Printable · GCSE Foundation · ages 14-16
Measuring, scale drawings and bearings worksheet — GCSE Foundation
Fifteen questions on "measuring, scale drawings and bearings" — DfE statement G15. Print it, or print three versions so neighbours cannot copy by letter; the key gives the letter for each version.
Measuring, scale drawings and bearings worksheet — GCSE Foundation
MathsUKwww.geekhero.co.uk
- 1.A map has a scale of 1 cm : 5 km. A road is drawn 3 cm long on the map. What is the real length of the road?
- 2.A scale drawing of a rectangular lawn uses a scale of 1 : 125. On the drawing, the lawn measures 4 cm by 2.4 cm. Work out the perimeter of the real lawn, in metres.
- 3.The bearing of a harbour B from a ferry's position A is 260°. What is the bearing of A from B?
- 4.A scale drawing uses a scale of 1 : 60. A path on the drawing is measured as 9.8 cm long. What is the real length of the path, in metres, to 1 decimal place?
- 5.A garden plan is drawn to a scale of 1 cm : 1.8 m. A path on the plan measures 4.5 cm. What is the real length of the path, in metres, to 1 decimal place?
- 6.A hiker walks due west. What is the three-figure bearing for this direction?
- 7.An angle is measured with a protractor as 47°. What type of angle is this?
- 8.A survey team measures the angle between two fences with a protractor and gets a reading of 254°. What type of angle is this?
- 9.The angle between north and a cycle path is 40°, but it is measured anticlockwise from north. What is the three-figure bearing of the cycle path?
- 10.A map has a scale of 1 : 20 000. The distance between two villages is 3.4 km in real life. How long is this distance on the map, in centimetres?
- 11.A treasure map has a scale of 1 cm to 4 m. A path from the start to a rock is drawn as two straight sections, measuring 3 cm and 2.5 cm. Work out the total real distance from the start to the rock, in metres.
- 12.A plan of a school hall uses a scale of 1 : 250. A wall is drawn 3.4 cm long on the plan. Sam wants to know the wall's real length in metres. What is it?
- 13.A bearing is described as being exactly halfway between north and east, measured clockwise. What is the three-figure bearing?
- 14.A furniture catalogue drawing uses a scale of 1 cm to 1.5 m. A sofa in the drawing is measured as 7 cm long. What is the real length of the sofa, in metres?
- 15.A scale drawing of a park uses a scale of 1 : 2000. A path is drawn 8.5 cm long on the drawing. A cyclist rides the length of the path and then rides straight back again along the same path. How far does the cyclist travel in total, in metres?
Answer key
- (a) 15 km — Multiply the length drawn on the map by the scale: 3 × 5 = 15 km. Choosing 8 km adds the two scale numbers together (3 + 5 = 8) instead of multiplying them. Choosing 30 km comes from misreading the scale as 1 cm : 10 km and doubling the correct answer. Choosing 5 km simply repeats the scale's distance figure and ignores that the road is drawn 3 cm long, not 1 cm.
- (d) 16 — Method: use the scale to find the real length and width separately, then use the perimeter formula. Working: real length = 4 cm × 125 = 500 cm = 5 m; real width = 2.4 cm × 125 = 300 cm = 3 m; perimeter = 2 × (5 + 3) = 16 m. A student who answers 8 has added the real length and width but forgotten to double the total for the perimeter. A student who answers 1600 has correctly worked out the perimeter in centimetres but forgotten to convert it to metres. A student who answers 500 has only converted the length to real centimetres and stopped there, ignoring the width and the perimeter step. Answer: 16 m.
- (a) 080° — The back bearing differs from the given bearing by 180°. Because 260° is greater than 180°, subtract 180°: 260 − 180 = 80°, so the bearing of A from B is 080°. Choosing 440° adds 180° instead of subtracting it, even though the result would be more than a full turn (260 + 180 = 440). Choosing 180° assumes the back bearing is always exactly 180°, ignoring the original bearing altogether. Choosing 100° comes from measuring the reflex angle the other way round the circle (360 − 260 = 100) instead of applying the 180° back-bearing rule.
- (a) 5.9 — The real length is 9.8 × 60 = 588 cm. Converting to metres, by dividing by 100, gives 5.88 m, which rounds to 5.9 m to 1 decimal place. A candidate who rounds 5.88 down instead of up gets 5.8 m. A candidate who forgets to convert from centimetres to metres gets 58.8. A candidate who divides by 60 instead of multiplying gets 0.16, to 2 decimal places. The real length, to 1 decimal place, is 5.9 m.
- (a) 8.1 m — Multiply the length on the plan by the scale factor: 4.5 × 1.8 = 8.1, so the real length is 8.1 m. Choosing 6.3 m adds the two numbers instead of multiplying them (4.5 + 1.8 = 6.3). Choosing 2.5 m divides the plan length by the scale factor the wrong way round (4.5 ÷ 1.8 = 2.5) instead of multiplying. Choosing 9.0 m rounds the scale factor up to 2 before multiplying (4.5 × 2 = 9.0), losing the accuracy the 1.8 was giving.
