Printable · GCSE Foundation · ages 14-16
Measuring, scale drawings and bearings worksheet — GCSE Foundation
Fifteen questions on "measuring, scale drawings and bearings" — DfE statement G15. Print it, or print three versions so neighbours cannot copy by letter; the key gives the letter for each version.
Measuring, scale drawings and bearings worksheet — GCSE Foundation
MathsUKwww.geekhero.co.uk
- 1.A scale drawing of a rectangular lawn uses a scale of 1 : 125. On the drawing, the lawn measures 4 cm by 2.4 cm. Work out the perimeter of the real lawn, in metres.
- 2.Two straight roads cross at a junction. The angle between them, measured with a protractor, is 118°. What is the size of the angle vertically opposite to it?
- 3.A treasure map has a scale of 1 cm to 4 m. A path from the start to a rock is drawn as two straight sections, measuring 3 cm and 2.5 cm. Work out the total real distance from the start to the rock, in metres.
- 4.A hiker walks on a bearing of 065°. She then turns clockwise through 90° and continues walking in a straight line. What bearing is she now walking on?
- 5.A hiker walks due west. What is the three-figure bearing for this direction?
- 6.An angle is measured with a protractor as 47°. What type of angle is this?
- 7.A furniture catalogue drawing uses a scale of 1 cm to 1.5 m. A sofa in the drawing is measured as 7 cm long. What is the real length of the sofa, in metres?
- 8.A hiker starts by walking on a bearing of 245°. She turns clockwise through 50°, then turns clockwise through a further 15°, and continues walking in a straight line. What bearing is she now walking on?
- 9.A scale drawing of a bridge uses a scale of 1 : 25. A support beam on the drawing measures 4.4 cm. What is the real length of the beam, in metres?
- 10.A line segment is measured with a ruler and found to be 6.5 cm long. What is this length in millimetres?
- 11.The angle between north and a footpath is 35°, measured clockwise from north. What is the three-figure bearing of the footpath?
- 12.A plan of a car park is drawn to a scale of 1 : 500. A parking bay is drawn as a rectangle measuring 1.2 cm by 0.6 cm. The real width of the bay corresponds to the 0.6 cm side. What is the real width of the bay, in metres?
- 13.A model car is built to a scale of 1 : 24. The real car is 4.32 m long. Work out the length of the model, in centimetres.
- 14.A church tower is due east of a village. What is the three-figure bearing of the church tower from the village?
- 15.The angle between north and a cycle path is 40°, but it is measured anticlockwise from north. What is the three-figure bearing of the cycle path?
Answer key
- (d) 16 — Method: use the scale to find the real length and width separately, then use the perimeter formula. Working: real length = 4 cm × 125 = 500 cm = 5 m; real width = 2.4 cm × 125 = 300 cm = 3 m; perimeter = 2 × (5 + 3) = 16 m. A student who answers 8 has added the real length and width but forgotten to double the total for the perimeter. A student who answers 1600 has correctly worked out the perimeter in centimetres but forgotten to convert it to metres. A student who answers 500 has only converted the length to real centimetres and stopped there, ignoring the width and the perimeter step. Answer: 16 m.
- (a) 118° — When two straight lines cross, the angles that are vertically opposite each other are always equal. So the angle vertically opposite 118° is also 118°. A candidate who instead finds the angle next to it on the straight line, using 180° − 118° = 62°, has found the adjacent angle, not the vertically opposite one. A candidate who answers 180° has confused the rule with angles on a straight line. A candidate who doubles the angle, giving 236°, has applied no valid angle rule at all. The vertically opposite angle is 118°.
- (b) 22 — Method: add the two drawn lengths together first, then apply the scale to the total. Working: 3 cm + 2.5 cm = 5.5 cm; 5.5 cm × 4 = 22 m. A student who answers 10 has only converted one of the two sections (2.5 cm × 4) and forgotten the other. A student who answers 5.5 has added the two drawn lengths but forgotten to apply the scale at all. A student who answers 44 has doubled the correct answer, effectively applying the scale twice. Answer: 22 m.
- (c) 155° — Turning clockwise adds to the bearing. Starting on a bearing of 065° and turning clockwise through 90° gives 065° + 90° = 155°. A candidate who instead subtracts, working out 90° − 65° = 25°, has performed the wrong operation, giving 025°. A candidate who turns anticlockwise instead of clockwise works out 065° − 90°, which gives a negative number, and adding 360° to fix this gives 335° — the bearing for turning the other way. A candidate who thinks turning does not change the bearing at all keeps the answer as 065°. The new bearing, turning clockwise, is 155°.
