Printable · GCSE Foundation · ages 14-16
Measuring, scale drawings and bearings worksheet — GCSE Foundation
Fifteen questions on "measuring, scale drawings and bearings" — DfE statement G15. Print it, or print three versions so neighbours cannot copy by letter; the key gives the letter for each version.
Non-calculator
Measuring, scale drawings and bearings worksheet — GCSE Foundation
MathsUKwww.geekhero.co.uk
- 1.A hiker walks on a bearing of 065°. She then turns clockwise through 90° and continues walking in a straight line. What bearing is she now walking on?
- 2.A scale drawing shows a room that is 5 cm wide. The real room is 15 m wide. Write the scale of the drawing in the form 1 : n.
- 3.An angle is measured with a protractor as 47°. What type of angle is this?
- 4.A furniture catalogue drawing uses a scale of 1 cm to 1.5 m. A sofa in the drawing is measured as 7 cm long. What is the real length of the sofa, in metres?
- 5.A scale drawing of a park uses a scale of 1 : 2000. A path is drawn 8.5 cm long on the drawing. A cyclist rides the length of the path and then rides straight back again along the same path. How far does the cyclist travel in total, in metres?
- 6.A map has a scale of 1 : 25000. A distance between two points measures 2 cm on the map. What is the real distance, in kilometres?
- 7.A plan of a car park is drawn to a scale of 1 : 500. A parking bay is drawn as a rectangle measuring 1.2 cm by 0.6 cm. The real width of the bay corresponds to the 0.6 cm side. What is the real width of the bay, in metres?
- 8.A line segment is measured with a ruler and found to be 6.5 cm long. What is this length in millimetres?
- 9.A hiker walks due west. What is the three-figure bearing for this direction?
- 10.The angle between north and a cycle path is 40°, but it is measured anticlockwise from north. What is the three-figure bearing of the cycle path?
- 11.A survey team measures the angle between two fences with a protractor and gets a reading of 254°. What type of angle is this?
- 12.The bearing of a campsite B from a walker's position A is 070°. What is the bearing of A from B?
- 13.The bearing of a harbour B from a ferry's position A is 260°. What is the bearing of A from B?
- 14.A submarine travels due south. What is the three-figure bearing for this direction?
- 15.A ship sails 12 km on a bearing of 070° from a harbour to a buoy. It then sails a further 9 km, still on a bearing of 070°, from the buoy to a lighthouse. How far is the lighthouse from the harbour, in kilometres?
Answer key
- (c) 155° — Turning clockwise adds to the bearing. Starting on a bearing of 065° and turning clockwise through 90° gives 065° + 90° = 155°. A candidate who instead subtracts, working out 90° − 65° = 25°, has performed the wrong operation, giving 025°. A candidate who turns anticlockwise instead of clockwise works out 065° − 90°, which gives a negative number, and adding 360° to fix this gives 335° — the bearing for turning the other way. A candidate who thinks turning does not change the bearing at all keeps the answer as 065°. The new bearing, turning clockwise, is 155°.
- (c) 1 : 300 — First convert both lengths to the same unit: 15 m = 1500 cm. The scale compares 5 cm on the drawing to 1500 cm in real life, so dividing both parts by 5 gives a scale of 1 : 300. A candidate who compares 5 to 15 without converting units gets 1 : 3. A candidate who converts 15 m to 150 cm, using the wrong conversion factor, gets 1 : 30. A candidate who converts 15 m to 15000 cm, again using the wrong conversion factor, gets 1 : 3000. The scale of the drawing is 1 : 300.
- (b) Acute — An acute angle is any angle less than 90°. Since 47° is less than 90°, it is acute. An obtuse angle is between 90° and 180°, which 47° is not. A reflex angle is greater than 180°, which is far too big for 47°. A right angle is exactly 90°, not 47°. The angle is acute.
- (b) 10.5 — Method: multiply the drawing length by the scale factor to get the real length. Working: 7 cm × 1.5 = 10.5 m. A student who answers 8.5 has added the scale factor to the drawing length instead of multiplying (7 + 1.5). A student who answers 14 has rounded the scale factor up to 2 before multiplying. A student who answers 3.5 has divided the drawing length by 2 instead of multiplying it by 1.5. Answer: 10.5 m.
- (b) 340 — The real length of the path is 8.5 × 2000 = 17000 cm, which converts to 170 m by dividing by 100. The cyclist rides the path there and back, so the total distance is 170 × 2 = 340 m. A candidate who forgets the return journey gives only the one-way distance, 170 m. A candidate who halves the one-way distance instead of doubling it, reading “there and back” as splitting the journey, gets 85 m. A candidate who doubles the scale factor to 4000 by mistake, getting a one-way length of 340 m, and then doubles that for the return journey, gets 680 m. The total distance the cyclist travels is 340 m.
