⏱️ Ten-minute starters — Foundation

Answer key

1. (c) 28 — Method: multiply the number of whole symbols by the value of one symbol, then add the value of any half symbol shown. Working: 3 whole symbols represent 3 × 8 = 24 cars. The half symbol represents 4 cars. Total cars sold in March = 24 + 4 = 28. Leaving out the half symbol, 3 × 8 = 24, undercounts by exactly the value of that half symbol. Treating the half symbol as if it were a full symbol, 4 × 8 = 32, overcounts because it doubles the value the half symbol is worth. Giving 3.5 reports the number of symbols shown, not the number of cars they represent — the key still needs to be applied. Always apply the key to every symbol shown, including a half symbol, rather than reading off the symbol count itself.
2. (d) SAS, vertically opposite angle included — AE equals CE and BE equals DE give two pairs of equal sides, and angle AEB equals angle CED because they are vertically opposite angles formed where AC and BD cross; vertically opposite angles are always equal without needing to be measured. This included angle sits between the two known sides in each triangle, giving SAS, so 'SAS, vertically opposite angle included' is correct. 'ASA, vertically opposite angle at E' is wrong because ASA needs two pairs of equal angles with the side between them, but only one angle is known in each triangle here, and the two other known facts are sides, not angles. 'SSS, three equal side pairs' is wrong because only two pairs of sides are given; there is no third pair of equal sides. 'Cannot prove — no angle measured' is wrong because vertically opposite angles are always equal automatically when two straight lines cross, so no separate measurement is needed.
3. (b) 28 cm² — Area of a trapezium = (sum of parallel sides) ÷ 2 × height. Sum of parallel sides = 5.6 + 8.4 = 14 cm. Half of that is 14 ÷ 2 = 7 cm. Area = 7 × 4 = 28 cm². A pupil who forgets to halve gets 14 × 4 = 56 cm². A pupil who uses only the longer parallel side, as if this were a rectangle, gets 8.4 × 4 = 33.6 cm². A pupil who subtracts the parallel sides instead of adding them gets (8.4 − 5.6) ÷ 2 × 4 = 1.4 × 4 = 5.6 cm². The correct area is 28 cm².
4. (a) 10 °C — Method: work out the coldest and warmest of the four temperatures, then subtract to find the difference. Working: the coldest temperature is Sam's, −9 °C, and the warmest is Alex's, 1 °C. The difference is 1 − (−9) = 1 + 9 = 10. Answer: 10 °C. 8 °C comes from working out 1 − 9 = −8 and reporting 8, dropping the negative sign on −9 instead of turning the subtraction into an addition. 3 °C comes from comparing the wrong pair, Sam's −9 °C and Ben's −6 °C, instead of the coldest and the warmest: −6 − (−9) = 3. 7 °C comes from comparing Ben's −6 °C with Alex's 1 °C, mistakenly treating Ben's reading as the coldest instead of Sam's.
5. (b) 4.5 m² — The height ratio is 40 : 60, which simplifies to 2 : 3, so the larger bookcase is 1.5 times as tall as the smaller one. Areas scale with the square of the length scale factor, so the wood needed scales by 1.5² = 2.25. 2 × 2.25 = 4.5, so the larger bookcase needs 4.5 m² of wood. Giving 3 m² uses the length scale factor, 1.5, without squaring it (2 × 1.5 = 3). Giving 6.75 m² cubes the scale factor, 1.5³ = 3.375, as if wood coverage were a volume (2 × 3.375 = 6.75). Giving 2.25 m² is the squared scale factor on its own, without multiplying by the smaller bookcase's wood area of 2 m².
6. (c) 25 — Method: divide the larger number by its ratio part to find the value of one part, then multiply by the smaller number's ratio part. Working: 40 ÷ 8 = 5 (value of one part). Smaller number = 5 × 5 = 25. Wrong options: 64 comes from dividing by the smaller ratio part instead of the larger (40 ÷ 5 × 8); 45 comes from adding the value of one part onto 40 instead of scaling down (40 + 5); 35 comes from subtracting the value of one part from 40 (40 − 5) instead of multiplying it by the smaller ratio part.
7. (d) 6 — Method: the mode, or modal value, is the value that occurs most often in the data set, and it is a value from the data rather than a count. Working: size 4 occurs twice, size 5 occurs once, size 6 occurs three times and size 9 occurs once, so the highest frequency is three and the size it belongs to is 6. Answer: 6. The distractors: 3 comes from writing down the frequency of the most common size instead of the size itself; 9 comes from picking the largest size in the list, which confuses the mode with the maximum; 4 comes from stopping at the first size that repeats rather than checking which size repeats most often.
8. (c) 2000 mm — Put both lengths into the same unit first. There are 1000 mm in a metre, so the ribbon is 2.4 × 1000 = 2400 mm, and there are 10 mm in a centimetre, so the piece cut off is 40 × 10 = 400 mm. The length left is 2400 − 400 = 2000 mm. 2360 mm subtracts 40 mm instead of 400 mm, 200 mm works in centimetres and then labels the result as millimetres, and 2800 mm adds the piece that was cut off instead of subtracting it.
9. (a) 110° — Method: in a parallelogram the two angles at the ends of one side are co-interior angles between a pair of parallel sides, so they add up to 180°. Working: angle A + angle B = 180°, so angle B = 180° − 70° = 110°. Answer: 110°. The distractors: 70° comes from applying the rule for opposite angles of a parallelogram, which are equal, to two angles that are next to each other instead; 20° comes from treating the two angles as complementary and working out 90° − 70°; 290° comes from using the 360° angle sum of a quadrilateral and taking away only the one angle that is given, 360° − 70°.
10. (d) 9 — List all the factors of 36 in pairs that multiply to give 36: 1 × 36, 2 × 18, 3 × 12, 4 × 9, and 6 × 6. This gives the factors 1, 2, 3, 4, 6, 9, 12, 18 and 36 — nine factors in total, with 6 counted only once even though it appears in a pair with itself. Forgetting that 36 is itself a factor of 36 and leaving it off the list gives 8. Counting the number of factor pairs, five of them, rather than the number of individual factors gives 5. Treating the repeated pair 6 × 6 as two separate factors, 6 and 6 again, gives 10 instead of 9. So 36 has 9 factors.
11. (d) (0, −10) — The y-intercept occurs where x = 0. Substituting x = 0 into y = x² + 3x − 10 gives y = 0 + 0 − 10 = −10, so the graph crosses the y-axis at (0, −10). The option (0, 3) mistakenly uses the coefficient of x instead of the constant term. The option (0, 10) makes a sign error, dropping the negative from the constant term. The option (−10, 0) swaps the x- and y-coordinates, which would instead be a point on the x-axis, not the y-axis.
12. (c) 5 hours — Substitute s = 48 into the relationship: t = 240 ÷ 48 = 5 hours. Inverting the relationship, s ÷ 240 = 48 ÷ 240 = 0.2, gives 0.2 hours. Misplacing the decimal point in the division, 240 ÷ 48 read as 4.8, gives 4.8 hours. Halving the speed to 24 mph by mistake before dividing, 240 ÷ 24 = 10, gives 10 hours.