Printable · GCSE Foundation · ages 14-16
Geometry and measures worksheet — GCSE Foundation
Fifteen questions across the geometry and measures statements at Foundation tier. Choose the non-calculator filter to rehearse Paper 1, which counts for a third of the marks.
Geometry and measures worksheet — GCSE Foundation
MathsUKwww.geekhero.co.uk
- 1.Triangle T has a vertex at (2, 1). It is enlarged by a scale factor of 3, centre (0, 0). Work out the coordinates of the image of this vertex.
- 2.A shape is translated by the vector , and one vertex of the image is at the point (1, 6). The original shape is instead translated by the vector . Work out the coordinates of the image of that same vertex under this second translation.
- 3.A ladder of length 7 m leans against a vertical wall. The foot of the ladder is 3 m from the base of the wall. Work out how high up the wall the ladder reaches. Give your answer correct to 1 decimal place.
- 4.A circle has centre O. Radii OA and OB are drawn, together with the arc AB, enclosing a sector. The straight chord AB is also drawn. Write down the name of the region enclosed between the chord AB and the arc AB.
- 5.A dog is tied by a lead 4 m long to a fixed ring on a straight garden wall. The wall extends much further than the lead can reach in both directions, and the dog cannot cross through it. Describe the region the dog can reach.
- 6.A church tower is due east of a village. What is the three-figure bearing of the church tower from the village?
- 7.The diagram shows the plan view and the front elevation of a cuboid-shaped box, each drawn as a rectangle. Work out the area of the box's side elevation, in square centimetres.
- 8.A rectangular garden bed measures 5 m by 3 m. A semicircular flower border is attached along one of the 3 m-wide ends, on the outside of the rectangle, so that the 3 m side is the diameter of the semicircle. Work out the total perimeter of the combined shape (the two long sides, the one remaining short side, and the curved edge). Use π = 3.14.
- 9.A solid is built from centimetre cubes: a base layer of 2 rows of 3 cubes each (a 3 by 2 rectangle of cubes), with one extra cube placed on top of one corner cube of that base. Looking down from directly above (the plan view), how many squares are visible?
- 10.A scale drawing uses a scale of 1 : 60. A path on the drawing is measured as 9.8 cm long. What is the real length of the path, in metres, to 1 decimal place?
- 11.A zip wire is fixed at an angle of 50° to the horizontal, running from a high platform down to the ground. The zip wire itself, from the platform to the ground, is 12 m long. Work out the horizontal distance covered by the zip wire. Give your answer correct to 1 decimal place.
- 12.A plan of a car park is drawn to a scale of 1 : 500. A parking bay is drawn as a rectangle measuring 1.2 cm by 0.6 cm. The real width of the bay corresponds to the 0.6 cm side. What is the real width of the bay, in metres?
- 13.Triangle ABC has AB = 6 cm and BC = 9 cm, with angle A = 40°. Triangle DEF has DE = 6 cm and EF = 9 cm, with angle D = 40°. Meera says these facts prove the triangles are congruent by SAS. Is Meera correct?
- 14.Quadrilateral ABCD has vertices A(1, 1), B(5, 1), C(5, 4) and D(1, 4). The quadrilateral is translated by the vector . Which of these points is NOT a vertex of the image?
- 15.In quadrilateral ABCD the two sides AB and BC are each 6 cm long and meet each other at B. The two sides CD and DA are each 9 cm long and meet each other at D. No side of ABCD is parallel to any other side. Write down the mathematical name of this quadrilateral.
Answer key
- (d) (6, 3) — For an enlargement centred at the origin, each coordinate is multiplied by the scale factor: (2, 1) → (2 × 3, 1 × 3) = (6, 3). ((5, 4) comes from adding the scale factor to each coordinate instead of multiplying; (6, 1) comes from multiplying only the x-coordinate by 3 and leaving the y-coordinate unchanged; (2, 3) comes from multiplying only the y-coordinate by 3 and leaving the x-coordinate unchanged.)
