Printable · GCSE Foundation · ages 14-16
Measuring, scale drawings and bearings worksheet — GCSE Foundation
Fifteen questions on "measuring, scale drawings and bearings" — DfE statement G15. Print it, or print three versions so neighbours cannot copy by letter; the key gives the letter for each version.
Calculator
Answer key: Measuring, scale drawings and bearings worksheet — GCSE Foundation
MathsUKwww.geekhero.co.uk
- (a) 250° — The back bearing (the bearing of A from B) differs from the bearing of B from A by exactly 180°. Because the given bearing, 070°, is less than 180°, add 180°: 070 + 180 = 250°, so the bearing of A from B is 250°. Choosing 180° assumes the back bearing is always exactly 180°, ignoring the original bearing altogether. Choosing 110° comes from subtracting 180° from 070° and dropping the negative sign (070 − 180 = −110) instead of adding 180°. Choosing 160° comes from adding only 90° instead of 180° (070 + 90 = 160).
- (b) 21 — Both legs of the journey are on the same bearing, 070°, so the ship travels in one straight line the whole way and the distances simply add: 12 + 9 = 21 km. A candidate who subtracts instead of adding gets 12 − 9 = 3 km. A candidate who multiplies the two distances gets 12 × 9 = 108. A candidate who assumes the ship changed direction and treats the two legs as the sides of a right-angled triangle works out √(12² + 9²) = √225 = 15 km — but the bearing does not change, so there is no triangle and no hypotenuse to find. Because the ship stays on one straight line, the total distance is 21 km.
- (b) 3 — The real width is 0.6 × 500 = 300 cm, which converts to 3 m by dividing by 100. A candidate who uses the wrong side of the rectangle, 1.2 cm, instead of the 0.6 cm width, gets 1.2 × 500 = 600 cm = 6 m. A candidate who multiplies correctly but converts the 300 cm to metres by dividing by 1000 instead of 100 gets 0.3 m. A candidate who converts by dividing by 10 instead of 100 gets 30 m. The real width of the bay is 3 m.
- (a) 118° — When two straight lines cross, the angles that are vertically opposite each other are always equal. So the angle vertically opposite 118° is also 118°. A candidate who instead finds the angle next to it on the straight line, using 180° − 118° = 62°, has found the adjacent angle, not the vertically opposite one. A candidate who answers 180° has confused the rule with angles on a straight line. A candidate who doubles the angle, giving 236°, has applied no valid angle rule at all. The vertically opposite angle is 118°.
- (a) 5.9 — The real length is 9.8 × 60 = 588 cm. Converting to metres, by dividing by 100, gives 5.88 m, which rounds to 5.9 m to 1 decimal place. A candidate who rounds 5.88 down instead of up gets 5.8 m. A candidate who forgets to convert from centimetres to metres gets 58.8. A candidate who divides by 60 instead of multiplying gets 0.16, to 2 decimal places. The real length, to 1 decimal place, is 5.9 m.
- (a) 035° — A bearing is measured clockwise from north, so an angle of 35° clockwise from north is a bearing of 035° (written with three figures). Choosing 325° measures the angle anticlockwise instead of clockwise (360 − 35 = 325). Choosing 215° adds 180° to the angle, mixing this up with a back-bearing calculation (35 + 180 = 215). Choosing 350° reorders the digits of 035, writing the ones digit before the tens digit by mistake.
- (a) 8.1 m — Multiply the length on the plan by the scale factor: 4.5 × 1.8 = 8.1, so the real length is 8.1 m. Choosing 6.3 m adds the two numbers instead of multiplying them (4.5 + 1.8 = 6.3). Choosing 2.5 m divides the plan length by the scale factor the wrong way round (4.5 ÷ 1.8 = 2.5) instead of multiplying. Choosing 9.0 m rounds the scale factor up to 2 before multiplying (4.5 × 2 = 9.0), losing the accuracy the 1.8 was giving.
- (c) 155° — Turning clockwise adds to the bearing. Starting on a bearing of 065° and turning clockwise through 90° gives 065° + 90° = 155°. A candidate who instead subtracts, working out 90° − 65° = 25°, has performed the wrong operation, giving 025°. A candidate who turns anticlockwise instead of clockwise works out 065° − 90°, which gives a negative number, and adding 360° to fix this gives 335° — the bearing for turning the other way. A candidate who thinks turning does not change the bearing at all keeps the answer as 065°. The new bearing, turning clockwise, is 155°.
- (a) 65 — There are 10 millimetres in every centimetre, so to convert from cm to mm, multiply by 10: 6.5 × 10 = 65 mm. A candidate who forgets to convert at all writes down the original number, 6.5. A candidate who multiplies by 100 instead of 10, confusing cm-to-mm with m-to-cm, gets 650. A candidate who divides by 10 instead of multiplying gets 0.65. The correct length in millimetres is 65.
- (b) 18 — Method: convert the real length to centimetres, then divide by the scale factor to shrink it down to the model's size. Working: 4.32 m = 432 cm; 432 cm / 24 = 18 cm. A student who answers 432 has converted the units correctly but forgotten to divide by the scale factor at all. A student who answers 10368 has multiplied by the scale factor instead of dividing (432 x 24). A student who answers 1.8 has converted the metres to centimetres by multiplying by 10 instead of 100, getting 43.2 cm, and then divided by 24. Answer: 18 cm.
- (c) 0.5 — The real distance is 2 × 25000 = 50000 cm. Converting to metres, by dividing by 100, gives 500 m, and converting to kilometres, by dividing by 1000, gives 0.5 km. A candidate who divides the 50000 cm by 1000 in one go, applying the metres-to-kilometres factor straight to the centimetres, gets 50 km. A candidate who divides by 100 twice, treating 100 m as 1 km, gets 5 km. A candidate who slips one extra decimal place when converting 500 m to kilometres gets 0.05 km. The real distance is 0.5 km.
- (b) 10.5 — Method: multiply the drawing length by the scale factor to get the real length. Working: 7 cm × 1.5 = 10.5 m. A student who answers 8.5 has added the scale factor to the drawing length instead of multiplying (7 + 1.5). A student who answers 14 has rounded the scale factor up to 2 before multiplying. A student who answers 3.5 has divided the drawing length by 2 instead of multiplying it by 1.5. Answer: 10.5 m.
- (a) 080° — The back bearing differs from the given bearing by 180°. Because 260° is greater than 180°, subtract 180°: 260 − 180 = 80°, so the bearing of A from B is 080°. Choosing 440° adds 180° instead of subtracting it, even though the result would be more than a full turn (260 + 180 = 440). Choosing 180° assumes the back bearing is always exactly 180°, ignoring the original bearing altogether. Choosing 100° comes from measuring the reflex angle the other way round the circle (360 − 260 = 100) instead of applying the 180° back-bearing rule.
- (c) 090 — Method: bearings are measured clockwise from north; east is a quarter turn clockwise. Working: a quarter turn is 90°, written with a leading zero as three figures. A student who answers 009 has kept the correct digits but put the leading zero in the wrong place. A student who answers 180 has confused east with south. A student who answers 270 has confused east with west. Answer: 090.
- (b) Acute — An acute angle is any angle less than 90°. Since 47° is less than 90°, it is acute. An obtuse angle is between 90° and 180°, which 47° is not. A reflex angle is greater than 180°, which is far too big for 47°. A right angle is exactly 90°, not 47°. The angle is acute.
Build your own mix at the worksheet builder.