⏱️ Ten-minute starters — Foundation

Answer key

1. (c) 600 centilitres — Method: changing a larger unit into a smaller one means multiplying by the conversion factor given in the question. Working: 6 × 100 = 600. Answer: 600 centilitres. The distractors: 60 centilitres comes from multiplying by 10, as if a litre held 10 centilitres; 6000 centilitres comes from multiplying by 1000, which is the number of millilitres in a litre, not centilitres; 106 centilitres comes from adding 100 and 6 instead of multiplying.
2. (c) 115 — Method: use corresponding angles to carry the 65° angle from the lower rafter up to the upper rafter, then use angles on a straight line to move to the other side of the strut. Working: the angle above the upper rafter and to the left of the strut corresponds to the given angle, so it is 65°; the angle above the upper rafter and to the right of the strut lies on a straight line with it, so it is 180 − 65 = 115. Answer: 115°. A candidate who assumes the angle stays 65° without allowing for the move from the left of the strut to the right of it gives 65. A candidate who uses 90° instead of 180°, working out 90 − 65, gets 25. A candidate who adds instead of subtracting, working out 180 + 65, gets 245.
3. (c) −2 — Method: rearrange the equation into the form y = mx + c, then read off the gradient. Working: 3y = 12 − 6x, so dividing every term by 3 gives y = 4 − 2x, so the gradient is −2. Answer: the gradient is −2. 2 comes from dropping the negative sign after dividing by 3. 4 comes from using the y-intercept, 4, instead of the gradient. −6 comes from reading off the coefficient of x before dividing the whole equation by 3.
4. (d) 4 — Method: a plane of symmetry must pass through the apex and cut the base along one of the base's own lines of symmetry. Working: a square has 4 lines of symmetry (2 through opposite edge midpoints, 2 through opposite corners), and each of these, combined with the apex, gives one plane of symmetry of the pyramid. A student who answers 2 has only found the planes through the edge midpoints, or only the ones through the corners, and missed the other pair. A student who answers 8 has doubled the correct count, perhaps confusing it with a different solid. A student who answers 1 has only spotted the one obvious front-to-back plane. Answer: 4.
5. (d) B is the reverse of A — Every component of vector B is the negative of the matching component of vector A (−2 is the negative of 2, and 5 is the negative of −5), so B undoes the translation that A performs — B is the reverse of A. 'B is the same as A' ignores that both signs have flipped. 'B is twice A' confuses a sign change with a scale-factor change; the sizes of the components have not changed, only their signs. 'B is unrelated to A in direction' misses that the two vectors are directly linked, just in opposite directions.
6. (c) 5 — The front elevation shows one square for every cube visible from the front, column by column: the left-hand column is 2 cubes high, so it contributes 2 squares; the middle column is 2 cubes high, so it contributes 2 more; the right-hand column is 1 cube high, so it contributes 1. The total is 2 + 2 + 1 = 5 squares. "6" comes from drawing a full 3 by 2 rectangle, treating every column as if it reached the greatest height. "4" comes from losing a square from one of the two tall columns, counting 2 + 1 + 1. "3" comes from counting one square per column — the width of the solid — and ignoring the heights altogether.
7. (a) 5 — Looking straight down on a row of 5 cubes standing side by side, each cube contributes exactly one square to the view from above, since the cubes do not overlap and none is hidden behind another — so the plan shows 5 squares in a row. "1" comes from treating the whole row as a single block instead of counting each cube. "10" comes from doubling the count, perhaps by also counting a front elevation's squares alongside the plan's. "25" comes from squaring the number of cubes (5 × 5) instead of counting them.
8. (c) Scalene — Method: equal angles in a triangle sit opposite equal sides, so compare the three angles with each other. Working: 10°, 58° and 112° are all different, so no two sides of the triangle are equal either, and a triangle with no equal sides is scalene. Answer: scalene. The distractors: isosceles is chosen by candidates who pair up the two acute angles, 10° and 58°, as base angles without checking that they are actually equal; equilateral is chosen by candidates who check that the three angles add to 180° and take that as meaning the triangle is regular; right-angled is chosen by candidates who see that 112° is larger than 90° and classify the triangle as containing a right angle, when in fact none of the three angles is 90°.
9. (b) 2n + 3 — Method: multiply the cost per mile by the number of miles to get an expression, then add the fixed fee as a separate term. Working: n miles at £2 each is 2n; add the £3 fixed fee: 2n + 3. Answer: 2n + 3. 3n + 2 comes from swapping the fee and the rate round, treating £3 as the rate per mile and £2 as the fixed fee. 5n comes from adding the fee and the rate together first (3 + 2 = 5) and multiplying the result by n, instead of keeping the fixed fee as its own term. 2n − 3 comes from subtracting the fixed fee instead of adding it.
10. (b) 4/5 — Write the mass of the beans over the mass of the soup: 400/500. Divide the top and bottom by 100 to get 4/5. Choosing 5/4 comes from writing the soup's mass over the beans' mass, the wrong way round. Choosing 1/5 comes from finding the difference in mass (500 − 400 = 100) and writing that over the mass of the soup, instead of using the mass of the beans. Choosing 5/9 comes from writing the mass of the soup over the total mass of both tins (500 out of 900), instead of over the mass of the beans.
11. (a) 7.5 × 10⁴ — Standard form is A × 10ⁿ, where A is between 1 and 10 (1 ≤ A < 10) and n is an integer — 7.5 × 10⁴ satisfies all of this. 12 × 10³ fails because 12 is not below 10. 0.5 × 10⁴ fails because 0.5 is not at least 1. 6.2 × 4⁵ fails because standard form always uses a power of 10, not a power of 4.
12. (a) 106° — Angle AOC and angle AOD share the arm OA and together they make up the straight line CD, so they add up to 180°: angle AOD = 180° − 74° = 106°. 74° comes from treating AOC and AOD as vertically opposite angles, which are equal — but they are adjacent angles on a straight line, not vertically opposite. 16° comes from subtracting 74° from 90°, treating the angles as complementary. 148° comes from doubling 74° instead of subtracting it from 180°.