- (d) (11, −2) — First undo the original translation to find the vertex on the original shape: (1 − (−8), 6 − 3) = (9, 3). Then apply the second vector to that original vertex: (9 + 2, 3 + (−5)) = (11, −2). (3, 1) comes from applying the second vector to the image point (1, 6) instead of to the original vertex — (1 + 2, 6 + (−5)) = (3, 1). (7, 8) comes from subtracting the second vector from the original vertex (9, 3) instead of adding it — (9 − 2, 3 − (−5)) = (7, 8). (11, 3) comes from applying only the x-component of the second vector to the original vertex and leaving the y-coordinate unchanged.
- (c) 6.3 m — By Pythagoras' theorem, the height = √(7² − 3²) = √(49 − 9) = √40 = 6.32...≈ 6.3 m. "6.4 m" rounds 6.32...m up to 6.4 instead of correctly rounding it down to 6.3. "4.0 m" comes from subtracting the two given lengths directly, 7 − 3 = 4, instead of subtracting their squares. "10.0 m" comes from adding the two given lengths, 7 + 3 = 10, instead of using Pythagoras' theorem at all.
- (b) segment — The region enclosed between a chord and the arc it cuts off is called a segment. A sector is the different region already named in the question, enclosed by the two radii and the arc, not by the chord. A tangent is a straight line that touches the circle at one point, not an enclosed region at all. The circumference is the total distance around the whole circle, a length, not a region.
- (b) A semicircle of radius 4 m, away from the wall. — Every point the dog can reach is at most 4 m from the fixed ring, so without any wall the region would be a full circle of radius 4 m. The wall runs straight through the ring and blocks the dog from crossing it, and since the wall extends further than the lead in both directions, exactly half of that circle is cut off — leaving a semicircle of radius 4 m on the side of the wall the dog is tied on. (A full circle of radius 4 m ignores that the wall blocks half of the region; a quarter circle of radius 4 m would only be correct if the ring were fixed at a corner where two walls met, not along a single straight wall; a rectangle 4 m wide along the wall ignores that the lead lets the dog swing round in a curve, not stay a fixed distance out from the wall.)
- (c) 090 — Method: bearings are measured clockwise from north; east is a quarter turn clockwise. Working: a quarter turn is 90°, written with a leading zero as three figures. A student who answers 009 has kept the correct digits but put the leading zero in the wrong place. A student who answers 180 has confused east with south. A student who answers 270 has confused east with west. Answer: 090.
- (d) 15 cm² — Method: identify the length that is common to both views, since it is the box's length; then read off the width from the plan view and the height from the front elevation, and multiply those two measurements to find the area of the side elevation. Working: both rectangles share a side of 8 cm, which is the box's length; the plan view's other side gives a width of 5 cm, and the front elevation's other side gives a height of 3 cm. The side elevation is bounded by the width and the height: 5 cm × 3 cm = 15 cm². Answer: 15 cm². The distractors: 24 cm² comes from giving the area of the front elevation shown (8 cm × 3 cm) instead of working out a new rectangle for the side elevation. 40 cm² comes from giving the area of the plan view shown (8 cm × 5 cm) instead of working out the side elevation. 120 cm² comes from multiplying all three measurements together (8 cm × 5 cm × 3 cm), finding the volume of the box instead of the area of one face.
- (c) 17.71 m — The perimeter is the two long sides (5 m + 5 m = 10 m) plus the one remaining short side (3 m) plus the curved semicircular edge. The 3 m side is the diameter of the semicircle, so its radius is 3 ÷ 2 = 1.5 m and the curved length is half the circumference: (1/2) × 2 × 3.14 × 1.5 = 4.71 m. Total: 10 + 3 + 4.71 = 17.71 m.
- (d) 6 — The plan view shows every square of the base footprint, whether or not there is a taller stack above it — the base layer alone already covers a 3 by 2 rectangle of cubes, which is 6 squares. The extra cube on top of a corner cube sits directly above a square that is already counted, so it adds no NEW square to the plan — height does not show up in a plan view, only footprint does. "7" comes from wrongly counting the extra cube as an additional square. "5" comes from missing one square of the base rectangle, perhaps forgetting a corner. "3" comes from counting only one row of the base rectangle and forgetting that the base is two rows deep.
