Printable · GCSE Foundation · ages 14-16
Measuring, scale drawings and bearings worksheet — GCSE Foundation
Fifteen questions on "measuring, scale drawings and bearings" — DfE statement G15. Print it, or print three versions so neighbours cannot copy by letter; the key gives the letter for each version.
Measuring, scale drawings and bearings worksheet — GCSE Foundation
MathsUKwww.geekhero.co.uk
- 1.A scale drawing of a park uses a scale of 1 : 2000. A path is drawn 8.5 cm long on the drawing. A cyclist rides the length of the path and then rides straight back again along the same path. How far does the cyclist travel in total, in metres?
- 2.A hiker starts by walking on a bearing of 245°. She turns clockwise through 50°, then turns clockwise through a further 15°, and continues walking in a straight line. What bearing is she now walking on?
- 3.A garden plan is drawn to a scale of 1 cm : 1.8 m. A path on the plan measures 4.5 cm. What is the real length of the path, in metres, to 1 decimal place?
- 4.The angle between north and a footpath is 35°, measured clockwise from north. What is the three-figure bearing of the footpath?
- 5.A submarine travels due south. What is the three-figure bearing for this direction?
- 6.A line segment is measured with a ruler and found to be 6.5 cm long. What is this length in millimetres?
- 7.A scale drawing of a bridge uses a scale of 1 : 25. A support beam on the drawing measures 4.4 cm. What is the real length of the beam, in metres?
- 8.A church tower is due east of a village. What is the three-figure bearing of the church tower from the village?
- 9.A model car is built to a scale of 1 : 24. The real car is 4.32 m long. Work out the length of the model, in centimetres.
- 10.A map has a scale of 1 cm : 5 km. A road is drawn 3 cm long on the map. What is the real length of the road?
- 11.A treasure map has a scale of 1 cm to 4 m. A path from the start to a rock is drawn as two straight sections, measuring 3 cm and 2.5 cm. Work out the total real distance from the start to the rock, in metres.
- 12.The angle between north and a cycle path is 40°, but it is measured anticlockwise from north. What is the three-figure bearing of the cycle path?
- 13.A scale drawing shows a room that is 5 cm wide. The real room is 15 m wide. Write the scale of the drawing in the form 1 : n.
- 14.A furniture catalogue drawing uses a scale of 1 cm to 1.5 m. A sofa in the drawing is measured as 7 cm long. What is the real length of the sofa, in metres?
- 15.A ship sails 12 km on a bearing of 070° from a harbour to a buoy. It then sails a further 9 km, still on a bearing of 070°, from the buoy to a lighthouse. How far is the lighthouse from the harbour, in kilometres?
Answer key
- (b) 340 — The real length of the path is 8.5 × 2000 = 17000 cm, which converts to 170 m by dividing by 100. The cyclist rides the path there and back, so the total distance is 170 × 2 = 340 m. A candidate who forgets the return journey gives only the one-way distance, 170 m. A candidate who halves the one-way distance instead of doubling it, reading “there and back” as splitting the journey, gets 85 m. A candidate who doubles the scale factor to 4000 by mistake, getting a one-way length of 340 m, and then doubles that for the return journey, gets 680 m. The total distance the cyclist travels is 340 m.
- (d) 310 — Method: since both turns are clockwise, add both angles to the starting bearing. Working: 245° + 50° = 295°; 295° + 15° = 310°. A student who answers 295 has only added the first turn and forgotten the second one. A student who answers 180 has subtracted both turns instead of adding them. A student who answers 320 has added the two turns as 75° instead of 65° by misreading the second turn. Answer: 310°.
- (a) 8.1 m — Multiply the length on the plan by the scale factor: 4.5 × 1.8 = 8.1, so the real length is 8.1 m. Choosing 6.3 m adds the two numbers instead of multiplying them (4.5 + 1.8 = 6.3). Choosing 2.5 m divides the plan length by the scale factor the wrong way round (4.5 ÷ 1.8 = 2.5) instead of multiplying. Choosing 9.0 m rounds the scale factor up to 2 before multiplying (4.5 × 2 = 9.0), losing the accuracy the 1.8 was giving.
- (a) 035° — A bearing is measured clockwise from north, so an angle of 35° clockwise from north is a bearing of 035° (written with three figures). Choosing 325° measures the angle anticlockwise instead of clockwise (360 − 35 = 325). Choosing 215° adds 180° to the angle, mixing this up with a back-bearing calculation (35 + 180 = 215). Choosing 350° reorders the digits of 035, writing the ones digit before the tens digit by mistake.
- (d) 180 — Method: bearings are measured clockwise from north and written using three figures. Working: south is a half turn (180°) clockwise from north. A student who answers 090 has confused south with east. A student who answers 270 has confused south with west. A student who answers 018 has written the correct digits in the wrong order. Answer: 180.
