Printable · GCSE Foundation · ages 14-16
Geometry and measures worksheet — GCSE Foundation
Fifteen questions across the geometry and measures statements at Foundation tier. Choose the non-calculator filter to rehearse Paper 1, which counts for a third of the marks.
Geometry and measures worksheet — GCSE Foundation
MathsUKwww.geekhero.co.uk
- 1.Triangle T has a vertex at (8, 4). It is enlarged by a scale factor of 1/2, centre (2, 4). Work out the coordinates of the image of this vertex.
- 2.A pop-up canopy has two sloping supports that meet at the top. Each support makes an angle of 30° with the ground and is 6 m long. Using the exact value of cos 30°, work out the total width of the canopy's base.
- 3.A right-angled triangle has a hypotenuse of 14 cm. One of the other angles is 30°. Work out the exact length of the side opposite the 30° angle.
- 4.Four angles meet at a point. Three of them measure 82°, 105° and 96°. Work out the size of the fourth angle.
- 5.A crane's hook starts at the point (3.4, 9.5) on a construction site plan measured in metres. It moves along the vector to pick up a beam, then along the vector to place it. Work out the single column vector that describes the hook's overall movement from its start position to where it places the beam.
- 6.A sector of a circle has radius 8 cm and takes up three-quarters of the full circle. Work out the perimeter of the sector, in terms of π.
- 7.The vector describes a translation. A student writes it as by mistake. Write down what error the student has made.
- 8.A hexagonal prism lies on a table. A flat cut is made straight across it, at right angles to its length (so the cut is parallel to the two identical end faces). What shape is the cross-section?
- 9.Two angles lie on a straight line. One angle is 37°. Work out the size of the other angle.
- 10.Vector A is and vector B is . Write down how vector B compares to vector A.
- 11.A water tank holds 2.5 m³. Work out this volume in cm³.
- 12.A roof truss is shaped like an isosceles triangle resting on a horizontal ceiling joist. The truss's sloping edges are equal in length, and the angle at its apex is 40°. The ceiling joist continues in a straight line beyond the foot of the truss. Work out the angle between the truss's sloping edge and the extended joist, on the outside of the truss.
- 13.A ramp is built from two straight metal supports that rest on the flat ground and meet each other at the top, forming a triangle with the ground. One support meets the ground at 34°. The angle between the two supports where they meet is 71°. Work out the angle between the second support and the ground.
- 14.Which of the following correctly describes what it means for two lines to be perpendicular?
- 15.A ramp's sloped surface crosses two horizontal parallel rails. At the top rail, the angle between the ramp and the rail on the right of the ramp is (3x + 10)°. At the bottom rail, the angle between the ramp and the rail on the left of the ramp is (5x − 30)°. Work out the value of x.
Answer key
- (a) (5, 4) — Method: find the vector from the centre to the point, multiply it by the scale factor, then add the result back to the centre. Working: the vector from (2, 4) to (8, 4) is (6, 0); multiplying by 1/2 gives (3, 0); adding this to the centre (2, 4) gives (5, 4). Options: (4, 2) comes from multiplying the original coordinates by 1/2 directly, ignoring the centre of enlargement; (14, 4) comes from using a scale factor of 2 instead of 1/2, giving (2, 4) + 2×(6, 0) = (14, 4); (8, 2) comes from halving only the y-coordinate and leaving the x-coordinate unchanged. Answer: (5, 4).
- (b) 6√3 m — The horizontal distance covered by one support is adjacent to the 30° angle, so it equals 6 × cos 30° = 6 × √3/2 = 3√3 m. The total base width is made up of both supports, so it is 2 × 3√3 = 6√3 m. '3√3 m' gives only one support's horizontal distance and forgets to double it for the total width. '6 m' comes from using sin 30° instead of cos 30° for the horizontal distance (6 × sin 30° = 3, doubled to 6). '12 m' comes from doubling the full sloping length of 6 m without using any trigonometry at all.
- (b) 7 cm — The side opposite the 30° angle is found using sin 30° = opposite/hypotenuse, so opposite = 14 × sin 30° = 14 × 1/2 = 7 cm. 7√3 cm comes from using cos 30° = √3/2 instead of sin 30° (mixing up the opposite and adjacent sides). 14/√3 cm comes from using tan 30° = 1/√3 instead of sin 30°. 28 cm comes from dividing 14 by sin 30° instead of multiplying by it.
- (d) 77 — Method: angles that meet at a point add up to 360°. Working: 82 + 105 + 96 = 283; 360 − 283 = 77. Answer: 77°. A candidate who gives the sum of the three known angles and forgets to subtract it from 360° gets 283. A candidate who leaves out the 105° angle, working out 360 − 82 − 96, gets 182. A candidate who leaves out the 82° angle, working out 360 − 105 − 96, gets 159.
- (b) $\binom{-0.4}{-7}$ — The overall movement is the sum of the two vectors: (−1.2 + 0.8, −4.5 + (−2.5)) = (−0.4, −7). '$\binom{-2}{-2}$' comes from subtracting the second vector from the first instead of adding them. '$\binom{-0.4}{7}$' gets the top number right but drops the negative sign on the bottom number. '$\binom{2}{-7}$' comes from treating −1.2 + 0.8 as if the signs did not matter, giving +2 instead of −0.4.
