Printable · GCSE Foundation · ages 14-16
Measuring, scale drawings and bearings worksheet — GCSE Foundation
Fifteen questions on "measuring, scale drawings and bearings" — DfE statement G15. Print it, or print three versions so neighbours cannot copy by letter; the key gives the letter for each version.
Measuring, scale drawings and bearings worksheet — GCSE Foundation
MathsUKwww.geekhero.co.uk
- 1.A furniture catalogue drawing uses a scale of 1 cm to 1.5 m. A sofa in the drawing is measured as 7 cm long. What is the real length of the sofa, in metres?
- 2.A hiker walks due west. What is the three-figure bearing for this direction?
- 3.A bearing is described as being exactly halfway between north and east, measured clockwise. What is the three-figure bearing?
- 4.A scale drawing uses a scale of 1 : 60. A path on the drawing is measured as 9.8 cm long. What is the real length of the path, in metres, to 1 decimal place?
- 5.A scale drawing of a bridge uses a scale of 1 : 25. A support beam on the drawing measures 4.4 cm. What is the real length of the beam, in metres?
- 6.Two straight paths cross at a junction in a park. One of the angles between them, measured with a protractor, is 76°. What is the size of the angle immediately next to it on a straight line?
- 7.A line segment is measured with a ruler and found to be 6.5 cm long. What is this length in millimetres?
- 8.The angle between north and a footpath is 35°, measured clockwise from north. What is the three-figure bearing of the footpath?
- 9.A map has a scale of 1 : 25000. A distance between two points measures 2 cm on the map. What is the real distance, in kilometres?
- 10.A model car is built to a scale of 1 : 24. The real car is 4.32 m long. Work out the length of the model, in centimetres.
- 11.A survey team measures the angle between two fences with a protractor and gets a reading of 254°. What type of angle is this?
- 12.A plan of a school hall uses a scale of 1 : 250. A wall is drawn 3.4 cm long on the plan. Sam wants to know the wall's real length in metres. What is it?
- 13.A scale drawing shows a room that is 5 cm wide. The real room is 15 m wide. Write the scale of the drawing in the form 1 : n.
- 14.An angle is measured with a protractor as 47°. What type of angle is this?
- 15.A plan of a car park is drawn to a scale of 1 : 500. A parking bay is drawn as a rectangle measuring 1.2 cm by 0.6 cm. The real width of the bay corresponds to the 0.6 cm side. What is the real width of the bay, in metres?
Answer key
- (b) 10.5 — Method: multiply the drawing length by the scale factor to get the real length. Working: 7 cm × 1.5 = 10.5 m. A student who answers 8.5 has added the scale factor to the drawing length instead of multiplying (7 + 1.5). A student who answers 14 has rounded the scale factor up to 2 before multiplying. A student who answers 3.5 has divided the drawing length by 2 instead of multiplying it by 1.5. Answer: 10.5 m.
- (b) 270° — Bearings are measured clockwise from north (000°). Due north is 000°, due east is 090°, due south is 180° and due west is 270°. Choosing 090° gives the bearing for due east, not west. Choosing 180° gives the bearing for due south. Choosing 000° gives the bearing for due north.
- (b) 045° — North is 000° and east is 090°; halfway between them, measured clockwise, is 045°. Choosing 090° gives east itself, not the midpoint between north and east. Choosing 135° gives the midpoint between east (090°) and south (180°) instead of between north and east. Choosing 225° is the back bearing of 045° (045° + 180°), not the bearing itself.
- (a) 5.9 — The real length is 9.8 × 60 = 588 cm. Converting to metres, by dividing by 100, gives 5.88 m, which rounds to 5.9 m to 1 decimal place. A candidate who rounds 5.88 down instead of up gets 5.8 m. A candidate who forgets to convert from centimetres to metres gets 58.8. A candidate who divides by 60 instead of multiplying gets 0.16, to 2 decimal places. The real length, to 1 decimal place, is 5.9 m.
- (d) 1.1 — Method: multiply the drawing length by the scale factor to get the real length, then convert to the units asked for. Working: 4.4 cm × 25 = 110 cm = 1.1 m. A student who answers 4.4 has forgotten to use the scale at all. A student who answers 110 has correctly worked out the real length in centimetres but forgotten to convert it to metres. A student who answers 11 has used a scale factor of 2.5 instead of 25 by misreading the scale. Answer: 1.1 m.
- (b) 104 — Method: angles on a straight line add up to 180°. Working: 180° − 76° = 104°. A student who answers 76 has mistaken this for the vertically opposite angle, which is equal, rather than the adjacent angle on a straight line. A student who answers 90 has wrongly assumed the two paths must be perpendicular. A student who answers 14 has subtracted 76° from 90° instead of from 180°. Answer: 104°.
