Printable · GCSE Foundation · ages 14-16
Geometry and measures worksheet — GCSE Foundation
Fifteen questions across the geometry and measures statements at Foundation tier. Choose the non-calculator filter to rehearse Paper 1, which counts for a third of the marks.
Geometry and measures worksheet — GCSE Foundation
MathsUKwww.geekhero.co.uk
- 1.A roof truss has two horizontal parallel rafters, one above the other. A straight strut crosses both rafters. Where the strut crosses the lower rafter, the angle above the rafter and to the left of the strut is 65°. Work out the size of the angle above the upper rafter and to the right of the strut, where the strut crosses it.
- 2.In the RHS congruence condition, which three facts must be true about two triangles for RHS to prove they are congruent?
- 3.Here are four trigonometric ratios of special angles. Write down the one that does not have a value.
- 4.Which of the following is NOT one of the four basic conditions used to prove two triangles are congruent?
- 5.In a construction, a point P is marked at the foot of the perpendicular drawn from point X to a straight line. Which statement correctly compares the distance XP with the distance from X to any other point on the line?
- 6.In this question, a curved surface counts as a face. How many faces does a cone have?
- 7.In parallelogram ABCD the vertices are labelled in order round the shape, so angle A and angle B are at the two ends of the same side. Angle A is 70°. Work out the size of angle B.
- 8.How many faces does a cuboid have?
- 9.A cake recipe takes 135 minutes from start to finish. Write this time as hours and minutes.
- 10.A landscaper marks out two triangular flower beds using stakes and a tape measure. Bed 1 has two edges of 5 m and 7 m, meeting at a corner with a marked angle of 60° between them. Bed 2 has edges of 5 m and 7 m, meeting at a corner also marked at 60° between them. The landscaper wants to check the two beds will be exactly the same size and shape using only these three measurements. Which condition proves the two beds are congruent?
- 11.Priya says: 'To find the arc length of a sector, you divide the circumference by the angle in degrees.' Which statement about Priya's method is correct?
- 12.A carpenter cuts two triangular metal brackets for a shelf. Bracket P has sides of 12 cm, 16 cm and 20 cm. Bracket Q has sides of 16 cm, 20 cm and 12 cm, listed in a different order. Before fitting them as a matching pair, the carpenter wants to check they are exactly the same shape and size. Which of the following correctly justifies this?
- 13.A is the point (1, 3) and B is the point (7, 3). Work out the coordinates of the midpoint of AB.
- 14.A solid metal sphere has a radius of 5 cm. It is melted down and recast into a solid cylinder with the same radius, 5 cm. Work out the height of the cylinder, so that its volume equals the volume of the sphere. Use π = 3.14 and give your answer correct to 1 decimal place.
- 15.Write down the column vector that describes a translation of 4 units to the right and 4 units up.
Answer key
- (c) 115 — Method: use corresponding angles to carry the 65° angle from the lower rafter up to the upper rafter, then use angles on a straight line to move to the other side of the strut. Working: the angle above the upper rafter and to the left of the strut corresponds to the given angle, so it is 65°; the angle above the upper rafter and to the right of the strut lies on a straight line with it, so it is 180 − 65 = 115. Answer: 115°. A candidate who assumes the angle stays 65° without allowing for the move from the left of the strut to the right of it gives 65. A candidate who uses 90° instead of 180°, working out 90 − 65, gets 25. A candidate who adds instead of subtracting, working out 180 + 65, gets 245.
- (b) Right angle, equal hypotenuse, one more side — RHS requires a right angle in each triangle, equal hypotenuses, and one further pair of equal sides, so 'right angle, equal hypotenuse, one more side' is correct. 'Right angle, hypotenuse, one more angle' is wrong because it asks for an extra equal angle instead of an extra equal side, which RHS does not check. 'Two sides and the angle between them' describes SAS, not RHS, so it is wrong. 'Right angle and all three sides equal' describes SSS with an extra right-angle condition, asking for more information than RHS actually needs, so it is wrong.
- (b) tan 90° — Method: write each ratio as one side of a right-angled triangle divided by another, and look for the one whose bottom line can be zero. Working: sine and cosine are both a side divided by the hypotenuse, and a hypotenuse is never zero, so sin 90° = 1 and cos 90° = 0 are both perfectly good values — a value of zero is still a value. Tangent is the opposite side divided by the adjacent side. As the angle opens out towards 90° the adjacent side shrinks to nothing, and a division by zero has no result, while at the other end of the row the adjacent side is the long one and tan 0° = 0. Answer: tan 90°.
- (c) SSA — Method: recall the four basic congruence criteria for triangles and compare them with each option. Working: the four basic conditions are SSS, SAS, ASA and RHS. SSA (two sides and a non-included angle) is not one of them, because knowing two sides and an angle that is not between them does not always fix a unique triangle. Options: SSS, ASA and RHS are each genuine congruence conditions, so none of them is the correct answer to 'which is NOT'. Answer: SSA.
- (d) XP is the shortest distance from X to the line — The perpendicular from a point to a line always gives the shortest possible distance to that line — joining X to any other point on the line forms the hypotenuse of a right-angled triangle with XP as one of the shorter sides, and a hypotenuse is always longer than either of the other two sides. So XP is shorter than the distance to every other point on the line. "XP is the longest distance from X to the line" reverses this relationship. "XP equals every other distance from X to the line" would only be true if X were equidistant from every point on the line, which is impossible for a point and a straight line. "XP cannot be compared without knowing the line's length" is false — the shortest-distance fact holds whatever the line's length, since only the local right angle matters.
