Printable · GCSE Foundation · ages 14-16
Measuring, scale drawings and bearings worksheet — GCSE Foundation
Fifteen questions on "measuring, scale drawings and bearings" — DfE statement G15. Print it, or print three versions so neighbours cannot copy by letter; the key gives the letter for each version.
Non-calculator
Measuring, scale drawings and bearings worksheet — GCSE Foundation
MathsUKwww.geekhero.co.uk
- 1.A ship sails 12 km on a bearing of 070° from a harbour to a buoy. It then sails a further 9 km, still on a bearing of 070°, from the buoy to a lighthouse. How far is the lighthouse from the harbour, in kilometres?
- 2.A plan of a car park is drawn to a scale of 1 : 500. A parking bay is drawn as a rectangle measuring 1.2 cm by 0.6 cm. The real width of the bay corresponds to the 0.6 cm side. What is the real width of the bay, in metres?
- 3.A hiker walks due west. What is the three-figure bearing for this direction?
- 4.A scale drawing shows a room that is 5 cm wide. The real room is 15 m wide. Write the scale of the drawing in the form 1 : n.
- 5.The bearing of a harbour B from a ferry's position A is 260°. What is the bearing of A from B?
- 6.An angle is measured with a protractor as 47°. What type of angle is this?
- 7.The bearing of a campsite B from a walker's position A is 070°. What is the bearing of A from B?
- 8.A scale drawing of a bridge uses a scale of 1 : 25. A support beam on the drawing measures 4.4 cm. What is the real length of the beam, in metres?
- 9.A furniture catalogue drawing uses a scale of 1 cm to 1.5 m. A sofa in the drawing is measured as 7 cm long. What is the real length of the sofa, in metres?
- 10.A scale drawing of a rectangular lawn uses a scale of 1 : 125. On the drawing, the lawn measures 4 cm by 2.4 cm. Work out the perimeter of the real lawn, in metres.
- 11.The angle between north and a cycle path is 40°, but it is measured anticlockwise from north. What is the three-figure bearing of the cycle path?
- 12.A submarine travels due south. What is the three-figure bearing for this direction?
- 13.A treasure map has a scale of 1 cm to 4 m. A path from the start to a rock is drawn as two straight sections, measuring 3 cm and 2.5 cm. Work out the total real distance from the start to the rock, in metres.
- 14.A survey team measures the angle between two fences with a protractor and gets a reading of 254°. What type of angle is this?
- 15.A scale drawing of a park uses a scale of 1 : 2000. A path is drawn 8.5 cm long on the drawing. A cyclist rides the length of the path and then rides straight back again along the same path. How far does the cyclist travel in total, in metres?
Answer key
- (b) 21 — Both legs of the journey are on the same bearing, 070°, so the ship travels in one straight line the whole way and the distances simply add: 12 + 9 = 21 km. A candidate who subtracts instead of adding gets 12 − 9 = 3 km. A candidate who multiplies the two distances gets 12 × 9 = 108. A candidate who assumes the ship changed direction and treats the two legs as the sides of a right-angled triangle works out √(12² + 9²) = √225 = 15 km — but the bearing does not change, so there is no triangle and no hypotenuse to find. Because the ship stays on one straight line, the total distance is 21 km.
- (b) 3 — The real width is 0.6 × 500 = 300 cm, which converts to 3 m by dividing by 100. A candidate who uses the wrong side of the rectangle, 1.2 cm, instead of the 0.6 cm width, gets 1.2 × 500 = 600 cm = 6 m. A candidate who multiplies correctly but converts the 300 cm to metres by dividing by 1000 instead of 100 gets 0.3 m. A candidate who converts by dividing by 10 instead of 100 gets 30 m. The real width of the bay is 3 m.
- (b) 270° — Bearings are measured clockwise from north (000°). Due north is 000°, due east is 090°, due south is 180° and due west is 270°. Choosing 090° gives the bearing for due east, not west. Choosing 180° gives the bearing for due south. Choosing 000° gives the bearing for due north.
- (c) 1 : 300 — First convert both lengths to the same unit: 15 m = 1500 cm. The scale compares 5 cm on the drawing to 1500 cm in real life, so dividing both parts by 5 gives a scale of 1 : 300. A candidate who compares 5 to 15 without converting units gets 1 : 3. A candidate who converts 15 m to 150 cm, using the wrong conversion factor, gets 1 : 30. A candidate who converts 15 m to 15000 cm, again using the wrong conversion factor, gets 1 : 3000. The scale of the drawing is 1 : 300.
- (a) 080° — The back bearing differs from the given bearing by 180°. Because 260° is greater than 180°, subtract 180°: 260 − 180 = 80°, so the bearing of A from B is 080°. Choosing 440° adds 180° instead of subtracting it, even though the result would be more than a full turn (260 + 180 = 440). Choosing 180° assumes the back bearing is always exactly 180°, ignoring the original bearing altogether. Choosing 100° comes from measuring the reflex angle the other way round the circle (360 − 260 = 100) instead of applying the 180° back-bearing rule.
