Printable · GCSE Foundation · ages 14-16
Geometry and measures worksheet — GCSE Foundation
Fifteen questions across the geometry and measures statements at Foundation tier. Choose the non-calculator filter to rehearse Paper 1, which counts for a third of the marks.
Calculator
Answer key: Geometry and measures worksheet — GCSE Foundation
MathsUKwww.geekhero.co.uk
- (d) 6.4 cm — The scale factor from the larger sign to the smaller sign is 4 ÷ 9, so the smaller side is 14.4 × 4 ÷ 9 = 6.4 cm. The distractor 32.4 cm comes from using the ratio the wrong way round, 14.4 × 9 ÷ 4 = 32.4. The distractor 9.4 cm comes from subtracting the difference between the ratio numbers (9 − 4 = 5) from the given length, 14.4 − 5 = 9.4. The distractor 3.6 cm comes from dividing the given length by 4 only, 14.4 ÷ 4 = 3.6, without also using the other ratio number.
- (a) 62.8 cm — The ribbon goes once around the circular cross-section, so its length equals the circumference: 2πr = 2 × 3.14 × 10 = 62.8 cm.
- (b) £157 — Method: round the hours worked up to the next whole hour, multiply by the hourly rate, then add the call-out fee. Working: 3 hours 30 minutes rounds up to 4 hours; 28 × 4 = 112; 112 + 45 = 157. Answer: £157. A candidate who uses the unrounded time of 3.5 hours, working out 28 × 3.5 = 98 and adding 45, gets £143. A candidate who forgets the call-out fee, giving only 28 × 4, gets £112. A candidate who rounds down to 3 hours instead of up, working out 28 × 3 = 84 and adding 45, gets £129.
- (d) 6√3 cm — Method: AB lies alongside the 30° angle at A and AC is the hypotenuse, so the ratio needed is cosine: cos 30° = AB ÷ AC. Working: the exact value of cos 30° is √3/2, so AB = 12 × √3 ÷ 2, and half of 12 is 6. Answer: AB = 6√3 cm, which is about 10.4 cm. Using sine by mistake gives 12 × 1/2 = 6 cm, which is the length of BC rather than AB. Using tan 30° = 1/√3 gives 12 ÷ √3, which is 4√3 cm. Remembering cos 30° as √3 rather than as √3 halved gives 12√3 cm, longer than the hypotenuse and so impossible.
- (a) 080° — The back bearing differs from the given bearing by 180°. Because 260° is greater than 180°, subtract 180°: 260 − 180 = 80°, so the bearing of A from B is 080°. Choosing 440° adds 180° instead of subtracting it, even though the result would be more than a full turn (260 + 180 = 440). Choosing 180° assumes the back bearing is always exactly 180°, ignoring the original bearing altogether. Choosing 100° comes from measuring the reflex angle the other way round the circle (360 − 260 = 100) instead of applying the 180° back-bearing rule.
- (b) 320° — A bearing is always measured clockwise from north. An angle measured anticlockwise must be converted by subtracting it from 360°: 360 − 40 = 320°, so the bearing is 320°. Choosing 040° treats the anticlockwise angle as if it were already a clockwise bearing, without converting it. Choosing 220° adds 180° to the angle, mixing this up with a back-bearing calculation (40 + 180 = 220). Choosing 400° adds the angle to 360° instead of subtracting it (40 + 360 = 400), giving a bearing greater than a full turn.
- (a) 4700 cm² — Method: split the T-shaped outline into the two rectangles it is made from, find the area of each, then add them together. Working: the wide base gives a rectangle 90 cm × 30 cm = 2700 cm²; the narrower block on top gives a rectangle 40 cm × 50 cm = 2000 cm²; adding these, 2700 + 2000 = 4700 cm². Answer: 4700 cm². The distractors: 2700 cm² comes from finding only the area of the base rectangle and forgetting to add the block on top. 2000 cm² comes from finding only the area of the top block and forgetting the base. 7200 cm² comes from treating the whole outline as one large rectangle, 90 cm wide by (30 + 50) = 80 cm tall, instead of splitting it into the two separate rectangles that actually make up the shape.
