Printable · GCSE Foundation · ages 14-16
Geometry and measures worksheet — GCSE Foundation
Fifteen questions across the geometry and measures statements at Foundation tier. Choose the non-calculator filter to rehearse Paper 1, which counts for a third of the marks.
Geometry and measures worksheet — GCSE Foundation
MathsUKwww.geekhero.co.uk
- 1.A television cable runs in a straight line from the edge of a flat roof 20 m above the ground to a bracket on a wall 5 m above the ground. The horizontal distance between the roof edge and the bracket is 15 m. Work out the length of the cable. Give your answer to 1 decimal place.
- 2.A packaging designer is told a box has 6 faces, 12 edges and 8 vertices, and every face is a rectangle. To fit exactly onto a shelf, the designer needs to know whether the box must be a cube. Based only on this information, which solid must the box be?
- 3.A roof truss is shaped like an isosceles triangle resting on a horizontal ceiling joist. The truss's sloping edges are equal in length, and the angle at its apex is 40°. The ceiling joist continues in a straight line beyond the foot of the truss. Work out the angle between the truss's sloping edge and the extended joist, on the outside of the truss.
- 4.The point M(3, 8) is translated by the vector . Write down the coordinates of the image of M.
- 5.Point A has coordinates (2, 5). Point A is translated to point B using the column vector with top number 6 and bottom number −3. Write down the coordinates of point B.
- 6.A sector of a circle has an angle of 90° and an arc length of 15.7 cm. Using π = 3.14, work out the radius of the circle.
- 7.A wooden cube has edges of length 4 cm. Work out the total surface area of the cube.
- 8.Triangle A has a vertex at (1, 2). Triangle A is enlarged, centre (1, 1), to give triangle B, whose corresponding vertex is at (1, 5). Work out the scale factor of the enlargement.
- 9.A sailmaker cuts two triangular sail panels from a pattern. Panel X has a 10 m side, with angles of 50° and 75° at its two ends. Panel Y also has a 10 m side, with angles of 50° and 75° at its two ends, in the same arrangement. The sailmaker wants to check the panels will match exactly, without cutting a third measurement. Which condition proves the two panels are congruent?
- 10.A diameter divides a circle into two equal halves. Write down the special name given to each of these two halves.
- 11.Work out the exact value of cos 0° − sin 30°.
- 12.A cake recipe takes 135 minutes from start to finish. Write this time as hours and minutes.
- 13.The point R(−6, 9) is translated by the vector . Write down the coordinates of the image of R.
- 14.A trapezium has parallel sides of 5 cm and 11 cm, and a perpendicular height of 4 cm. Work out the area of the trapezium.
- 15.A chord divides a circle into two regions, one larger than the other. Write down the term used for the smaller of these two regions.
Answer key
- (d) 21.2 m — Method: the cable is the hypotenuse of a right-angled triangle whose vertical side is the drop from the roof to the bracket and whose horizontal side is 15 m, so use Pythagoras' theorem. Working: the drop is 20 − 5 = 15 m, so c² = 15² + 15² = 225 + 225 = 450 and c = √450 = 21.213…, which is 21.2 m to 1 decimal place. Answer: 21.2 m. The distractors: 25.0 m comes from using the whole 20 m height of the roof as the vertical side and forgetting that the bracket is already 5 m up; 30.0 m comes from adding the two sides of the triangle, 15 + 15, instead of using Pythagoras' theorem; 15.0 m is the horizontal distance on its own, which would be the length of the cable only if it ran level.
- (b) Cuboid — not necessarily a cube — A solid with 6 faces, 12 edges and 8 vertices in which every face is a rectangle is a cuboid, but nothing here confirms that all the edges are the same length, so the box could be a cube or a non-cube cuboid; the most that can be concluded is that it is a cuboid, making 'Cuboid — not necessarily a cube' correct. 'Cube — only a cube fits this' is wrong because a cube is just one particular cuboid; a general cuboid with different length, width and height has exactly the same face, edge and vertex counts and rectangular faces. 'Triangular prism' is wrong because a triangular prism has 5 faces, 9 edges and 6 vertices, and two of its faces are triangles, so it matches neither the counts nor the face shape. 'Not enough information' is wrong because rectangular faces with these counts do pin the solid down to the cuboid family, even though they cannot pin down a cube specifically.
- (a) 110° — The truss is isosceles, so its two base angles are equal; since the three angles of the triangle add up to 180° and the apex is 40°, each base angle is (180 − 40) ÷ 2 = 70°. The angle between the sloping edge and the joist, extended beyond the base of the truss, sits on a straight line with that 70° base angle, and angles on a straight line add up to 180°, so the required angle is 180 − 70 = 110°. "70°" comes from stopping after finding the base angle and giving it directly, without also using the straight-line fact to find the angle on the OUTSIDE of the truss. "140°" comes from doubling the base angle instead of using the straight-line fact. "20°" comes from taking half of the apex angle (40° ÷ 2), mistaking it for the required angle instead of properly using the triangle's angle sum.