- (a) 65 — There are 10 millimetres in every centimetre, so to convert from cm to mm, multiply by 10: 6.5 × 10 = 65 mm. A candidate who forgets to convert at all writes down the original number, 6.5. A candidate who multiplies by 100 instead of 10, confusing cm-to-mm with m-to-cm, gets 650. A candidate who divides by 10 instead of multiplying gets 0.65. The correct length in millimetres is 65.
- (d) 1.1 — Method: multiply the drawing length by the scale factor to get the real length, then convert to the units asked for. Working: 4.4 cm × 25 = 110 cm = 1.1 m. A student who answers 4.4 has forgotten to use the scale at all. A student who answers 110 has correctly worked out the real length in centimetres but forgotten to convert it to metres. A student who answers 11 has used a scale factor of 2.5 instead of 25 by misreading the scale. Answer: 1.1 m.
- (c) 090 — Method: bearings are measured clockwise from north; east is a quarter turn clockwise. Working: a quarter turn is 90°, written with a leading zero as three figures. A student who answers 009 has kept the correct digits but put the leading zero in the wrong place. A student who answers 180 has confused east with south. A student who answers 270 has confused east with west. Answer: 090.
- (b) 18 — Method: convert the real length to centimetres, then divide by the scale factor to shrink it down to the model's size. Working: 4.32 m = 432 cm; 432 cm / 24 = 18 cm. A student who answers 432 has converted the units correctly but forgotten to divide by the scale factor at all. A student who answers 10368 has multiplied by the scale factor instead of dividing (432 x 24). A student who answers 1.8 has converted the metres to centimetres by multiplying by 10 instead of 100, getting 43.2 cm, and then divided by 24. Answer: 18 cm.
- (a) 15 km — Multiply the length drawn on the map by the scale: 3 × 5 = 15 km. Choosing 8 km adds the two scale numbers together (3 + 5 = 8) instead of multiplying them. Choosing 30 km comes from misreading the scale as 1 cm : 10 km and doubling the correct answer. Choosing 5 km simply repeats the scale's distance figure and ignores that the road is drawn 3 cm long, not 1 cm.
- (b) 22 — Method: add the two drawn lengths together first, then apply the scale to the total. Working: 3 cm + 2.5 cm = 5.5 cm; 5.5 cm × 4 = 22 m. A student who answers 10 has only converted one of the two sections (2.5 cm × 4) and forgotten the other. A student who answers 5.5 has added the two drawn lengths but forgotten to apply the scale at all. A student who answers 44 has doubled the correct answer, effectively applying the scale twice. Answer: 22 m.
- (b) 320° — A bearing is always measured clockwise from north. An angle measured anticlockwise must be converted by subtracting it from 360°: 360 − 40 = 320°, so the bearing is 320°. Choosing 040° treats the anticlockwise angle as if it were already a clockwise bearing, without converting it. Choosing 220° adds 180° to the angle, mixing this up with a back-bearing calculation (40 + 180 = 220). Choosing 400° adds the angle to 360° instead of subtracting it (40 + 360 = 400), giving a bearing greater than a full turn.
- (c) 1 : 300 — First convert both lengths to the same unit: 15 m = 1500 cm. The scale compares 5 cm on the drawing to 1500 cm in real life, so dividing both parts by 5 gives a scale of 1 : 300. A candidate who compares 5 to 15 without converting units gets 1 : 3. A candidate who converts 15 m to 150 cm, using the wrong conversion factor, gets 1 : 30. A candidate who converts 15 m to 15000 cm, again using the wrong conversion factor, gets 1 : 3000. The scale of the drawing is 1 : 300.
- (b) 10.5 — Method: multiply the drawing length by the scale factor to get the real length. Working: 7 cm × 1.5 = 10.5 m. A student who answers 8.5 has added the scale factor to the drawing length instead of multiplying (7 + 1.5). A student who answers 14 has rounded the scale factor up to 2 before multiplying. A student who answers 3.5 has divided the drawing length by 2 instead of multiplying it by 1.5. Answer: 10.5 m.
- (b) 21 — Both legs of the journey are on the same bearing, 070°, so the ship travels in one straight line the whole way and the distances simply add: 12 + 9 = 21 km. A candidate who subtracts instead of adding gets 12 − 9 = 3 km. A candidate who multiplies the two distances gets 12 × 9 = 108. A candidate who assumes the ship changed direction and treats the two legs as the sides of a right-angled triangle works out √(12² + 9²) = √225 = 15 km — but the bearing does not change, so there is no triangle and no hypotenuse to find. Because the ship stays on one straight line, the total distance is 21 km.
Build your own mix at the worksheet builder.