- (a) 12π + 16 cm — A three-quarter sector's perimeter is the curved arc plus the two straight radii that close the shape. The full circumference is 2 × π × 8 = 16π cm, and three-quarters of that is 12π cm. Adding the two straight radii, 8 cm each, gives 12π + 16 cm. Leaving out the straight edges gives just 12π cm. Using one-quarter of the circumference, the piece left over rather than the piece asked for, gives 4π + 16 cm. Adding only one radius instead of two gives 12π + 8 cm.
- (c) Swapped the x and y components — The student's vector has the same two numbers, 5 and −2, but in swapped positions, so the error is swapping the x and y components rather than an error with signs or size. 'Reversed both signs' is wrong because the numbers 5 and −2 have not changed sign, only position. 'Reversed only the y sign' is wrong for the same reason — no sign has actually changed. 'Doubled the x component' is wrong because neither number has changed in size.
- (b) Hexagon — Cutting straight across a prism, at right angles to its length, always gives a cross-section that is the same shape as its end faces. The end faces of a hexagonal prism are hexagons (6-sided), so the cross-section is a hexagon. Choosing Pentagon comes from miscounting the sides of the hexagonal end as five instead of six. Choosing Rectangle comes from cutting along the LENGTH of the prism instead of across it, which gives a rectangular face, not the cross-section asked for. Choosing Triangle comes from confusing a hexagonal prism with a triangular prism.
- (a) 143° — Angles on a straight line add up to 180°. Set up 37° + x = 180°. Subtract: x = 180° − 37° = 143°. 53° comes from using 90° as the total, as if the two angles made a right angle, instead of the 180° of a straight line.
- (d) B is the reverse of A — Every component of vector B is the negative of the matching component of vector A (−2 is the negative of 2, and 5 is the negative of −5), so B undoes the translation that A performs — B is the reverse of A. 'B is the same as A' ignores that both signs have flipped. 'B is twice A' confuses a sign change with a scale-factor change; the sizes of the components have not changed, only their signs. 'B is unrelated to A in direction' misses that the two vectors are directly linked, just in opposite directions.
- (b) 2 500 000 cm³ — Method: a volume conversion uses the length factor three times, once for each dimension. Working: 1 m = 100 cm, so a cube of side 1 m is a cube of side 100 cm, and 100 × 100 × 100 = 1 000 000, giving 1 m³ = 1 000 000 cm³. Then 2.5 × 1 000 000 = 2 500 000. Answer: 2 500 000 cm³. Using the plain length factor 100 gives 250 cm³. Using 1000, which is the factor that turns cubic metres into litres, gives 2500 cm³. Using 10 000, which is the factor that belongs to square metres and square centimetres, gives 25 000 cm³.
- (a) 110° — The truss is isosceles, so its two base angles are equal; since the three angles of the triangle add up to 180° and the apex is 40°, each base angle is (180 − 40) ÷ 2 = 70°. The angle between the sloping edge and the joist, extended beyond the base of the truss, sits on a straight line with that 70° base angle, and angles on a straight line add up to 180°, so the required angle is 180 − 70 = 110°. "70°" comes from stopping after finding the base angle and giving it directly, without also using the straight-line fact to find the angle on the OUTSIDE of the truss. "140°" comes from doubling the base angle instead of using the straight-line fact. "20°" comes from taking half of the apex angle (40° ÷ 2), mistaking it for the required angle instead of properly using the triangle's angle sum.
- (a) 75° — The three angles in the triangle formed by the two supports and the ground add up to 180°. Two of the angles are 34° and 71°, so the third angle is 180 − 34 − 71 = 75, which is 75°. 105° comes from adding the two given angles together instead of subtracting them from 180° (34 + 71 = 105). 146° comes from computing 180 − 34 = 146 and forgetting to also subtract 71°. 37° comes from subtracting the two given angles from each other instead of using the triangle's angle sum (71 − 34 = 37).
- (d) Two lines that cross at right angles — Perpendicular lines are defined as two lines that cross at right angles (90°), so 'two lines that cross at right angles' is correct. 'Two lines that never meet' describes parallel lines, not perpendicular lines, so it is wrong. 'Two lines equal in length' confuses perpendicularity with two lines being the same length, which has nothing to do with the angle between them, so it is wrong. 'Two lines crossing at any angle' is too general, since crossing lines are simply called intersecting unless that angle is specifically 90°, so it is wrong.
- (d) 20 — Alternate angles between parallel lines are equal, so 3x + 10 = 5x − 30. Rearranging, 10 + 30 = 5x − 3x, so 40 = 2x, and x = 20. −10 comes from a sign error when rearranging, moving a term to the wrong side and getting −20 = 2x instead. 25 comes from wrongly treating the two angles as co-interior and adding them to 180°: (3x + 10) + (5x − 30) = 180 gives 8x − 20 = 180, so x = 25. 47.5 makes the same co-interior mistake but sets the sum equal to 360° instead of 180°, giving 8x − 20 = 360 and x = 47.5.
Build your own mix at the worksheet builder.