- (b) 270° — Bearings are measured clockwise from north (000°). Due north is 000°, due east is 090°, due south is 180° and due west is 270°. Choosing 090° gives the bearing for due east, not west. Choosing 180° gives the bearing for due south. Choosing 000° gives the bearing for due north.
- (b) Acute — An acute angle is any angle less than 90°. Since 47° is less than 90°, it is acute. An obtuse angle is between 90° and 180°, which 47° is not. A reflex angle is greater than 180°, which is far too big for 47°. A right angle is exactly 90°, not 47°. The angle is acute.
- (c) Reflex — Method: compare the measured angle to the key boundaries of 90 degrees, 180 degrees and 360 degrees. Working: 254 degrees is greater than 180 degrees but less than 360 degrees, so it lies in the reflex range. A student who answers obtuse knows the angle is bigger than 90 degrees but has not realised it is also bigger than 180 degrees; they may have worked with the smaller angle at the same point, 360 - 254 = 106 degrees, instead of the reading given. A student who answers acute has misread the scale and taken the reading as 54 degrees rather than 254 degrees. A student who answers right has guessed a commonly recognised angle type without comparing the size properly. Answer: reflex.
- (b) 320° — A bearing is always measured clockwise from north. An angle measured anticlockwise must be converted by subtracting it from 360°: 360 − 40 = 320°, so the bearing is 320°. Choosing 040° treats the anticlockwise angle as if it were already a clockwise bearing, without converting it. Choosing 220° adds 180° to the angle, mixing this up with a back-bearing calculation (40 + 180 = 220). Choosing 400° adds the angle to 360° instead of subtracting it (40 + 360 = 400), giving a bearing greater than a full turn.
- (a) 17 cm — Convert the real distance to centimetres first: 3.4 km = 340 000 cm. Then divide by the scale factor, 20 000, since the map is 20 000 times smaller than real life: 340 000 ÷ 20 000 = 17, so the map distance is 17 cm. Choosing 1700 cm divides by 200 instead of 20 000, losing two zeros from the scale factor (340 000 ÷ 200 = 1700). Choosing 170 cm divides by 2 000 instead of 20 000, losing one zero from the scale factor (340 000 ÷ 2 000 = 170). Choosing 0.17 cm divides by 2 000 000 instead of 20 000, adding two extra zeros to the scale factor (340 000 ÷ 2 000 000 = 0.17).
- (b) 22 — Method: add the two drawn lengths together first, then apply the scale to the total. Working: 3 cm + 2.5 cm = 5.5 cm; 5.5 cm × 4 = 22 m. A student who answers 10 has only converted one of the two sections (2.5 cm × 4) and forgotten the other. A student who answers 5.5 has added the two drawn lengths but forgotten to apply the scale at all. A student who answers 44 has doubled the correct answer, effectively applying the scale twice. Answer: 22 m.
- (b) 8.5 m — First apply the scale to convert the plan length to a real length in centimetres: 3.4 × 250 = 850 cm. Then convert centimetres to metres by dividing by 100: 850 ÷ 100 = 8.5, so the wall is 8.5 m long. Choosing 850 m applies the scale correctly but forgets to convert the answer from centimetres into metres. Choosing 0.85 m divides by 1000 instead of 100, confusing the centimetre-to-metre conversion with a metre-to-kilometre one. Choosing 3.4 m ignores the scale factor completely and just restates the plan length as if it were already the real length.
- (b) 045° — North is 000° and east is 090°; halfway between them, measured clockwise, is 045°. Choosing 090° gives east itself, not the midpoint between north and east. Choosing 135° gives the midpoint between east (090°) and south (180°) instead of between north and east. Choosing 225° is the back bearing of 045° (045° + 180°), not the bearing itself.
- (b) 10.5 — Method: multiply the drawing length by the scale factor to get the real length. Working: 7 cm × 1.5 = 10.5 m. A student who answers 8.5 has added the scale factor to the drawing length instead of multiplying (7 + 1.5). A student who answers 14 has rounded the scale factor up to 2 before multiplying. A student who answers 3.5 has divided the drawing length by 2 instead of multiplying it by 1.5. Answer: 10.5 m.
- (b) 340 — The real length of the path is 8.5 × 2000 = 17000 cm, which converts to 170 m by dividing by 100. The cyclist rides the path there and back, so the total distance is 170 × 2 = 340 m. A candidate who forgets the return journey gives only the one-way distance, 170 m. A candidate who halves the one-way distance instead of doubling it, reading “there and back” as splitting the journey, gets 85 m. A candidate who doubles the scale factor to 4000 by mistake, getting a one-way length of 340 m, and then doubles that for the return journey, gets 680 m. The total distance the cyclist travels is 340 m.
Build your own mix at the worksheet builder.