- (a) 250° — The back bearing (the bearing of A from B) differs from the bearing of B from A by exactly 180°. Because the given bearing, 070°, is less than 180°, add 180°: 070 + 180 = 250°, so the bearing of A from B is 250°. Choosing 180° assumes the back bearing is always exactly 180°, ignoring the original bearing altogether. Choosing 110° comes from subtracting 180° from 070° and dropping the negative sign (070 − 180 = −110) instead of adding 180°. Choosing 160° comes from adding only 90° instead of 180° (070 + 90 = 160).
- (b) 10.5 m² — The area of a trapezium is half of the sum of the parallel sides, multiplied by the width. Add the parallel sides: 2.5 + 4.5 = 7. Multiply by the width: 7 × 3 = 21. Half of 21 is 10.5 m². 21 m² forgets to halve, using the full (2.5+4.5)×3. 3.5 m² averages the two parallel sides, (2.5+4.5)÷2 = 3.5, but forgets to multiply by the width. 6.75 m² treats the bed as a triangle, using only the longer parallel side: half of 4.5 × 3.
- (c) 56.52 cm² — Sector area = (45 ÷ 360) × 3.14 × 12² = 0.125 × 3.14 × 144 = 56.52 cm². (4.71 cm² comes from forgetting to square the radius; 452.16 cm² comes from finding the area of the whole circle and forgetting the angle fraction; 9.42 cm² comes from using the arc length formula instead of the sector area formula.)
- (b) (22, −13) — The vector from the ship to the lighthouse is (12, −4) − (2, 5) = (10, −9). Sailing along this vector twice from the start gives (2, 5) + 2 × (10, −9) = (2 + 20, 5 − 18) = (22, −13). '(12, −4)' stops after the ship reaches the lighthouse and ignores the second identical leg. '(−18, 23)' comes from finding the vector the wrong way round, as (2, 5) − (12, −4) = (−10, 9), and then doubling that. '(2, 5)' comes from adding the vector and then subtracting it again, wrongly cancelling the two legs instead of adding them.
- (b) 113.04 cm² — Sector area is (angle ÷ 360) × π × radius², and radius means the RADIUS, not the diameter: here the diameter is 24 cm, so the radius is 12 cm. The fraction is 90 ÷ 360 = 1/4, and 12² = 144, so the area is 0.25 × 3.14 × 144 = 113.04 cm². Using the diameter itself as if it were the radius gives 0.25 × 3.14 × 576 = 452.16 cm². Using the arc-length formula, 2 × π × radius, instead of the area formula gives 0.25 × 2 × 3.14 × 12 = 18.84 cm². Using the radius instead of its square gives 0.25 × 3.14 × 12 = 9.42 cm².
- (a) Yes - SSS, the three side lengths all match — Bracket P's sides (12 cm, 16 cm, 20 cm) can each be matched to one of Bracket Q's sides (16 cm, 20 cm, 12 cm) — the same three lengths, just listed differently — so the brackets are congruent by SSS. SAS is wrong here because no angle is stated for either bracket, only three sides. The order the sides are listed in does not matter for SSS — only whether the SET of three lengths matches, and it does, so 'listed in a different order' is not a reason to say no. Nothing extra is needed: SSS proves congruence from side lengths alone, without any angles, so it can be determined.
- (d) a² + b² = c² — Pythagoras' theorem states that the square of the hypotenuse equals the sum of the squares of the other two sides, so a² + b² = c². "a + b = c" adds the sides directly without squaring them at all. "a² − b² = c²" subtracts the squares instead of adding them. "a² + b² = c" adds the squares correctly but forgets to square the hypotenuse on the other side of the equation.
- (c) tan θ = opposite/adjacent — The tangent ratio is defined as tan θ = opposite/adjacent, so this is the ratio that connects the opposite and adjacent sides. "sin θ = opposite/adjacent" wrongly labels this ratio as sine, when sine actually connects the opposite side and the hypotenuse. "cos θ = opposite/adjacent" wrongly labels it as cosine, when cosine connects the adjacent side and the hypotenuse. "tan θ = adjacent/opposite" uses the correct ratio name but has the opposite and adjacent sides the wrong way round.
Build your own mix at the worksheet builder.