- (c) 0.5 — The real distance is 2 × 25000 = 50000 cm. Converting to metres, by dividing by 100, gives 500 m, and converting to kilometres, by dividing by 1000, gives 0.5 km. A candidate who divides the 50000 cm by 1000 in one go, applying the metres-to-kilometres factor straight to the centimetres, gets 50 km. A candidate who divides by 100 twice, treating 100 m as 1 km, gets 5 km. A candidate who slips one extra decimal place when converting 500 m to kilometres gets 0.05 km. The real distance is 0.5 km.
- (b) 3 — The real width is 0.6 × 500 = 300 cm, which converts to 3 m by dividing by 100. A candidate who uses the wrong side of the rectangle, 1.2 cm, instead of the 0.6 cm width, gets 1.2 × 500 = 600 cm = 6 m. A candidate who multiplies correctly but converts the 300 cm to metres by dividing by 1000 instead of 100 gets 0.3 m. A candidate who converts by dividing by 10 instead of 100 gets 30 m. The real width of the bay is 3 m.
- (a) 65 — There are 10 millimetres in every centimetre, so to convert from cm to mm, multiply by 10: 6.5 × 10 = 65 mm. A candidate who forgets to convert at all writes down the original number, 6.5. A candidate who multiplies by 100 instead of 10, confusing cm-to-mm with m-to-cm, gets 650. A candidate who divides by 10 instead of multiplying gets 0.65. The correct length in millimetres is 65.
- (b) 270° — Bearings are measured clockwise from north (000°). Due north is 000°, due east is 090°, due south is 180° and due west is 270°. Choosing 090° gives the bearing for due east, not west. Choosing 180° gives the bearing for due south. Choosing 000° gives the bearing for due north.
- (b) 320° — A bearing is always measured clockwise from north. An angle measured anticlockwise must be converted by subtracting it from 360°: 360 − 40 = 320°, so the bearing is 320°. Choosing 040° treats the anticlockwise angle as if it were already a clockwise bearing, without converting it. Choosing 220° adds 180° to the angle, mixing this up with a back-bearing calculation (40 + 180 = 220). Choosing 400° adds the angle to 360° instead of subtracting it (40 + 360 = 400), giving a bearing greater than a full turn.
- (c) Reflex — Method: compare the measured angle to the key boundaries of 90 degrees, 180 degrees and 360 degrees. Working: 254 degrees is greater than 180 degrees but less than 360 degrees, so it lies in the reflex range. A student who answers obtuse knows the angle is bigger than 90 degrees but has not realised it is also bigger than 180 degrees; they may have worked with the smaller angle at the same point, 360 - 254 = 106 degrees, instead of the reading given. A student who answers acute has misread the scale and taken the reading as 54 degrees rather than 254 degrees. A student who answers right has guessed a commonly recognised angle type without comparing the size properly. Answer: reflex.
- (a) 250° — The back bearing (the bearing of A from B) differs from the bearing of B from A by exactly 180°. Because the given bearing, 070°, is less than 180°, add 180°: 070 + 180 = 250°, so the bearing of A from B is 250°. Choosing 180° assumes the back bearing is always exactly 180°, ignoring the original bearing altogether. Choosing 110° comes from subtracting 180° from 070° and dropping the negative sign (070 − 180 = −110) instead of adding 180°. Choosing 160° comes from adding only 90° instead of 180° (070 + 90 = 160).
- (a) 080° — The back bearing differs from the given bearing by 180°. Because 260° is greater than 180°, subtract 180°: 260 − 180 = 80°, so the bearing of A from B is 080°. Choosing 440° adds 180° instead of subtracting it, even though the result would be more than a full turn (260 + 180 = 440). Choosing 180° assumes the back bearing is always exactly 180°, ignoring the original bearing altogether. Choosing 100° comes from measuring the reflex angle the other way round the circle (360 − 260 = 100) instead of applying the 180° back-bearing rule.
- (d) 180 — Method: bearings are measured clockwise from north and written using three figures. Working: south is a half turn (180°) clockwise from north. A student who answers 090 has confused south with east. A student who answers 270 has confused south with west. A student who answers 018 has written the correct digits in the wrong order. Answer: 180.
- (b) 21 — Both legs of the journey are on the same bearing, 070°, so the ship travels in one straight line the whole way and the distances simply add: 12 + 9 = 21 km. A candidate who subtracts instead of adding gets 12 − 9 = 3 km. A candidate who multiplies the two distances gets 12 × 9 = 108. A candidate who assumes the ship changed direction and treats the two legs as the sides of a right-angled triangle works out √(12² + 9²) = √225 = 15 km — but the bearing does not change, so there is no triangle and no hypotenuse to find. Because the ship stays on one straight line, the total distance is 21 km.
Build your own mix at the worksheet builder.