Printable · GCSE Foundation · ages 14-16
Measuring, scale drawings and bearings worksheet — GCSE Foundation
Fifteen questions on "measuring, scale drawings and bearings" — DfE statement G15. Print it, or print three versions so neighbours cannot copy by letter; the key gives the letter for each version.
Calculator
Measuring, scale drawings and bearings worksheet — GCSE Foundation
MathsUKwww.geekhero.co.uk
- 1.Two straight roads cross at a junction. The angle between them, measured with a protractor, is 118°. What is the size of the angle vertically opposite to it?
- 2.A plan of a car park is drawn to a scale of 1 : 500. A parking bay is drawn as a rectangle measuring 1.2 cm by 0.6 cm. The real width of the bay corresponds to the 0.6 cm side. What is the real width of the bay, in metres?
- 3.An angle is measured with a protractor as 47°. What type of angle is this?
- 4.A line segment is measured with a ruler and found to be 6.5 cm long. What is this length in millimetres?
- 5.A scale drawing shows a room that is 5 cm wide. The real room is 15 m wide. Write the scale of the drawing in the form 1 : n.
- 6.A scale drawing of a park uses a scale of 1 : 2000. A path is drawn 8.5 cm long on the drawing. A cyclist rides the length of the path and then rides straight back again along the same path. How far does the cyclist travel in total, in metres?
- 7.A map has a scale of 1 : 20 000. The distance between two villages is 3.4 km in real life. How long is this distance on the map, in centimetres?
- 8.The bearing of a campsite B from a walker's position A is 070°. What is the bearing of A from B?
- 9.A furniture catalogue drawing uses a scale of 1 cm to 1.5 m. A sofa in the drawing is measured as 7 cm long. What is the real length of the sofa, in metres?
- 10.A hiker walks on a bearing of 065°. She then turns clockwise through 90° and continues walking in a straight line. What bearing is she now walking on?
- 11.The angle between north and a cycle path is 40°, but it is measured anticlockwise from north. What is the three-figure bearing of the cycle path?
- 12.A garden plan is drawn to a scale of 1 cm : 1.8 m. A path on the plan measures 4.5 cm. What is the real length of the path, in metres, to 1 decimal place?
- 13.A submarine travels due south. What is the three-figure bearing for this direction?
- 14.A map has a scale of 1 : 25000. A distance between two points measures 2 cm on the map. What is the real distance, in kilometres?
- 15.A scale drawing uses a scale of 1 : 60. A path on the drawing is measured as 9.8 cm long. What is the real length of the path, in metres, to 1 decimal place?
Answer key
- (a) 118° — When two straight lines cross, the angles that are vertically opposite each other are always equal. So the angle vertically opposite 118° is also 118°. A candidate who instead finds the angle next to it on the straight line, using 180° − 118° = 62°, has found the adjacent angle, not the vertically opposite one. A candidate who answers 180° has confused the rule with angles on a straight line. A candidate who doubles the angle, giving 236°, has applied no valid angle rule at all. The vertically opposite angle is 118°.
- (b) 3 — The real width is 0.6 × 500 = 300 cm, which converts to 3 m by dividing by 100. A candidate who uses the wrong side of the rectangle, 1.2 cm, instead of the 0.6 cm width, gets 1.2 × 500 = 600 cm = 6 m. A candidate who multiplies correctly but converts the 300 cm to metres by dividing by 1000 instead of 100 gets 0.3 m. A candidate who converts by dividing by 10 instead of 100 gets 30 m. The real width of the bay is 3 m.
- (b) Acute — An acute angle is any angle less than 90°. Since 47° is less than 90°, it is acute. An obtuse angle is between 90° and 180°, which 47° is not. A reflex angle is greater than 180°, which is far too big for 47°. A right angle is exactly 90°, not 47°. The angle is acute.
- (a) 65 — There are 10 millimetres in every centimetre, so to convert from cm to mm, multiply by 10: 6.5 × 10 = 65 mm. A candidate who forgets to convert at all writes down the original number, 6.5. A candidate who multiplies by 100 instead of 10, confusing cm-to-mm with m-to-cm, gets 650. A candidate who divides by 10 instead of multiplying gets 0.65. The correct length in millimetres is 65.
- (c) 1 : 300 — First convert both lengths to the same unit: 15 m = 1500 cm. The scale compares 5 cm on the drawing to 1500 cm in real life, so dividing both parts by 5 gives a scale of 1 : 300. A candidate who compares 5 to 15 without converting units gets 1 : 3. A candidate who converts 15 m to 150 cm, using the wrong conversion factor, gets 1 : 30. A candidate who converts 15 m to 15000 cm, again using the wrong conversion factor, gets 1 : 3000. The scale of the drawing is 1 : 300.