- (b) 270° — Bearings are measured clockwise from north (000°). Due north is 000°, due east is 090°, due south is 180° and due west is 270°. Choosing 090° gives the bearing for due east, not west. Choosing 180° gives the bearing for due south. Choosing 000° gives the bearing for due north.
- (b) Acute — An acute angle is any angle less than 90°. Since 47° is less than 90°, it is acute. An obtuse angle is between 90° and 180°, which 47° is not. A reflex angle is greater than 180°, which is far too big for 47°. A right angle is exactly 90°, not 47°. The angle is acute.
- (b) 10.5 — Method: multiply the drawing length by the scale factor to get the real length. Working: 7 cm × 1.5 = 10.5 m. A student who answers 8.5 has added the scale factor to the drawing length instead of multiplying (7 + 1.5). A student who answers 14 has rounded the scale factor up to 2 before multiplying. A student who answers 3.5 has divided the drawing length by 2 instead of multiplying it by 1.5. Answer: 10.5 m.
- (d) 310 — Method: since both turns are clockwise, add both angles to the starting bearing. Working: 245° + 50° = 295°; 295° + 15° = 310°. A student who answers 295 has only added the first turn and forgotten the second one. A student who answers 180 has subtracted both turns instead of adding them. A student who answers 320 has added the two turns as 75° instead of 65° by misreading the second turn. Answer: 310°.
- (d) 1.1 — Method: multiply the drawing length by the scale factor to get the real length, then convert to the units asked for. Working: 4.4 cm × 25 = 110 cm = 1.1 m. A student who answers 4.4 has forgotten to use the scale at all. A student who answers 110 has correctly worked out the real length in centimetres but forgotten to convert it to metres. A student who answers 11 has used a scale factor of 2.5 instead of 25 by misreading the scale. Answer: 1.1 m.
- (a) 65 — There are 10 millimetres in every centimetre, so to convert from cm to mm, multiply by 10: 6.5 × 10 = 65 mm. A candidate who forgets to convert at all writes down the original number, 6.5. A candidate who multiplies by 100 instead of 10, confusing cm-to-mm with m-to-cm, gets 650. A candidate who divides by 10 instead of multiplying gets 0.65. The correct length in millimetres is 65.
- (a) 035° — A bearing is measured clockwise from north, so an angle of 35° clockwise from north is a bearing of 035° (written with three figures). Choosing 325° measures the angle anticlockwise instead of clockwise (360 − 35 = 325). Choosing 215° adds 180° to the angle, mixing this up with a back-bearing calculation (35 + 180 = 215). Choosing 350° reorders the digits of 035, writing the ones digit before the tens digit by mistake.
- (b) 3 — The real width is 0.6 × 500 = 300 cm, which converts to 3 m by dividing by 100. A candidate who uses the wrong side of the rectangle, 1.2 cm, instead of the 0.6 cm width, gets 1.2 × 500 = 600 cm = 6 m. A candidate who multiplies correctly but converts the 300 cm to metres by dividing by 1000 instead of 100 gets 0.3 m. A candidate who converts by dividing by 10 instead of 100 gets 30 m. The real width of the bay is 3 m.
- (b) 18 — Method: convert the real length to centimetres, then divide by the scale factor to shrink it down to the model's size. Working: 4.32 m = 432 cm; 432 cm / 24 = 18 cm. A student who answers 432 has converted the units correctly but forgotten to divide by the scale factor at all. A student who answers 10368 has multiplied by the scale factor instead of dividing (432 x 24). A student who answers 1.8 has converted the metres to centimetres by multiplying by 10 instead of 100, getting 43.2 cm, and then divided by 24. Answer: 18 cm.
- (c) 090 — Method: bearings are measured clockwise from north; east is a quarter turn clockwise. Working: a quarter turn is 90°, written with a leading zero as three figures. A student who answers 009 has kept the correct digits but put the leading zero in the wrong place. A student who answers 180 has confused east with south. A student who answers 270 has confused east with west. Answer: 090.
- (b) 320° — A bearing is always measured clockwise from north. An angle measured anticlockwise must be converted by subtracting it from 360°: 360 − 40 = 320°, so the bearing is 320°. Choosing 040° treats the anticlockwise angle as if it were already a clockwise bearing, without converting it. Choosing 220° adds 180° to the angle, mixing this up with a back-bearing calculation (40 + 180 = 220). Choosing 400° adds the angle to 360° instead of subtracting it (40 + 360 = 400), giving a bearing greater than a full turn.
Build your own mix at the worksheet builder.