Printable · GCSE Foundation · ages 14-16
Geometry and measures worksheet — GCSE Foundation
Fifteen questions across the geometry and measures statements at Foundation tier. Choose the non-calculator filter to rehearse Paper 1, which counts for a third of the marks.
Geometry and measures worksheet — GCSE Foundation
MathsUKwww.geekhero.co.uk
- 1.To construct the perpendicular from a point P to a line l, where P is a point above l, an arc centred at P is drawn to cross l at two points, X and Y. What is the correct next step?
- 2.Triangles LMN and XYZ have LM = XY, MN = YZ and LN = XZ. Give a reason why triangle LMN is congruent to triangle XYZ.
- 3.A tap fills a tank at a rate of 18 litres per minute. The tank holds 0.45 m³. Work out how long the tap takes to fill the tank.
- 4.Write down the mathematical name for a quadrilateral that has exactly one pair of parallel sides.
- 5.A bearing is described as being exactly halfway between north and east, measured clockwise. What is the three-figure bearing?
- 6.Write down the column vector that describes a translation of 4 units to the right and 4 units up.
- 7.How many vertices does a cylinder have?
- 8.Write down the exact value of sin 60°.
- 9.A party hat is in the shape of a cone with a base radius of 6 cm and a slant height of 10 cm. Work out the curved surface area of the party hat. Use π = 3.14 and the formula curved surface area = πrl.
- 10.A scale drawing shows a room that is 5 cm wide. The real room is 15 m wide. Write the scale of the drawing in the form 1 : n.
- 11.A pop-up canopy has two sloping supports that meet at the top. Each support makes an angle of 30° with the ground and is 6 m long. Using the exact value of cos 30°, work out the total width of the canopy's base.
- 12.A tile is described as having two pairs of parallel sides, four equal sides, and diagonals that cross at right angles but are not equal in length. Give a reason why this tile cannot be a square.
- 13.Which pair of points lies on a horizontal line when the points are plotted on a coordinate grid?
- 14.A chord divides a circle into two regions, one larger than the other. Write down the term used for the smaller of these two regions.
- 15.A line segment joins two points on the circumference of a circle, without necessarily passing through the centre. Write down the general term for this line segment.
Answer key
- (a) Draw equal arcs from X and Y, meeting below line l. — After the first arc marks two points X and Y on line l, compasses are opened to a new radius and arcs of equal radius are drawn centred at X and at Y, so that they meet on the opposite side of l from P; joining P to that meeting point gives the perpendicular. (Joining X and Y with a straight line only retraces part of line l itself, since X and Y both already lie on it; drawing an arc centred at P through only one of X or Y repeats part of the first step instead of moving on; drawing a circle through X, Y and P does not locate the new point needed to complete the perpendicular.)
- (a) SSS – all three corresponding sides are equal — All three pairs of corresponding sides are stated as equal — LM = XY, MN = YZ and LN = XZ — with no angle mentioned. This matches the SSS condition, so triangle LMN is congruent to triangle XYZ.
- (b) 25 minutes — Method: a rate in litres per minute can only be used on a volume measured in litres, so convert the tank first and then divide. Working: 1 m³ = 1000 litres, so the tank holds 0.45 × 1000 = 450 litres, and the time is 450 ÷ 18 = 25. Answer: 25 minutes. Using 1 m³ = 100 litres gives 45 ÷ 18 = 2.5 minutes. Using 1 m³ = 1 000 000 litres, which is the factor that turns cubic metres into cubic centimetres, gives 450 000 ÷ 18 = 25 000 minutes. Multiplying by the rate instead of dividing by it gives 450 × 18 = 8100.
- (b) Trapezium — A trapezium is defined as a quadrilateral with exactly one pair of parallel sides. A parallelogram has two pairs of parallel sides, not one, so it does not fit the definition. A kite has no parallel sides at all. A rhombus, like a parallelogram, has two pairs of parallel sides. The correct name is trapezium.
- (b) 045° — North is 000° and east is 090°; halfway between them, measured clockwise, is 045°. Choosing 090° gives east itself, not the midpoint between north and east. Choosing 135° gives the midpoint between east (090°) and south (180°) instead of between north and east. Choosing 225° is the back bearing of 045° (045° + 180°), not the bearing itself.
- (a) $\binom{4}{4}$ — A movement to the right is a positive top number and a movement up is a positive bottom number, so 4 right and 4 up gives $\binom{4}{4}$. $\binom{4}{-4}$ wrongly gives the vertical movement a negative sign, as if it were downward. $\binom{-4}{4}$ wrongly gives the horizontal movement a negative sign, as if it were leftward. $\binom{-4}{-4}$ gets both signs wrong, as if the translation were left and down.
