Printable · GCSE Foundation · ages 14-16
Geometry and measures worksheet — GCSE Foundation
Fifteen questions across the geometry and measures statements at Foundation tier. Choose the non-calculator filter to rehearse Paper 1, which counts for a third of the marks.
Calculator
Answer key: Geometry and measures worksheet — GCSE Foundation
MathsUKwww.geekhero.co.uk
- (d) 283 cm³ — Volume of a cylinder = πr²h. Using π = 3.14: V = 3.14 × 3² × 10 = 3.14 × 9 × 10 = 282.6, which rounds to 283 cm³. A pupil who uses the diameter, 6 cm, instead of the radius gets 3.14 × 6² × 10 = 1130.4 ≈ 1130 cm³. A pupil who forgets to square the radius gets 3.14 × 3 × 10 = 94.2 ≈ 94 cm³. A pupil who uses the circumference formula 2πr instead of πr² gets 2 × 3.14 × 3 × 10 = 188.4 ≈ 188 cm³. The correct volume is 283 cm³.
- (a) 65 — There are 10 millimetres in every centimetre, so to convert from cm to mm, multiply by 10: 6.5 × 10 = 65 mm. A candidate who forgets to convert at all writes down the original number, 6.5. A candidate who multiplies by 100 instead of 10, confusing cm-to-mm with m-to-cm, gets 650. A candidate who divides by 10 instead of multiplying gets 0.65. The correct length in millimetres is 65.
- (a) 33 — Method: total crates = (number of floor positions that actually have crates on them) × (the stack height). Working: there are 4 × 3 = 12 floor positions in the whole arrangement, but one corner position is left empty, leaving 11 filled positions; each filled position is stacked 3 crates high, so 11 × 3 = 33. Answer: 33. The distractors: 36 comes from forgetting to remove the empty corner and using all 12 positions (12 × 3). 35 comes from removing only one crate for the empty corner instead of the full stack of 3 (36 − 1). 11 comes from counting the filled floor positions and stopping there, forgetting that each one carries a stack 3 crates high.
- (c) 52° — When two straight lines cross, the angles opposite each other at the crossing point are vertically opposite and are equal. Ray OQ is opposite ray OP and ray OS is opposite ray OR, so angle QOS is vertically opposite angle POR. Therefore angle QOS = 52°.
- (b) 16.747 m³ — Volume of a sphere = (4/3)πr³, so a hemisphere is half that: (2/3)πr³. Substitute r = 2: (2/3) × 3.14 × 2³ = (2/3) × 3.14 × 8 = (2/3) × 25.12 = 16.7467 m³, which rounds to 16.747 m³.
- (b) Acute — An acute angle is any angle less than 90°. Since 47° is less than 90°, it is acute. An obtuse angle is between 90° and 180°, which 47° is not. A reflex angle is greater than 180°, which is far too big for 47°. A right angle is exactly 90°, not 47°. The angle is acute.
- (c) £7.85 — Arc length = (90 ÷ 360) × 2 × 3.14 × 10 = 0.25 × 62.8 = 15.7 cm. Cost = 15.7 × £0.50 = £7.85. (£31.40 comes from finding the full circumference and forgetting the angle fraction; £15.70 comes from using the diameter, 20 cm, in place of the radius; £157.00 comes from multiplying the arc length by the radius instead of by the cost per centimetre.)
- (c) 151,200 cm² — First find the area in m²: 4.2 × 3.6 = 15.12 m². To convert m² to cm², multiply by 10,000, since 1 m² = 100 cm × 100 cm = 10,000 cm²: 15.12 × 10,000 = 151,200 cm². 15.12 cm² gives the area in m² without converting the units at all. 1,512 cm² multiplies by 100 instead of 10,000, treating the conversion as if it were for a single length rather than an area. 15,120 cm² multiplies by 1,000 instead of 10,000.
- (a) 188.4 cm² — Curved surface area of a cone = πrl. With r = 6 cm, l = 10 cm and π = 3.14, curved surface area = 3.14 × 6 × 10 = 188.4 cm². A student who uses the cylinder's curved surface area formula, 2πrl, instead of the cone's gets 2 × 3.14 × 6 × 10 = 376.8 cm². A student who uses the circle-area formula πr² instead of πrl gets 3.14 × 36 = 113.04 cm². A student who multiplies r × l but leaves out π entirely gets 6 × 10 = 60 cm².
- (a) 75° — The three angles in the triangle formed by the two supports and the ground add up to 180°. Two of the angles are 34° and 71°, so the third angle is 180 − 34 − 71 = 75, which is 75°. 105° comes from adding the two given angles together instead of subtracting them from 180° (34 + 71 = 105). 146° comes from computing 180 − 34 = 146 and forgetting to also subtract 71°. 37° comes from subtracting the two given angles from each other instead of using the triangle's angle sum (71 − 34 = 37).
- (d) 18.8 cm — Arc length is a fraction of the full circumference. Here 120 ÷ 360 = 1/3, and the full circumference is 2 × 3.14 × 9 = 56.52 cm, so the arc is 56.52 ÷ 3 = 18.84 cm, which rounds to 18.8 cm. Forgetting the fraction and giving the full circumference rounds to 56.5 cm. Using 9 cm as a diameter instead of a radius gives an arc of 9.4 cm. Using 120 ÷ 180 instead of 120 ÷ 360 for the fraction gives an arc of 37.7 cm.
- (d) 7.7 m — The horizontal distance is adjacent to the 50° angle and the zip wire is the hypotenuse, so horizontal distance = 12 × cos 50° = 12 × 0.6428... = 7.71...≈ 7.7 m. "9.2 m" uses the sine ratio instead of cosine, 12 × sin 50° = 9.19...≈ 9.2 m, which actually finds the vertical drop of the zip wire, not the horizontal distance. "15.7 m" comes from dividing by the sine ratio instead of multiplying by the cosine ratio, 12 ÷ sin 50° = 15.66...≈ 15.7 m, both the wrong operation and the wrong ratio. "12.0 m" simply uses the length of the zip wire itself as the horizontal distance, ignoring the angle of 50° altogether.
- (b) 320° — A bearing is always measured clockwise from north. An angle measured anticlockwise must be converted by subtracting it from 360°: 360 − 40 = 320°, so the bearing is 320°. Choosing 040° treats the anticlockwise angle as if it were already a clockwise bearing, without converting it. Choosing 220° adds 180° to the angle, mixing this up with a back-bearing calculation (40 + 180 = 220). Choosing 400° adds the angle to 360° instead of subtracting it (40 + 360 = 400), giving a bearing greater than a full turn.
- (d) 12.56 cm — Arc length = (angle ÷ 360) × 2 × π × r = (72 ÷ 360) × 2 × 3.14 × 10 = 0.2 × 62.8 = 12.56 cm. (62.8 cm comes from finding the full circumference and forgetting to take the angle fraction; 6.28 cm comes from leaving out the factor of 2, using πr instead of 2πr; 25.12 cm comes from using the diameter, 20 cm, in place of the radius.)
- (d) Yes, because 45 ÷ 360 = 1/8, and this fraction applies to any radius. — Priti is correct: 45 ÷ 360 = 1/8, and because sector area = (angle ÷ 360) × full circle area, this fraction depends only on the angle, not on the radius, so it holds for every circle. (The statement giving 45 ÷ 360 = 1/6 comes from an arithmetic slip when simplifying the fraction; the statement that the fraction depends on the radius is wrong because the radius cancels out of the angle fraction in the sector-area formula; the statement adding that it only works for this particular radius is wrong because the 1/8 fraction is true for every radius, not a special case.)
Build your own mix at the worksheet builder.