising.
16. (d) 3x² + 4x − 7 — Method: the minus sign in front of the second bracket changes the sign of every term inside it; then collect like terms. Working: removing the brackets gives 5x² + 3x − 2 − 2x² + x − 5; the squared terms give 5x² − 2x² = 3x², the x terms give 3x + x = 4x, and the number terms give −2 − 5 = −7. Answer: 3x² + 4x − 7. The distractors: 7x² + 2x + 3 comes from adding the two brackets instead of subtracting, giving 5x² + 2x², 3x − x and −2 + 5; 3x² + 2x + 3 comes from applying the minus sign to 2x² only, leaving −x and +5 unchanged so that 3x − x = 2x and −2 + 5 = 3; 3x² + 4x + 3 comes from changing the signs of the terms with letters but leaving +5 as it stood, so the number terms give −2 + 5 = 3.
17. (b) 2⁵ — Method: a power outside brackets multiplies the index of every factor inside them, and dividing powers of the same base subtracts their indices. Working: (5² × 2³)³ = 5⁶ × 2⁹ and (5³ × 2²)² = 5⁶ × 2⁴. Dividing gives 5⁶⁻⁶ × 2⁹⁻⁴, and since 5⁰ = 1 the whole expression reduces to 2⁵. Answer: 2⁵. The distractors: 2² comes from adding the outside index to each inside index instead of multiplying, which gives 5⁵ × 2⁶ over 5⁵ × 2⁴; 2¹³ comes from adding the indices of 2 when dividing, 9 + 4, instead of subtracting them; 2 comes from applying the outside power to the first factor inside each bracket only, leaving 5⁶ × 2³ over 5⁶ × 2².
18. (d) 1/4 — Method: deal with the fractional index first, then the negative sign. Working: $8^{2/3} = (\sqrt[3]{8})^2 = 2^2 = 4$. A negative index means take the reciprocal of that result, so $8^{-2/3} = \frac{1}{8^{2/3}} = \frac{1}{4}$. Answer: 1/4. A candidate who evaluates $8^{2/3}$ correctly but forgets the negative sign entirely gets 4 — they have dropped the instruction to take a reciprocal. A candidate who takes the reciprocal step but applies it as a sign change to the finished number instead of inverting it gets −4. A candidate who multiplies 8 by −2/3, treating the index as an ordinary factor rather than a power, gets −16/3.
19. (c) x = 0 or x = 3 — Method: take out the common factor 5x: 5x(x − 3) = 0, so 5x = 0 or x − 3 = 0, giving x = 0 or x = 3. Distractor origins: x = 0 or x = 15 comes from forgetting to divide the second term by the common factor 5x correctly, leaving 15 instead of 3; x = 3 loses the solution x = 0 by dividing both sides by x; x = 5 or x = 3 mistakes the coefficient 5 itself for one of the solutions.
20. (d) 636 g — Let x = 0.636363... . Since two digits repeat, multiply by 100: 100x = 63.636363... . Subtracting removes the recurring part exactly: 100x − x = 63.636363... − 0.636363... = 63, so 99x = 63, giving x = 63/99 = 7/11 kg. Converting to grams: 7/11 × 1000 = 7000/11 = 636.3636... g, which rounds to 636 g. Treating the decimal as if it terminated, writing 0.63 as 63/100 kg, gives 630 g when multiplied by 1000 — this drops the recurring part entirely. Subtracting 10x instead of x, using 100x − 10x = 90x = 63, is the wrong power of ten for a two-digit block, giving x = 63/90 = 7/10 kg, which is 700 g. A numerator slip in the subtraction, 63 − 1 = 62 instead of 63, gives x = 62/99 kg, which is 62000/99 = 626.26... g, rounding to 626 g.