- (b) 340 — The real length of the path is 8.5 × 2000 = 17000 cm, which converts to 170 m by dividing by 100. The cyclist rides the path there and back, so the total distance is 170 × 2 = 340 m. A candidate who forgets the return journey gives only the one-way distance, 170 m. A candidate who halves the one-way distance instead of doubling it, reading “there and back” as splitting the journey, gets 85 m. A candidate who doubles the scale factor to 4000 by mistake, getting a one-way length of 340 m, and then doubles that for the return journey, gets 680 m. The total distance the cyclist travels is 340 m.
- (a) 17 cm — Convert the real distance to centimetres first: 3.4 km = 340 000 cm. Then divide by the scale factor, 20 000, since the map is 20 000 times smaller than real life: 340 000 ÷ 20 000 = 17, so the map distance is 17 cm. Choosing 1700 cm divides by 200 instead of 20 000, losing two zeros from the scale factor (340 000 ÷ 200 = 1700). Choosing 170 cm divides by 2 000 instead of 20 000, losing one zero from the scale factor (340 000 ÷ 2 000 = 170). Choosing 0.17 cm divides by 2 000 000 instead of 20 000, adding two extra zeros to the scale factor (340 000 ÷ 2 000 000 = 0.17).
- (a) 250° — The back bearing (the bearing of A from B) differs from the bearing of B from A by exactly 180°. Because the given bearing, 070°, is less than 180°, add 180°: 070 + 180 = 250°, so the bearing of A from B is 250°. Choosing 180° assumes the back bearing is always exactly 180°, ignoring the original bearing altogether. Choosing 110° comes from subtracting 180° from 070° and dropping the negative sign (070 − 180 = −110) instead of adding 180°. Choosing 160° comes from adding only 90° instead of 180° (070 + 90 = 160).
- (b) 10.5 — Method: multiply the drawing length by the scale factor to get the real length. Working: 7 cm × 1.5 = 10.5 m. A student who answers 8.5 has added the scale factor to the drawing length instead of multiplying (7 + 1.5). A student who answers 14 has rounded the scale factor up to 2 before multiplying. A student who answers 3.5 has divided the drawing length by 2 instead of multiplying it by 1.5. Answer: 10.5 m.
- (c) 155° — Turning clockwise adds to the bearing. Starting on a bearing of 065° and turning clockwise through 90° gives 065° + 90° = 155°. A candidate who instead subtracts, working out 90° − 65° = 25°, has performed the wrong operation, giving 025°. A candidate who turns anticlockwise instead of clockwise works out 065° − 90°, which gives a negative number, and adding 360° to fix this gives 335° — the bearing for turning the other way. A candidate who thinks turning does not change the bearing at all keeps the answer as 065°. The new bearing, turning clockwise, is 155°.
- (b) 320° — A bearing is always measured clockwise from north. An angle measured anticlockwise must be converted by subtracting it from 360°: 360 − 40 = 320°, so the bearing is 320°. Choosing 040° treats the anticlockwise angle as if it were already a clockwise bearing, without converting it. Choosing 220° adds 180° to the angle, mixing this up with a back-bearing calculation (40 + 180 = 220). Choosing 400° adds the angle to 360° instead of subtracting it (40 + 360 = 400), giving a bearing greater than a full turn.
- (a) 8.1 m — Multiply the length on the plan by the scale factor: 4.5 × 1.8 = 8.1, so the real length is 8.1 m. Choosing 6.3 m adds the two numbers instead of multiplying them (4.5 + 1.8 = 6.3). Choosing 2.5 m divides the plan length by the scale factor the wrong way round (4.5 ÷ 1.8 = 2.5) instead of multiplying. Choosing 9.0 m rounds the scale factor up to 2 before multiplying (4.5 × 2 = 9.0), losing the accuracy the 1.8 was giving.
- (d) 180 — Method: bearings are measured clockwise from north and written using three figures. Working: south is a half turn (180°) clockwise from north. A student who answers 090 has confused south with east. A student who answers 270 has confused south with west. A student who answers 018 has written the correct digits in the wrong order. Answer: 180.
- (c) 0.5 — The real distance is 2 × 25000 = 50000 cm. Converting to metres, by dividing by 100, gives 500 m, and converting to kilometres, by dividing by 1000, gives 0.5 km. A candidate who divides the 50000 cm by 1000 in one go, applying the metres-to-kilometres factor straight to the centimetres, gets 50 km. A candidate who divides by 100 twice, treating 100 m as 1 km, gets 5 km. A candidate who slips one extra decimal place when converting 500 m to kilometres gets 0.05 km. The real distance is 0.5 km.
- (a) 5.9 — The real length is 9.8 × 60 = 588 cm. Converting to metres, by dividing by 100, gives 5.88 m, which rounds to 5.9 m to 1 decimal place. A candidate who rounds 5.88 down instead of up gets 5.8 m. A candidate who forgets to convert from centimetres to metres gets 58.8. A candidate who divides by 60 instead of multiplying gets 0.16, to 2 decimal places. The real length, to 1 decimal place, is 5.9 m.
Build your own mix at the worksheet builder.