- (a) 65 — There are 10 millimetres in every centimetre, so to convert from cm to mm, multiply by 10: 6.5 × 10 = 65 mm. A candidate who forgets to convert at all writes down the original number, 6.5. A candidate who multiplies by 100 instead of 10, confusing cm-to-mm with m-to-cm, gets 650. A candidate who divides by 10 instead of multiplying gets 0.65. The correct length in millimetres is 65.
- (a) 035° — A bearing is measured clockwise from north, so an angle of 35° clockwise from north is a bearing of 035° (written with three figures). Choosing 325° measures the angle anticlockwise instead of clockwise (360 − 35 = 325). Choosing 215° adds 180° to the angle, mixing this up with a back-bearing calculation (35 + 180 = 215). Choosing 350° reorders the digits of 035, writing the ones digit before the tens digit by mistake.
- (c) 0.5 — The real distance is 2 × 25000 = 50000 cm. Converting to metres, by dividing by 100, gives 500 m, and converting to kilometres, by dividing by 1000, gives 0.5 km. A candidate who divides the 50000 cm by 1000 in one go, applying the metres-to-kilometres factor straight to the centimetres, gets 50 km. A candidate who divides by 100 twice, treating 100 m as 1 km, gets 5 km. A candidate who slips one extra decimal place when converting 500 m to kilometres gets 0.05 km. The real distance is 0.5 km.
- (b) 18 — Method: convert the real length to centimetres, then divide by the scale factor to shrink it down to the model's size. Working: 4.32 m = 432 cm; 432 cm / 24 = 18 cm. A student who answers 432 has converted the units correctly but forgotten to divide by the scale factor at all. A student who answers 10368 has multiplied by the scale factor instead of dividing (432 x 24). A student who answers 1.8 has converted the metres to centimetres by multiplying by 10 instead of 100, getting 43.2 cm, and then divided by 24. Answer: 18 cm.
- (c) Reflex — Method: compare the measured angle to the key boundaries of 90 degrees, 180 degrees and 360 degrees. Working: 254 degrees is greater than 180 degrees but less than 360 degrees, so it lies in the reflex range. A student who answers obtuse knows the angle is bigger than 90 degrees but has not realised it is also bigger than 180 degrees; they may have worked with the smaller angle at the same point, 360 - 254 = 106 degrees, instead of the reading given. A student who answers acute has misread the scale and taken the reading as 54 degrees rather than 254 degrees. A student who answers right has guessed a commonly recognised angle type without comparing the size properly. Answer: reflex.
- (b) 8.5 m — First apply the scale to convert the plan length to a real length in centimetres: 3.4 × 250 = 850 cm. Then convert centimetres to metres by dividing by 100: 850 ÷ 100 = 8.5, so the wall is 8.5 m long. Choosing 850 m applies the scale correctly but forgets to convert the answer from centimetres into metres. Choosing 0.85 m divides by 1000 instead of 100, confusing the centimetre-to-metre conversion with a metre-to-kilometre one. Choosing 3.4 m ignores the scale factor completely and just restates the plan length as if it were already the real length.
- (c) 1 : 300 — First convert both lengths to the same unit: 15 m = 1500 cm. The scale compares 5 cm on the drawing to 1500 cm in real life, so dividing both parts by 5 gives a scale of 1 : 300. A candidate who compares 5 to 15 without converting units gets 1 : 3. A candidate who converts 15 m to 150 cm, using the wrong conversion factor, gets 1 : 30. A candidate who converts 15 m to 15000 cm, again using the wrong conversion factor, gets 1 : 3000. The scale of the drawing is 1 : 300.
- (b) Acute — An acute angle is any angle less than 90°. Since 47° is less than 90°, it is acute. An obtuse angle is between 90° and 180°, which 47° is not. A reflex angle is greater than 180°, which is far too big for 47°. A right angle is exactly 90°, not 47°. The angle is acute.
- (b) 3 — The real width is 0.6 × 500 = 300 cm, which converts to 3 m by dividing by 100. A candidate who uses the wrong side of the rectangle, 1.2 cm, instead of the 0.6 cm width, gets 1.2 × 500 = 600 cm = 6 m. A candidate who multiplies correctly but converts the 300 cm to metres by dividing by 1000 instead of 100 gets 0.3 m. A candidate who converts by dividing by 10 instead of 100 gets 30 m. The real width of the bay is 3 m.
Build your own mix at the worksheet builder.