- (c) (−2, 10) — To translate M(3, 8) by $\binom{−5}{2}$, add −5 to the x-coordinate and 2 to the y-coordinate: (3 + (−5), 8 + 2) = (−2, 10). (5, 3) comes from swapping the two components of the vector before applying them. (−2, 8) applies only the x-component and forgets to add the y-component. (3, 10) applies only the y-component and forgets to add the x-component.
- (a) (8, 2) — Method: translating a point by a column vector means adding the vector's top number to the x-coordinate and its bottom number to the y-coordinate. Working: x-coordinate 2 + 6 = 8; y-coordinate 5 + (−3) = 2. Answer: B = (8, 2). A candidate who ignores the negative sign and adds 3 instead of −3 gets (8, 8). A candidate who translates in the reverse direction, subtracting the vector from A instead of adding it, gets (−4, 8). A candidate who swaps the vector's top and bottom numbers before adding gets (−1, 11).
- (b) 10 cm — Arc length = (angle ÷ 360) × 2 × π × r, so 15.7 = (90 ÷ 360) × 2 × 3.14 × r = 1.57r, giving r = 15.7 ÷ 1.57 = 10 cm. (2.5 cm comes from forgetting the angle fraction and dividing by 2π alone; 20 cm comes from leaving out the factor of 2 in the arc length formula before dividing; 5 cm comes from dividing the arc length by π alone, ignoring both the angle fraction and the factor of 2.)
- (a) 96 cm² — Method: a cube has six identical square faces, so the total surface area is six times the area of one face. Working: one face has area 4 × 4 = 16 cm², and 6 × 16 = 96. Answer: 96 cm². The distractors: 16 cm² is the area of a single face, from stopping before multiplying by the six faces; 64 cm³ comes from working out the volume, 4 × 4 × 4, which is a different measure and carries a different unit; 24 cm² comes from multiplying the six faces by the edge length, 6 × 4, instead of by the area of a face.
- (b) 4 — The scale factor is the distance from the centre to the image, divided by the distance from the centre to the object: (5 − 1) ÷ (2 − 1) = 4 ÷ 1 = 4. (2.5 comes from dividing the raw y-coordinates, 5 ÷ 2, without first subtracting the centre's coordinate; 3 comes from subtracting the two distances instead of dividing them; 0.25 comes from dividing the distances the wrong way round.)
- (c) ASA — Method: check which condition matches two angles and the side between them, since that is all the sailmaker has measured. Working: the 10 m side lies between the 50° and 75° angles in both panels, so this is two Angles and the included Side, ASA. Options: SAS would need two sides and the angle between them, but only one side has been measured here; SSS would need three sides, but only one is known; RHS needs a right angle and a hypotenuse, and neither panel has a stated right angle. Answer: ASA.
- (b) Semicircle — Method: recall the special name for exactly half of a circle. Working: a diameter splits the circle into two identical halves, and each half has its own specific name. A student who answers segment has confused this special case with the general region cut off by any chord. A student who answers sector has confused it with the pie-slice shape made by two radii. A student who answers arc has only named the curved edge, not the whole two-dimensional region. Answer: semicircle.
- (a) 1/2 — cos 0° = 1 and sin 30° = 1/2, so cos 0° − sin 30° = 1 − 1/2 = 1/2. 1 comes from writing down cos 0° alone and forgetting to subtract sin 30°. 3/2 comes from adding the two values instead of subtracting. −1/2 comes from working out sin 30° − cos 0°, the two terms the wrong way round.
- (c) 2 hours 15 minutes — Divide the total minutes by 60: 135 ÷ 60 = 2 remainder 15, so that is 2 hours 15 minutes. Treating 100 minutes as one hour, a metric-style mistake, gives 135 − 100 = 35, so 1 hour 35 minutes. Subtracting 60 twice to reach the 15 minutes left over, but losing count and recording only one of the two hours removed, gives 1 hour 15 minutes. Writing 135 ÷ 60 = 2.25 and then reading the '25' as minutes, instead of converting the 0.25 of an hour into 15 minutes, gives 2 hours 25 minutes.
- (b) (−1, −2) — To translate R(−6, 9) by $\binom{5}{−11}$, add 5 to the x-coordinate and −11 to the y-coordinate: (−6 + 5, 9 + (−11)) = (−1, −2). (−1, 9) applies only the x-component and leaves the y-coordinate unchanged. (−6, −2) applies only the y-component and leaves the x-coordinate unchanged. (−11, 20) comes from subtracting the vector instead of adding it.
- (a) 32 cm² — Area of a trapezium = 1/2 × (sum of parallel sides) × height = 1/2 × (5 + 11) × 4 = 1/2 × 16 × 4 = 32 cm². (64 cm² comes from forgetting to halve the product; 44 cm² comes from using only the longer parallel side, 11 × 4, instead of both parallel sides; 20 cm² comes from adding all three given lengths together, 5 + 11 + 4, instead of using the area formula.)
- (c) minor segment — A chord splits a circle into two segments; the smaller of the two is called the minor segment and the larger one the major segment. "major segment" names the larger region, the opposite of what is asked for. "sector" is a different region altogether, enclosed by two radii and an arc, not by a chord. "arc" is a curved length along the circumference, not an enclosed region at all.
Build your own mix at the worksheet builder.