- (a) 2 — A cone has one flat face — the circular base — and one curved surface, which is counted as a single face. That gives a total of 2 faces. A candidate who forgets the circular base and counts only the curved surface answers 1. A candidate who mistakenly splits the curved surface into two faces answers 3. A candidate who thinks a cone has no flat faces at all answers 0. The correct number of faces is 2.
- (a) 110° — Method: in a parallelogram the two angles at the ends of one side are co-interior angles between a pair of parallel sides, so they add up to 180°. Working: angle A + angle B = 180°, so angle B = 180° − 70° = 110°. Answer: 110°. The distractors: 70° comes from applying the rule for opposite angles of a parallelogram, which are equal, to two angles that are next to each other instead; 20° comes from treating the two angles as complementary and working out 90° − 70°; 290° comes from using the 360° angle sum of a quadrilateral and taking away only the one angle that is given, 360° − 70°.
- (c) 6 — A cuboid has six flat faces: a top, a bottom and four sides. Count each flat surface once: top, bottom, front, back, left, right — six faces in total, so the answer is 6. Choosing 8 counts the vertices (corners) instead of the faces. Choosing 12 counts the edges instead of the faces. Choosing 4 counts only the four side faces and forgets the top and the bottom.
- (c) 2 hours 15 minutes — Divide the total minutes by 60: 135 ÷ 60 = 2 remainder 15, so that is 2 hours 15 minutes. Treating 100 minutes as one hour, a metric-style mistake, gives 135 − 100 = 35, so 1 hour 35 minutes. Subtracting 60 twice to reach the 15 minutes left over, but losing count and recording only one of the two hours removed, gives 1 hour 15 minutes. Writing 135 ÷ 60 = 2.25 and then reading the '25' as minutes, instead of converting the 0.25 of an hour into 15 minutes, gives 2 hours 25 minutes.
- (b) SAS — Method: check which condition matches two sides and the angle between them, since that is what has been measured for each bed. Working: the 60° angle is marked at the corner where the 5 m and 7 m edges meet, so it is the included angle — this is two Sides and the included Angle, SAS. Options: SSS would need a third side measured, but only two edges are known; ASA would need two angles and the side between them, but only one angle is measured; RHS needs a right angle, and 60° is not a right angle. Answer: SAS.
- (a) Wrong: multiply by angle ÷ 360, not divide by it. — The arc length is the fraction angle ÷ 360 of the circumference, and that fraction is MULTIPLIED by the circumference — it is never divided by the angle itself. So Priya's method, dividing by the angle, is wrong, and the correct statement names both the fraction and the multiplication. Saying she is correct accepts her wrong division. Saying the arc length is the full circumference multiplied by the angle in degrees, with no division at all, drops the 360 that turns the angle into a fraction. Saying the arc length is the radius multiplied by the angle in degrees swaps the circumference for the radius, which is a different and, in degrees, incorrect formula.
- (a) Yes - SSS, the three side lengths all match — Bracket P's sides (12 cm, 16 cm, 20 cm) can each be matched to one of Bracket Q's sides (16 cm, 20 cm, 12 cm) — the same three lengths, just listed differently — so the brackets are congruent by SSS. SAS is wrong here because no angle is stated for either bracket, only three sides. The order the sides are listed in does not matter for SSS — only whether the SET of three lengths matches, and it does, so 'listed in a different order' is not a reason to say no. Nothing extra is needed: SSS proves congruence from side lengths alone, without any angles, so it can be determined.
- (c) (4, 3) — Method: the midpoint of a segment is the mean of its two end points, so its x-coordinate is the mean of the two x-coordinates and its y-coordinate is the mean of the two y-coordinates. Working: for x, (1 + 7) ÷ 2 = 8 ÷ 2 = 4. For y, (3 + 3) ÷ 2 = 6 ÷ 2 = 3. The midpoint is therefore (4, 3). Answer: (4, 3). The distractors: (3, 3) comes from halving the difference of the x-coordinates, (7 − 1) ÷ 2 = 3, which measures half the distance instead of locating the point; (3.5, 3) comes from halving only the larger x-coordinate and leaving the smaller one out of the working; (4, 0) comes from averaging the x-coordinates correctly but then subtracting the y-coordinates, 3 − 3, rather than averaging them.
- (d) 6.7 cm — Volume of the sphere = (4/3)πr³ = (4/3) × 3.14 × 5³ = (4/3) × 3.14 × 125 = 523.33 cm³. Set this equal to the cylinder's volume πr²h: 523.33 = 3.14 × 25 × h = 78.5h. Divide: h = 523.33 ÷ 78.5 = 6.667 cm, which rounds to 6.7 cm. 1.7 cm comes from using the sphere's diameter, 10 cm, as the cylinder's radius: 523.33 ÷ (3.14 × 10²) = 1.7 cm.
- (a) $\binom{4}{4}$ — A movement to the right is a positive top number and a movement up is a positive bottom number, so 4 right and 4 up gives $\binom{4}{4}$. $\binom{4}{-4}$ wrongly gives the vertical movement a negative sign, as if it were downward. $\binom{-4}{4}$ wrongly gives the horizontal movement a negative sign, as if it were leftward. $\binom{-4}{-4}$ gets both signs wrong, as if the translation were left and down.
Build your own mix at the worksheet builder.