Printable · GCSE Foundation · ages 14-16
Geometry and measures worksheet — GCSE Foundation
Fifteen questions across the geometry and measures statements at Foundation tier. Choose the non-calculator filter to rehearse Paper 1, which counts for a third of the marks.
Calculator
Answer key: Geometry and measures worksheet — GCSE Foundation
MathsUKwww.geekhero.co.uk
- (a) 188.4 cm² — Curved surface area of a cone = πrl. With r = 6 cm, l = 10 cm and π = 3.14, curved surface area = 3.14 × 6 × 10 = 188.4 cm². A student who uses the cylinder's curved surface area formula, 2πrl, instead of the cone's gets 2 × 3.14 × 6 × 10 = 376.8 cm². A student who uses the circle-area formula πr² instead of πrl gets 3.14 × 36 = 113.04 cm². A student who multiplies r × l but leaves out π entirely gets 6 × 10 = 60 cm².
- (c) 460 g — Each division is 20 g, so three divisions past the mark is 3 × 20 = 60 g. Adding this to the 400 g mark gives 400 + 60 = 460 g. Treating each division as worth 1 g instead of 20 g gives 400 + 3 = 403 g. Working out the extra amount correctly but forgetting to add the 400 g mark gives just 60 g. Treating each division as worth 10 g instead of 20 g gives 400 + 30 = 430 g.
- (b) 320° — A bearing is always measured clockwise from north. An angle measured anticlockwise must be converted by subtracting it from 360°: 360 − 40 = 320°, so the bearing is 320°. Choosing 040° treats the anticlockwise angle as if it were already a clockwise bearing, without converting it. Choosing 220° adds 180° to the angle, mixing this up with a back-bearing calculation (40 + 180 = 220). Choosing 400° adds the angle to 360° instead of subtracting it (40 + 360 = 400), giving a bearing greater than a full turn.
- (a) 118° — When two straight lines cross, the angles that are vertically opposite each other are always equal. So the angle vertically opposite 118° is also 118°. A candidate who instead finds the angle next to it on the straight line, using 180° − 118° = 62°, has found the adjacent angle, not the vertically opposite one. A candidate who answers 180° has confused the rule with angles on a straight line. A candidate who doubles the angle, giving 236°, has applied no valid angle rule at all. The vertically opposite angle is 118°.
- (c) 27 cm² — Area of a rectangle = length × width = 4.5 × 6 = 27 cm². A pupil who adds the two sides instead of multiplying gets 4.5 + 6 = 10.5 cm². A pupil who works out the perimeter instead of the area gets 2 × (4.5 + 6) = 21 cm². A pupil who rounds 4.5 up to 5 before multiplying gets 5 × 6 = 30 cm². The correct area is 27 cm².
- (d) 42.4 cm² — Sector area = (angle ÷ 360) × π × r². First, 60 ÷ 360 = 1/6. Next, π × r² = 3.14 × 81 = 254.34 cm². So the area = (1/6) × 254.34 = 42.39 cm², which rounds to 42.4 cm². (4.7 cm² comes from forgetting to square the radius: using π × r = 3.14 × 9 = 28.26, then (1/6) × 28.26 = 4.71 cm²; 254.3 cm² comes from finding the area of the whole circle, 254.34 cm², and forgetting the angle fraction; 9.4 cm² comes from using the arc length formula instead: 2 × π × r = 2 × 3.14 × 9 = 56.52 cm, then (1/6) × 56.52 = 9.42 cm.)
- (a) £157.00 — Area covered = (angle ÷ 360) × π × r² = (90 ÷ 360) × 3.14 × 400 = 0.25 × 1256 = 314 km². Charge = 314 × £0.50 = £157.00. (£7.85 comes from forgetting to square the radius, using 0.25 × 3.14 × 20 = 15.7 km² and then charging that; £628.00 comes from finding the area of a full circle, 3.14 × 400 = 1256 km², and forgetting the angle fraction before charging; £15.70 comes from using the arc length formula, 0.25 × 2 × 3.14 × 20 = 31.4, in place of the area, and charging that.)