- (b) Acute — An acute angle is any angle less than 90°. Since 47° is less than 90°, it is acute. An obtuse angle is between 90° and 180°, which 47° is not. A reflex angle is greater than 180°, which is far too big for 47°. A right angle is exactly 90°, not 47°. The angle is acute.
- (a) 250° — The back bearing (the bearing of A from B) differs from the bearing of B from A by exactly 180°. Because the given bearing, 070°, is less than 180°, add 180°: 070 + 180 = 250°, so the bearing of A from B is 250°. Choosing 180° assumes the back bearing is always exactly 180°, ignoring the original bearing altogether. Choosing 110° comes from subtracting 180° from 070° and dropping the negative sign (070 − 180 = −110) instead of adding 180°. Choosing 160° comes from adding only 90° instead of 180° (070 + 90 = 160).
- (d) 1.1 — Method: multiply the drawing length by the scale factor to get the real length, then convert to the units asked for. Working: 4.4 cm × 25 = 110 cm = 1.1 m. A student who answers 4.4 has forgotten to use the scale at all. A student who answers 110 has correctly worked out the real length in centimetres but forgotten to convert it to metres. A student who answers 11 has used a scale factor of 2.5 instead of 25 by misreading the scale. Answer: 1.1 m.
- (b) 10.5 — Method: multiply the drawing length by the scale factor to get the real length. Working: 7 cm × 1.5 = 10.5 m. A student who answers 8.5 has added the scale factor to the drawing length instead of multiplying (7 + 1.5). A student who answers 14 has rounded the scale factor up to 2 before multiplying. A student who answers 3.5 has divided the drawing length by 2 instead of multiplying it by 1.5. Answer: 10.5 m.
- (d) 16 — Method: use the scale to find the real length and width separately, then use the perimeter formula. Working: real length = 4 cm × 125 = 500 cm = 5 m; real width = 2.4 cm × 125 = 300 cm = 3 m; perimeter = 2 × (5 + 3) = 16 m. A student who answers 8 has added the real length and width but forgotten to double the total for the perimeter. A student who answers 1600 has correctly worked out the perimeter in centimetres but forgotten to convert it to metres. A student who answers 500 has only converted the length to real centimetres and stopped there, ignoring the width and the perimeter step. Answer: 16 m.
- (b) 320° — A bearing is always measured clockwise from north. An angle measured anticlockwise must be converted by subtracting it from 360°: 360 − 40 = 320°, so the bearing is 320°. Choosing 040° treats the anticlockwise angle as if it were already a clockwise bearing, without converting it. Choosing 220° adds 180° to the angle, mixing this up with a back-bearing calculation (40 + 180 = 220). Choosing 400° adds the angle to 360° instead of subtracting it (40 + 360 = 400), giving a bearing greater than a full turn.
- (d) 180 — Method: bearings are measured clockwise from north and written using three figures. Working: south is a half turn (180°) clockwise from north. A student who answers 090 has confused south with east. A student who answers 270 has confused south with west. A student who answers 018 has written the correct digits in the wrong order. Answer: 180.
- (b) 22 — Method: add the two drawn lengths together first, then apply the scale to the total. Working: 3 cm + 2.5 cm = 5.5 cm; 5.5 cm × 4 = 22 m. A student who answers 10 has only converted one of the two sections (2.5 cm × 4) and forgotten the other. A student who answers 5.5 has added the two drawn lengths but forgotten to apply the scale at all. A student who answers 44 has doubled the correct answer, effectively applying the scale twice. Answer: 22 m.
- (c) Reflex — Method: compare the measured angle to the key boundaries of 90 degrees, 180 degrees and 360 degrees. Working: 254 degrees is greater than 180 degrees but less than 360 degrees, so it lies in the reflex range. A student who answers obtuse knows the angle is bigger than 90 degrees but has not realised it is also bigger than 180 degrees; they may have worked with the smaller angle at the same point, 360 - 254 = 106 degrees, instead of the reading given. A student who answers acute has misread the scale and taken the reading as 54 degrees rather than 254 degrees. A student who answers right has guessed a commonly recognised angle type without comparing the size properly. Answer: reflex.
- (b) 340 — The real length of the path is 8.5 × 2000 = 17000 cm, which converts to 170 m by dividing by 100. The cyclist rides the path there and back, so the total distance is 170 × 2 = 340 m. A candidate who forgets the return journey gives only the one-way distance, 170 m. A candidate who halves the one-way distance instead of doubling it, reading “there and back” as splitting the journey, gets 85 m. A candidate who doubles the scale factor to 4000 by mistake, getting a one-way length of 340 m, and then doubles that for the return journey, gets 680 m. The total distance the cyclist travels is 340 m.
Build your own mix at the worksheet builder.