Printable · GCSE Foundation · ages 14-16
Geometry and measures worksheet — GCSE Foundation
Fifteen questions across the geometry and measures statements at Foundation tier. Choose the non-calculator filter to rehearse Paper 1, which counts for a third of the marks.
Non-calculator
Geometry and measures worksheet — GCSE Foundation
MathsUKwww.geekhero.co.uk
- 1.Write down which one of these quadrilaterals always has diagonals that are equal in length and that cross at right angles.
- 2.Work out the distance between the point (0, 0) and the point (5, 12).
- 3.Two straight paths cross at a junction in a park. One of the angles between them, measured with a protractor, is 76°. What is the size of the angle immediately next to it on a straight line?
- 4.A water tank is a cube with edges of length 2 m. Work out how many cubic centimetres the tank holds when it is full.
- 5.Rectangle ABCD has vertices A(−1, 2), B(4, 2), C(4, 5) and D(−1, 5). The rectangle is translated so that C moves to (0, −1). Write down the coordinates of the image of A.
- 6.In kite WXYZ, WX = WZ and XY = ZY (so at each of X and Z, one side from each of the two unequal pairs meets). Angle X = 100°. Work out angle Z.
- 7.How many vertices does a cylinder have?
- 8.A children's slide is built as a right-angled triangle: the vertical ladder side is 2.4 m, the horizontal base along the ground is 3.2 m, and the sloping slide is the third side. Work out the exact length of the sloping slide.
- 9.In a construction, a point P is marked at the foot of the perpendicular drawn from point X to a straight line. Which statement correctly compares the distance XP with the distance from X to any other point on the line?
- 10.A cone is cut by a flat plane parallel to its circular base, partway up between the base and the apex. What shape is the cross-section?
- 11.After a translation by the vector , a point lands on (4, 1). Write down the coordinates of the point before the translation.
- 12.A student says the reverse of the translation vector is . Write down the correct reverse translation vector.
- 13.To construct a perpendicular to a line at a given point P on the line, compasses are first opened to draw two arcs crossing the line, one on each side of P. What is the correct next step?
- 14.A shape is translated by the vector . The point P(6, 1) lies on the shape. Write down the coordinates of the image of P.
- 15.A roof truss has two horizontal parallel rafters, one above the other. A straight strut crosses both rafters. Where the strut crosses the lower rafter, the angle above the rafter and to the left of the strut is 65°. Work out the size of the angle above the upper rafter and to the right of the strut, where the strut crosses it.
Answer key
- (a) Square — Method: two conditions are being asked for at once, so test each shape against both — the two diagonals must always be the same length as each other, and they must always meet at 90°. Working: in a rectangle the diagonals are equal but they meet at 90° only in the special case where the rectangle is also a rhombus; in a rhombus the diagonals do meet at 90° but they are of different lengths unless the rhombus is also a rectangle; the shape that satisfies both conditions for every example of it is the one that is both, and its diagonals are equal and perpendicular. Answer: the square. The distractors: the rectangle is where a candidate stops who tests only the equal-length condition and never checks the angle at the crossing; the rhombus is where a candidate stops who tests only the right-angle condition and never checks the two lengths; the parallelogram is chosen by a candidate who remembers that the diagonals of a parallelogram bisect each other and treats bisecting each other as being equal to each other, which is a different property.
- (b) 13 — Method: the straight-line distance between two points on a grid is the hypotenuse of a right-angled triangle whose shorter sides are the horizontal gap and the vertical gap between them, so Pythagoras' theorem applies. Working: one point is the origin, so the horizontal gap is 5 and the vertical gap is 12. Then d² = 5² + 12² = 25 + 144 = 169, so d = √169 = 13. Answer: 13. The distractors: 17 comes from adding the two gaps, 5 + 12, instead of adding their squares and taking the root; 12 comes from reading off the vertical gap alone and offering that as the whole distance; 7 comes from subtracting the gaps, 12 − 5, as though a distance were a difference.
- (b) 104 — Method: angles on a straight line add up to 180°. Working: 180° − 76° = 104°. A student who answers 76 has mistaken this for the vertically opposite angle, which is equal, rather than the adjacent angle on a straight line. A student who answers 90 has wrongly assumed the two paths must be perpendicular. A student who answers 14 has subtracted 76° from 90° instead of from 180°. Answer: 104°.
- (a) 8,000,000 cm³ — Method: change the edge length into centimetres first and then cube it, because 1 m = 100 cm and a volume needs that conversion applied to all three dimensions. Working: 2 m = 2 × 100 = 200 cm, so the volume is 200 × 200 × 200. 200 × 200 = 40,000 and 40,000 × 200 = 8,000,000. Answer: 8,000,000 cm³. The distractors: 8,000 cm³ comes from converting 2 m to 20 cm and cubing that; 80,000 cm³ comes from cubing in metres to get 8 m³ and then multiplying by 10,000, the conversion factor for an area rather than the 1,000,000 a volume needs; 8 cm³ comes from cubing the 2 without converting at all and simply writing cm³ because the question asked for that unit.
- (d) (−5, −4) — Method: every vertex of a translated shape moves by the same vector, so find that vector from the one vertex whose image is given, then apply it to A. Working: C(4, 5) moves to (0, −1), so across 0 − 4 = −4 and up −1 − 5 = −6, giving the vector $\binom{-4}{-6}$. Applying it to A(−1, 2): −1 − 4 = −5 and 2 − 6 = −4. Answer: the image of A is (−5, −4). Working the vector out as object minus image gives 4 to the right and 6 up, which applied to A gives (3, 8). Getting the horizontal movement right but reversing the vertical one gives (−5, 8). Treating (0, −1) as the image of every vertex ignores that a translation carries each vertex to a different place.
