Printable · GCSE Foundation · ages 14-16
Geometry and measures worksheet — GCSE Foundation
Fifteen questions across the geometry and measures statements at Foundation tier. Choose the non-calculator filter to rehearse Paper 1, which counts for a third of the marks.
Calculator
Answer key: Geometry and measures worksheet — GCSE Foundation
MathsUKwww.geekhero.co.uk
- (c) 1 : 300 — First convert both lengths to the same unit: 15 m = 1500 cm. The scale compares 5 cm on the drawing to 1500 cm in real life, so dividing both parts by 5 gives a scale of 1 : 300. A candidate who compares 5 to 15 without converting units gets 1 : 3. A candidate who converts 15 m to 150 cm, using the wrong conversion factor, gets 1 : 30. A candidate who converts 15 m to 15000 cm, again using the wrong conversion factor, gets 1 : 3000. The scale of the drawing is 1 : 300.
- (d) 4.44 m — The real van's length is 18.5 × 24 = 444 cm, which converts to 4.44 m. '0.77 m' comes from dividing by 24 instead of multiplying, using the ratio the wrong way round (18.5 ÷ 24 = 0.77 cm), and then writing that figure down as metres. '44.4 m' comes from converting 444 cm to metres with the decimal point in the wrong place. '444 m' comes from working out 444 cm correctly but forgetting to convert it into metres at all.
- (d) 63.6 — Method: the three angles inside the triangle formed by the two ladders and the ground add up to 180°. Working: 180 − 58.2 − 58.2 = 63.6. Answer: 63.6°. A candidate who assumes the top angle equals the base angles gives 58.2. A candidate who subtracts only one base angle from 180°, working out 180 − 58.2, gets 121.8. A candidate who doubles the base angle instead of subtracting it twice from 180°, working out 2 × 58.2, gets 116.4.
- (c) 25 m — The gardener needs the circumference, since the trim goes around the flower bed. Circumference = πd = 3.14 × 8 = 25.12 m, which rounds to 25 m. A student who mistakes the diameter (8 m) for the radius, then doubles it before multiplying by π, gets 3.14 × 16 = 50.24 m, rounding to 50 m. A student who makes the same mistake but uses the area formula instead of the circumference gets 3.14 × 8² = 200.96 m², rounding to 201. A student who correctly halves the diameter to find the radius (4 m) but then uses πr instead of πd gets 3.14 × 4 = 12.56 m, rounding to 13 m.
- (d) 36.9° — sin θ = opposite/hypotenuse = 6/10 = 0.6, so θ = sin⁻¹(0.6) = 36.86...° ≈ 36.9°. "53.1°" finds the OTHER acute angle in the triangle, 90° − 36.9°, instead of θ itself, as if the two acute angles had been swapped. "31.0°" comes from using the tangent ratio instead of sine, working out tan⁻¹(6/10) = 31.0° with the wrong ratio for the two sides given. "36.8°" rounds sin⁻¹(0.6) = 36.86...° down to 36.8° instead of correctly rounding it up to 36.9°.
- (c) 1.44 m³ — The cross-section is a triangle, so its area = base × height ÷ 2. Base × height = 1.2 × 0.8 = 0.96 m², and half of that is 0.96 ÷ 2 = 0.48 m². The volume of the prism = cross-sectional area × length = 0.48 × 3 = 1.44 m³. A pupil who forgets to halve when finding the triangle's area gets 1.2 × 0.8 × 3 = 2.88 m³. A pupil who ignores the height altogether, treating the cross-section as base × length, gets 1.2 × 3 = 3.6 m³. A pupil who correctly finds the cross-sectional area but forgets to multiply by the length of the bed stops at 0.48 m³. The correct volume of soil is 1.44 m³.
- (c) 151,200 cm² — First find the area in m²: 4.2 × 3.6 = 15.12 m². To convert m² to cm², multiply by 10,000, since 1 m² = 100 cm × 100 cm = 10,000 cm²: 15.12 × 10,000 = 151,200 cm². 15.12 cm² gives the area in m² without converting the units at all. 1,512 cm² multiplies by 100 instead of 10,000, treating the conversion as if it were for a single length rather than an area. 15,120 cm² multiplies by 1,000 instead of 10,000.
