Printable · GCSE Foundation · ages 14-16
Measuring, scale drawings and bearings worksheet — GCSE Foundation
Fifteen questions on "measuring, scale drawings and bearings" — DfE statement G15. Print it, or print three versions so neighbours cannot copy by letter; the key gives the letter for each version.
Measuring, scale drawings and bearings worksheet — GCSE Foundation
MathsUKwww.geekhero.co.uk
- 1.A church tower is due east of a village. What is the three-figure bearing of the church tower from the village?
- 2.A plan of a school hall uses a scale of 1 : 250. A wall is drawn 3.4 cm long on the plan. Sam wants to know the wall's real length in metres. What is it?
- 3.A scale drawing of a park uses a scale of 1 : 2000. A path is drawn 8.5 cm long on the drawing. A cyclist rides the length of the path and then rides straight back again along the same path. How far does the cyclist travel in total, in metres?
- 4.A scale drawing of a bridge uses a scale of 1 : 25. A support beam on the drawing measures 4.4 cm. What is the real length of the beam, in metres?
- 5.The angle between north and a footpath is 35°, measured clockwise from north. What is the three-figure bearing of the footpath?
- 6.Two straight paths cross at a junction in a park. One of the angles between them, measured with a protractor, is 76°. What is the size of the angle immediately next to it on a straight line?
- 7.The bearing of a harbour B from a ferry's position A is 260°. What is the bearing of A from B?
- 8.A model car is built to a scale of 1 : 24. The real car is 4.32 m long. Work out the length of the model, in centimetres.
- 9.Two straight roads cross at a junction. The angle between them, measured with a protractor, is 118°. What is the size of the angle vertically opposite to it?
- 10.A scale drawing shows a room that is 5 cm wide. The real room is 15 m wide. Write the scale of the drawing in the form 1 : n.
- 11.A scale drawing of a rectangular lawn uses a scale of 1 : 125. On the drawing, the lawn measures 4 cm by 2.4 cm. Work out the perimeter of the real lawn, in metres.
- 12.A map has a scale of 1 cm : 5 km. A road is drawn 3 cm long on the map. What is the real length of the road?
- 13.A map has a scale of 1 : 25000. A distance between two points measures 2 cm on the map. What is the real distance, in kilometres?
- 14.A survey team measures the angle between two fences with a protractor and gets a reading of 254°. What type of angle is this?
- 15.The angle between north and a cycle path is 40°, but it is measured anticlockwise from north. What is the three-figure bearing of the cycle path?
Answer key
- (c) 090 — Method: bearings are measured clockwise from north; east is a quarter turn clockwise. Working: a quarter turn is 90°, written with a leading zero as three figures. A student who answers 009 has kept the correct digits but put the leading zero in the wrong place. A student who answers 180 has confused east with south. A student who answers 270 has confused east with west. Answer: 090.
- (b) 8.5 m — First apply the scale to convert the plan length to a real length in centimetres: 3.4 × 250 = 850 cm. Then convert centimetres to metres by dividing by 100: 850 ÷ 100 = 8.5, so the wall is 8.5 m long. Choosing 850 m applies the scale correctly but forgets to convert the answer from centimetres into metres. Choosing 0.85 m divides by 1000 instead of 100, confusing the centimetre-to-metre conversion with a metre-to-kilometre one. Choosing 3.4 m ignores the scale factor completely and just restates the plan length as if it were already the real length.
- (b) 340 — The real length of the path is 8.5 × 2000 = 17000 cm, which converts to 170 m by dividing by 100. The cyclist rides the path there and back, so the total distance is 170 × 2 = 340 m. A candidate who forgets the return journey gives only the one-way distance, 170 m. A candidate who halves the one-way distance instead of doubling it, reading “there and back” as splitting the journey, gets 85 m. A candidate who doubles the scale factor to 4000 by mistake, getting a one-way length of 340 m, and then doubles that for the return journey, gets 680 m. The total distance the cyclist travels is 340 m.
- (d) 1.1 — Method: multiply the drawing length by the scale factor to get the real length, then convert to the units asked for. Working: 4.4 cm × 25 = 110 cm = 1.1 m. A student who answers 4.4 has forgotten to use the scale at all. A student who answers 110 has correctly worked out the real length in centimetres but forgotten to convert it to metres. A student who answers 11 has used a scale factor of 2.5 instead of 25 by misreading the scale. Answer: 1.1 m.
- (a) 035° — A bearing is measured clockwise from north, so an angle of 35° clockwise from north is a bearing of 035° (written with three figures). Choosing 325° measures the angle anticlockwise instead of clockwise (360 − 35 = 325). Choosing 215° adds 180° to the angle, mixing this up with a back-bearing calculation (35 + 180 = 215). Choosing 350° reorders the digits of 035, writing the ones digit before the tens digit by mistake.