- (a) 100° — In a kite, the pair of angles between the unequal sides are equal to each other. Angle X and angle Z are both between one side from the WX/WZ pair and one side from the XY/ZY pair, so angle Z = angle X = 100°.
- (d) 0 — A vertex is a sharp corner point where edges meet. A cylinder has two curved, circular edges but no sharp corner points at all, so it has 0 vertices, making that the correct answer. '2' wrongly treats the two circular edges themselves as vertices, but an edge is not the same as a vertex. '4' overcounts by treating each circular edge as if it had two end-vertices, which does not apply to a continuous curved edge. '1' wrongly imagines the curved surface itself forming a single corner point, which it does not.
- (d) 4 m — The sloping slide is the hypotenuse of a right-angled triangle with the other two sides 2.4 m and 3.2 m. By Pythagoras' Theorem, hypotenuse² = 2.4² + 3.2² = 5.76 + 10.24 = 16. Square root: √16 = 4 m. Adding the two sides instead of squaring them gives 2.4 + 3.2 = 5.6 m. Truncating each squared side to a whole number before adding (5.76 to 5 and 10.24 to 10) gives √15 ≈ 3.87 m. Forgetting to take the square root and leaving the sum of the squares as the answer gives 5.76 + 10.24 = 16, written as 16 m.
- (d) XP is the shortest distance from X to the line — The perpendicular from a point to a line always gives the shortest possible distance to that line — joining X to any other point on the line forms the hypotenuse of a right-angled triangle with XP as one of the shorter sides, and a hypotenuse is always longer than either of the other two sides. So XP is shorter than the distance to every other point on the line. "XP is the longest distance from X to the line" reverses this relationship. "XP equals every other distance from X to the line" would only be true if X were equidistant from every point on the line, which is impossible for a point and a straight line. "XP cannot be compared without knowing the line's length" is false — the shortest-distance fact holds whatever the line's length, since only the local right angle matters.
- (a) A smaller circle — Since the cutting plane is parallel to the circular base, the cross-section is also a circle, but smaller than the base because the cone narrows as it rises towards the apex, so 'a smaller circle' is correct. 'A triangle' wrongly describes the outline seen from the side of the cone, not a horizontal cross-section. 'An ellipse' would only result from a cut made at an angle to the base, not one parallel to it. 'The same size circle as the base' wrongly ignores that the cone tapers, so any parallel cross-section above the base must be smaller.
- (c) (6, −5) — Method: the translation has already happened, so it must be undone: reverse the vector and apply the reverse to the point that is given. Working: reversing $\binom{-2}{6}$ gives $\binom{2}{-6}$, so the x-coordinate is 4 + 2 = 6 and the y-coordinate is 1 − 6 = −5. Check: from (6, −5) the given vector gives 6 − 2 = 4 and −5 + 6 = 1, which is the point named in the question. Answer: (6, −5). Applying the vector forwards instead of backwards gives (2, 7). Reversing the horizontal movement but not the vertical one gives (6, 7), and reversing the vertical movement but not the horizontal one gives (2, −5).
- (c) $\binom{-4}{9}$ — The reverse of a translation negates both components, so the reverse of $\binom{4}{-9}$ is $\binom{-4}{9}$. $\binom{4}{9}$ is the student's mistake — only the bottom number has been negated, and the top number was left unchanged. $\binom{-4}{-9}$ makes the opposite error, negating only the top number. $\binom{4}{-9}$ is simply the original vector, unchanged.
- (b) Draw wider arcs from each crossing point, meeting above. — Once the two arcs cross the line at points either side of P, compasses are opened to a radius greater than before and arcs are drawn from each of those two points so that they meet above (or below) the line; joining that meeting point to P gives the perpendicular. (Joining the two crossing points with a straight line only retraces part of the original line, since both points already lie on it; drawing a circle centred at P through both crossing points does not locate any new point needed for the perpendicular; drawing an arc centred at P through only one crossing point repeats the first step instead of moving on to the second pair of arcs.)
- (b) (3, 5) — Method: add the top number of the vector to the x-coordinate and the bottom number to the y-coordinate. Working: adding −3 to the x-coordinate is 6 − 3 = 3, and adding 4 to the y-coordinate is 1 + 4 = 5. Answer: the image of P is (3, 5). Subtracting the vector instead of adding it reverses the translation and gives (9, −3). Adding the top number but subtracting the bottom one, on the assumption that the lower entry always means downwards, gives (3, −3); the minus sign in a vector has already recorded the direction. Reading the two numbers the wrong way round, so that the shape moves 4 across and 3 down, gives (10, −2).
- (c) 115 — Method: use corresponding angles to carry the 65° angle from the lower rafter up to the upper rafter, then use angles on a straight line to move to the other side of the strut. Working: the angle above the upper rafter and to the left of the strut corresponds to the given angle, so it is 65°; the angle above the upper rafter and to the right of the strut lies on a straight line with it, so it is 180 − 65 = 115. Answer: 115°. A candidate who assumes the angle stays 65° without allowing for the move from the left of the strut to the right of it gives 65. A candidate who uses 90° instead of 180°, working out 90 − 65, gets 25. A candidate who adds instead of subtracting, working out 180 + 65, gets 245.
Build your own mix at the worksheet builder.