- (a) 5.9 — The real length is 9.8 × 60 = 588 cm. Converting to metres, by dividing by 100, gives 5.88 m, which rounds to 5.9 m to 1 decimal place. A candidate who rounds 5.88 down instead of up gets 5.8 m. A candidate who forgets to convert from centimetres to metres gets 58.8. A candidate who divides by 60 instead of multiplying gets 0.16, to 2 decimal places. The real length, to 1 decimal place, is 5.9 m.
- (d) 7.7 m — The horizontal distance is adjacent to the 50° angle and the zip wire is the hypotenuse, so horizontal distance = 12 × cos 50° = 12 × 0.6428... = 7.71...≈ 7.7 m. "9.2 m" uses the sine ratio instead of cosine, 12 × sin 50° = 9.19...≈ 9.2 m, which actually finds the vertical drop of the zip wire, not the horizontal distance. "15.7 m" comes from dividing by the sine ratio instead of multiplying by the cosine ratio, 12 ÷ sin 50° = 15.66...≈ 15.7 m, both the wrong operation and the wrong ratio. "12.0 m" simply uses the length of the zip wire itself as the horizontal distance, ignoring the angle of 50° altogether.
- (b) 3 — The real width is 0.6 × 500 = 300 cm, which converts to 3 m by dividing by 100. A candidate who uses the wrong side of the rectangle, 1.2 cm, instead of the 0.6 cm width, gets 1.2 × 500 = 600 cm = 6 m. A candidate who multiplies correctly but converts the 300 cm to metres by dividing by 1000 instead of 100 gets 0.3 m. A candidate who converts by dividing by 10 instead of 100 gets 30 m. The real width of the bay is 3 m.
- (b) No — the angle given is not the included angle — Method: check whether the given angle sits between the two given sides, since SAS requires the included angle. Working: sides AB and BC meet at vertex B, so the angle between them is angle B — but the angle given is angle A, which is not between the two given sides, and the same mismatch happens in triangle DEF. Options: 'two sides and one angle match' restates SAS's ingredients without checking their positions, which is exactly Meera's mistake; 'SSS needs three equal sides' is a true fact about a different condition, but it is not the reason Meera is wrong here; 'SAS allows any equal angle' states a rule that is not how SAS works, since the angle must be the included one. Answer: no, the angle given is not the included angle.
- (a) (−1, 1) — Translating by $\binom{−2}{3}$ subtracts 2 from every x-coordinate and adds 3 to every y-coordinate. This gives image vertices (−1, 4), (3, 4), (3, 7) and (−1, 7). The point (−1, 1) is not one of these: it has the correct new x-coordinate (1 − 2 = −1) but keeps the original y-coordinate (1) instead of adding 3, as if only the horizontal part of the vector had been applied.
- (b) Kite — Method: name a quadrilateral by matching what is given — which sides are equal, whether those equal sides lie next to each other or opposite each other, and whether any sides are parallel — against the definitions of the special quadrilaterals. Working: the two 6 cm sides meet at B and the two 9 cm sides meet at D, so each pair of equal sides is a pair of neighbours rather than a pair of opposites, and the stem rules out any parallel sides. The quadrilateral with two pairs of equal adjacent sides and no parallel sides is a kite. Answer: kite. The distractors: a rhombus is chosen by candidates who see two pairs of equal sides and read that as all four sides being equal, which the two different lengths of 6 cm and 9 cm rule out; a parallelogram is chosen by candidates who remember that a parallelogram has two pairs of equal sides but not that in a parallelogram the equal sides are the opposite ones, and who pass over the statement that nothing is parallel; an isosceles trapezium is chosen by candidates who notice that the shape is symmetrical about the line BD and treat symmetry on its own as the mark of a trapezium, when a trapezium needs a pair of parallel sides.
Build your own mix at the worksheet builder.