- (b) 104 — Method: angles on a straight line add up to 180°. Working: 180° − 76° = 104°. A student who answers 76 has mistaken this for the vertically opposite angle, which is equal, rather than the adjacent angle on a straight line. A student who answers 90 has wrongly assumed the two paths must be perpendicular. A student who answers 14 has subtracted 76° from 90° instead of from 180°. Answer: 104°.
- (a) 080° — The back bearing differs from the given bearing by 180°. Because 260° is greater than 180°, subtract 180°: 260 − 180 = 80°, so the bearing of A from B is 080°. Choosing 440° adds 180° instead of subtracting it, even though the result would be more than a full turn (260 + 180 = 440). Choosing 180° assumes the back bearing is always exactly 180°, ignoring the original bearing altogether. Choosing 100° comes from measuring the reflex angle the other way round the circle (360 − 260 = 100) instead of applying the 180° back-bearing rule.
- (b) 18 — Method: convert the real length to centimetres, then divide by the scale factor to shrink it down to the model's size. Working: 4.32 m = 432 cm; 432 cm / 24 = 18 cm. A student who answers 432 has converted the units correctly but forgotten to divide by the scale factor at all. A student who answers 10368 has multiplied by the scale factor instead of dividing (432 x 24). A student who answers 1.8 has converted the metres to centimetres by multiplying by 10 instead of 100, getting 43.2 cm, and then divided by 24. Answer: 18 cm.
- (a) 118° — When two straight lines cross, the angles that are vertically opposite each other are always equal. So the angle vertically opposite 118° is also 118°. A candidate who instead finds the angle next to it on the straight line, using 180° − 118° = 62°, has found the adjacent angle, not the vertically opposite one. A candidate who answers 180° has confused the rule with angles on a straight line. A candidate who doubles the angle, giving 236°, has applied no valid angle rule at all. The vertically opposite angle is 118°.
- (c) 1 : 300 — First convert both lengths to the same unit: 15 m = 1500 cm. The scale compares 5 cm on the drawing to 1500 cm in real life, so dividing both parts by 5 gives a scale of 1 : 300. A candidate who compares 5 to 15 without converting units gets 1 : 3. A candidate who converts 15 m to 150 cm, using the wrong conversion factor, gets 1 : 30. A candidate who converts 15 m to 15000 cm, again using the wrong conversion factor, gets 1 : 3000. The scale of the drawing is 1 : 300.
- (d) 16 — Method: use the scale to find the real length and width separately, then use the perimeter formula. Working: real length = 4 cm × 125 = 500 cm = 5 m; real width = 2.4 cm × 125 = 300 cm = 3 m; perimeter = 2 × (5 + 3) = 16 m. A student who answers 8 has added the real length and width but forgotten to double the total for the perimeter. A student who answers 1600 has correctly worked out the perimeter in centimetres but forgotten to convert it to metres. A student who answers 500 has only converted the length to real centimetres and stopped there, ignoring the width and the perimeter step. Answer: 16 m.
- (a) 15 km — Multiply the length drawn on the map by the scale: 3 × 5 = 15 km. Choosing 8 km adds the two scale numbers together (3 + 5 = 8) instead of multiplying them. Choosing 30 km comes from misreading the scale as 1 cm : 10 km and doubling the correct answer. Choosing 5 km simply repeats the scale's distance figure and ignores that the road is drawn 3 cm long, not 1 cm.
- (c) 0.5 — The real distance is 2 × 25000 = 50000 cm. Converting to metres, by dividing by 100, gives 500 m, and converting to kilometres, by dividing by 1000, gives 0.5 km. A candidate who divides the 50000 cm by 1000 in one go, applying the metres-to-kilometres factor straight to the centimetres, gets 50 km. A candidate who divides by 100 twice, treating 100 m as 1 km, gets 5 km. A candidate who slips one extra decimal place when converting 500 m to kilometres gets 0.05 km. The real distance is 0.5 km.
- (c) Reflex — Method: compare the measured angle to the key boundaries of 90 degrees, 180 degrees and 360 degrees. Working: 254 degrees is greater than 180 degrees but less than 360 degrees, so it lies in the reflex range. A student who answers obtuse knows the angle is bigger than 90 degrees but has not realised it is also bigger than 180 degrees; they may have worked with the smaller angle at the same point, 360 - 254 = 106 degrees, instead of the reading given. A student who answers acute has misread the scale and taken the reading as 54 degrees rather than 254 degrees. A student who answers right has guessed a commonly recognised angle type without comparing the size properly. Answer: reflex.
- (b) 320° — A bearing is always measured clockwise from north. An angle measured anticlockwise must be converted by subtracting it from 360°: 360 − 40 = 320°, so the bearing is 320°. Choosing 040° treats the anticlockwise angle as if it were already a clockwise bearing, without converting it. Choosing 220° adds 180° to the angle, mixing this up with a back-bearing calculation (40 + 180 = 220). Choosing 400° adds the angle to 360° instead of subtracting it (40 + 360 = 400), giving a bearing greater than a full turn.
Build your own mix at the worksheet builder.