- (d) 1535 cm² — The wiper sweeps out a sector of radius 40 cm, the blade length, through an angle of 110°. Sector area is angle ÷ 360 × π × radius²: 110 ÷ 360 × 3.14 × 1600 = 1535.1 cm², which rounds to 1535 cm². Forgetting to square the radius, using radius instead of radius², gives 38 cm². Using 110 ÷ 180 instead of 110 ÷ 360 for the fraction gives 3070 cm². Treating the 40 cm blade length as a diameter, so using a radius of 20 cm, gives 384 cm².
- (a) 6 — A cuboid has six faces in total: a top, a bottom, a front, a back, and two ends — each one is a rectangle in the net, giving six rectangles altogether. Choosing 3 counts only the three PAIRS of congruent rectangles (top/bottom, front/back, two ends) rather than all six individual faces. Choosing 5 forgets one face, as if the net were missing its lid. Choosing 12 is the number of edges of a cuboid, not the number of rectangles in its net.
- (c) 6 cm — For a parallelogram, area = base × height, so height = area ÷ base = 54 ÷ 9 = 6 cm. 12 cm comes from using the triangle's reverse formula, height = 2 × area ÷ base, which does not apply to a parallelogram. 45 cm comes from subtracting the base from the area, 54 − 9, instead of dividing. 486 cm comes from multiplying the area by the base, 54 × 9, instead of dividing.
- (b) 10.5 — Method: multiply the drawing length by the scale factor to get the real length. Working: 7 cm × 1.5 = 10.5 m. A student who answers 8.5 has added the scale factor to the drawing length instead of multiplying (7 + 1.5). A student who answers 14 has rounded the scale factor up to 2 before multiplying. A student who answers 3.5 has divided the drawing length by 2 instead of multiplying it by 1.5. Answer: 10.5 m.
- (b) 18 — Method: convert the real length to centimetres, then divide by the scale factor to shrink it down to the model's size. Working: 4.32 m = 432 cm; 432 cm / 24 = 18 cm. A student who answers 432 has converted the units correctly but forgotten to divide by the scale factor at all. A student who answers 10368 has multiplied by the scale factor instead of dividing (432 x 24). A student who answers 1.8 has converted the metres to centimetres by multiplying by 10 instead of 100, getting 43.2 cm, and then divided by 24. Answer: 18 cm.
- (a) 24 — The display is 4 tins wide, 3 tins high and 2 tins deep, and every position in that block is filled, so the total number of tins is the product of all three measurements: 4 × 3 × 2 = 24. "12" comes from multiplying only the width and height shown in the front elevation (4 × 3), forgetting the depth entirely. "9" comes from adding the three measurements (4 + 3 + 2) instead of multiplying them. "6" comes from multiplying only the height and depth (3 × 2), forgetting the width shown by the front elevation.
- (d) 8.75 cm — The scale factor of the enlargement is 11.2 ÷ 3.2 = 3.5. Applying this to the second line, 2.5 × 3.5 = 8.75 cm. The distractor 10.50 cm comes from adding the difference between the first line's two lengths (11.2 − 3.2 = 8) to the second line's original length, 2.5 + 8 = 10.5. The distractor 0.71 cm comes from using the scale factor the wrong way round, 2.5 × (3.2 ÷ 11.2) = 0.71 (to 2 d.p.). The distractor 8.70 cm comes from directly subtracting 11.2 − 2.5 = 8.7, muddling the two different lines instead of scaling the second one.
- (c) 150 minutes — There are 60 minutes in an hour, so 2.5 hours is 2.5 × 60 = 150 minutes. Multiplying by 100 instead of 60, as if hours worked like a decimal metric unit, gives 250 minutes. Converting only the whole 2 hours and forgetting the extra 0.5 hours gives 120 minutes. Treating the 0.5 as 50 minutes, out of 100, instead of 30 minutes, out of 60, gives 170 minutes.
Build your own mix at the worksheet builder.