- (d) sector — The region enclosed by two radii and the arc between them is called a sector. A segment is a different region, enclosed by a CHORD and an arc — it does not touch the centre at all. A chord is a straight line, not a region, so it cannot be the answer to a question asking for a region. A semicircle is only correct when the angle between the two radii is exactly 180°, which is not stated here, so it is too specific to be the general answer.
- (d) positive — Moving from A to B, the x-coordinate increases from 1 to 4 and the y-coordinate also increases from 1 to 7, so the line rises as it goes from left to right, which means the gradient is positive. "negative" would need y to decrease as x increases, which is not the case here. "zero" would need the y-coordinate to stay the same, but it changes from 1 to 7. "cannot be determined" is wrong because the coordinates of both points are known, so the direction of the line can always be found.
- (a) 188.4 cm² — Curved surface area of a cone = πrl. With r = 6 cm, l = 10 cm and π = 3.14, curved surface area = 3.14 × 6 × 10 = 188.4 cm². A student who uses the cylinder's curved surface area formula, 2πrl, instead of the cone's gets 2 × 3.14 × 6 × 10 = 376.8 cm². A student who uses the circle-area formula πr² instead of πrl gets 3.14 × 36 = 113.04 cm². A student who multiplies r × l but leaves out π entirely gets 6 × 10 = 60 cm².
- (d) 706.5 cm² — Area of a circle = πr². With r = 15 cm and π = 3.14, area = 3.14 × 15² = 3.14 × 225 = 706.5 cm². A student who uses the circumference formula 2πr instead of the area formula gets 2 × 3.14 × 15 = 94.2 cm². A student who uses πr instead, forgetting to double, gets 3.14 × 15 = 47.1 cm². A student who squares the diameter (30 cm) instead of the radius gets 3.14 × 900 = 2826.0 cm².
- (a) 376.8 cm³ — Volume of a cone = (1/3)πr²h. Substitute r = 6 and h = 10: (1/3) × 3.14 × 6² × 10 = (1/3) × 3.14 × 36 × 10 = (1/3) × 1130.4 = 376.8 cm³.
- (a) 250° — The back bearing (the bearing of A from B) differs from the bearing of B from A by exactly 180°. Because the given bearing, 070°, is less than 180°, add 180°: 070 + 180 = 250°, so the bearing of A from B is 250°. Choosing 180° assumes the back bearing is always exactly 180°, ignoring the original bearing altogether. Choosing 110° comes from subtracting 180° from 070° and dropping the negative sign (070 − 180 = −110) instead of adding 180°. Choosing 160° comes from adding only 90° instead of 180° (070 + 90 = 160).
- (d) 1535 cm² — The wiper sweeps out a sector of radius 40 cm, the blade length, through an angle of 110°. Sector area is angle ÷ 360 × π × radius²: 110 ÷ 360 × 3.14 × 1600 = 1535.1 cm², which rounds to 1535 cm². Forgetting to square the radius, using radius instead of radius², gives 38 cm². Using 110 ÷ 180 instead of 110 ÷ 360 for the fraction gives 3070 cm². Treating the 40 cm blade length as a diameter, so using a radius of 20 cm, gives 384 cm².
- (c) 3028 cm² — Split the window into a rectangle and a semicircle. Rectangle area = 40 × 60 = 2400 cm². The semicircle has radius 40 ÷ 2 = 20 cm, so its area = 0.5 × 3.14 × 20² = 628 cm². Total area = 2400 + 628 = 3028 cm². A student who uses a full circle instead of a semicircle on top of the rectangle gets 3.14 × 20² = 1256 cm² for the circle, plus 2400 cm² for the rectangle, totalling 3656 cm². A student who uses the rectangle's full width (40 cm) as the radius instead of halving it gets 0.5 × 3.14 × 40² = 2512 cm² for the semicircle, plus 2400 cm² for the rectangle, totalling 4912 cm².
Build your own mix at the worksheet builder.