- (d) 0 — A vertex is a sharp corner point where edges meet. A cylinder has two curved, circular edges but no sharp corner points at all, so it has 0 vertices, making that the correct answer. '2' wrongly treats the two circular edges themselves as vertices, but an edge is not the same as a vertex. '4' overcounts by treating each circular edge as if it had two end-vertices, which does not apply to a continuous curved edge. '1' wrongly imagines the curved surface itself forming a single corner point, which it does not.
- (c) √3/2 — Method: sin 60° comes from half of an equilateral triangle. Cut an equilateral triangle of side 2 down its middle: each half is right-angled, with hypotenuse 2 and base 1, and Pythagoras gives its height as √3 because 2² − 1² = 3. Working: sine is the opposite side over the hypotenuse, the side opposite the 60° angle is the height √3, and the hypotenuse is 2, so sin 60° = √3 ÷ 2. Answer: sin 60° = √3/2. Swapping sine for cosine at this angle gives cos 60° = 1/2; taking the value from the other special triangle, the right-angled isosceles one, gives sin 45° = √2/2; and reading the tangent row instead of the sine row gives tan 60° = √3.
- (a) 188.4 cm² — Curved surface area of a cone = πrl. With r = 6 cm, l = 10 cm and π = 3.14, curved surface area = 3.14 × 6 × 10 = 188.4 cm². A student who uses the cylinder's curved surface area formula, 2πrl, instead of the cone's gets 2 × 3.14 × 6 × 10 = 376.8 cm². A student who uses the circle-area formula πr² instead of πrl gets 3.14 × 36 = 113.04 cm². A student who multiplies r × l but leaves out π entirely gets 6 × 10 = 60 cm².
- (c) 1 : 300 — First convert both lengths to the same unit: 15 m = 1500 cm. The scale compares 5 cm on the drawing to 1500 cm in real life, so dividing both parts by 5 gives a scale of 1 : 300. A candidate who compares 5 to 15 without converting units gets 1 : 3. A candidate who converts 15 m to 150 cm, using the wrong conversion factor, gets 1 : 30. A candidate who converts 15 m to 15000 cm, again using the wrong conversion factor, gets 1 : 3000. The scale of the drawing is 1 : 300.
- (b) 6√3 m — The horizontal distance covered by one support is adjacent to the 30° angle, so it equals 6 × cos 30° = 6 × √3/2 = 3√3 m. The total base width is made up of both supports, so it is 2 × 3√3 = 6√3 m. '3√3 m' gives only one support's horizontal distance and forgets to double it for the total width. '6 m' comes from using sin 30° instead of cos 30° for the horizontal distance (6 × sin 30° = 3, doubled to 6). '12 m' comes from doubling the full sloping length of 6 m without using any trigonometry at all.
- (a) A square's diagonals are equal in length — A square has two pairs of parallel sides, four equal sides, and diagonals that are equal in length and cross at right angles. This tile's diagonals are not equal, so it is a rhombus that is not a square.
- (c) (2, 4) and (6, 4) — Method: two points lie on the same horizontal line when they stand at the same height above the x-axis, and a point's height is given by its y-coordinate, the second number in the bracket. Working: compare the second numbers in each pair. For (3, 5) and (3, 8) they are 5 and 8, which differ. For (1, 2) and (2, 1) they are 2 and 1, which differ. For (0, 0) and (1, 1) they are 0 and 1, which differ. For (2, 4) and (6, 4) they are 4 and 4, which agree, so only that pair lies on a horizontal line. Answer: (2, 4) and (6, 4). The distractors: (3, 5) and (3, 8) comes from swapping horizontal for vertical, since equal x-coordinates place two points one above the other; (1, 2) and (2, 1) comes from looking for the same pair of numbers rather than for the same y-coordinate; (0, 0) and (1, 1) comes from reading 'horizontal' as simply 'in a straight line', which any two points are.
- (c) minor segment — A chord splits a circle into two segments; the smaller of the two is called the minor segment and the larger one the major segment. "major segment" names the larger region, the opposite of what is asked for. "sector" is a different region altogether, enclosed by two radii and an arc, not by a chord. "arc" is a curved length along the circumference, not an enclosed region at all.
- (a) Chord — Method: identify what the two endpoints of the line segment are, and whether it must pass through the centre. Working: a line joining any two points on the circumference, whether or not it passes through the centre, is a chord, and the diameter is just a special case of it. A student who answers diameter has wrongly assumed the line must pass through the centre. A student who answers radius has confused joining two circumference points with joining the centre to the circumference. A student who answers tangent has confused a line crossing through the circle with one that only touches its outside. Answer: chord.
Build your own mix at the worksheet builder.