Printable · GCSE Foundation · ages 14-16
Geometry and measures worksheet — GCSE Foundation
Fifteen questions across the geometry and measures statements at Foundation tier. Choose the non-calculator filter to rehearse Paper 1, which counts for a third of the marks.
Non-calculator
Answer key: Geometry and measures worksheet — GCSE Foundation
MathsUKwww.geekhero.co.uk
- (b) The arcs only meet exactly on AB, not above or below it. — With a radius of exactly half of AB, the arc centred at A and the arc centred at B each reach precisely to the midpoint of AB, so they meet only at that one point, on the line AB itself — there are no two intersection points above and below the line to join, so the perpendicular bisector cannot be drawn. (The claim that this radius is always too short to draw any arc is wrong, since a radius equal to half of AB is a perfectly valid, positive length for a compass arc; the claim that the radius must equal the full length of AB is wrong — a longer radius than half of AB would also work, it does not have to equal AB exactly; the claim that the arcs would not cross line AB at all is wrong, since they do cross it — that is exactly the problem, they meet only on it.)
- (c) 1/2 — sin 45° = √2/2 and cos 45° = √2/2, so sin 45° × cos 45° = √2/2 × √2/2 = 2/4 = 1/2. √2/2 comes from writing down only one of the two factors and forgetting to multiply by the other. √2 comes from adding the two exact values instead of multiplying them: √2/2 + √2/2 = √2. 1 comes from wrongly treating sin 45° × cos 45° as sin(45° + 45°) = sin 90° = 1 — multiplying two ratios is not the same as adding their angles.
- (b) (−1, −2) — To translate R(−6, 9) by $\binom{5}{−11}$, add 5 to the x-coordinate and −11 to the y-coordinate: (−6 + 5, 9 + (−11)) = (−1, −2). (−1, 9) applies only the x-component and leaves the y-coordinate unchanged. (−6, −2) applies only the y-component and leaves the x-coordinate unchanged. (−11, 20) comes from subtracting the vector instead of adding it.
- (b) $\binom{8}{3}$ — The column vector is (end − start) in each coordinate: (9 − 1, 4 − 1) = (8, 3), written as $\binom{8}{3}$. $\binom{3}{8}$ swaps the horizontal and vertical components. $\binom{10}{5}$ comes from adding the coordinates instead of subtracting them. $\binom{−8}{−3}$ comes from working out start minus end instead of end minus start.
- (d) a rectangle — The shed is a prism, so its two triangular ends are identical and parallel, a fixed distance apart along the shed's length; the floor they stand on is therefore bounded by the base of one triangle, the base of the other, and the two straight edges joining them — a rectangle. Looking straight down, the sloping roof projects onto that same rectangle rather than outside it, so the plan view is a plain rectangle, as long as the shed and as wide as its gable end. "a triangle" is the shape of the END wall, seen from the front or back, not from above. "a triangle with a rectangle attached" wrongly combines a side-elevation feature with the plan — the plan does not show the triangular end wall at all, since looking down hides it completely. "two triangles joined at their bases" describes neither the plan nor any single elevation of this shed.
- (a) Square — Method: two conditions are being asked for at once, so test each shape against both — the two diagonals must always be the same length as each other, and they must always meet at 90°. Working: in a rectangle the diagonals are equal but they meet at 90° only in the special case where the rectangle is also a rhombus; in a rhombus the diagonals do meet at 90° but they are of different lengths unless the rhombus is also a rectangle; the shape that satisfies both conditions for every example of it is the one that is both, and its diagonals are equal and perpendicular. Answer: the square. The distractors: the rectangle is where a candidate stops who tests only the equal-length condition and never checks the angle at the crossing; the rhombus is where a candidate stops who tests only the right-angle condition and never checks the two lengths; the parallelogram is chosen by a candidate who remembers that the diagonals of a parallelogram bisect each other and treats bisecting each other as being equal to each other, which is a different property.
- (b) 13 — Method: the straight-line distance between two points on a grid is the hypotenuse of a right-angled triangle whose shorter sides are the horizontal gap and the vertical gap between them, so Pythagoras' theorem applies. Working: one point is the origin, so the horizontal gap is 5 and the vertical gap is 12. Then d² = 5² + 12² = 25 + 144 = 169, so d = √169 = 13. Answer: 13. The distractors: 17 comes from adding the two gaps, 5 + 12, instead of adding their squares and taking the root; 12 comes from reading off the vertical gap alone and offering that as the whole distance; 7 comes from subtracting the gaps, 12 − 5, as though a distance were a difference.
- (b) 72 000 cm³ — Cross-sectional area = 1/2 × 40 × 30 = 600 cm². Volume = cross-sectional area × length = 600 × 120 = 72 000 cm³. (144 000 cm³ comes from forgetting the 1/2 in the triangle's area, using 40 × 30 as the cross-section; 36 000 cm³ comes from halving the correct volume again, as if the 1/2 applied a second time; 720 cm³ comes from adding the cross-sectional area and the length, 600 + 120, instead of multiplying them.)
- (b) Right angle, equal hypotenuse, one more side — RHS requires a right angle in each triangle, equal hypotenuses, and one further pair of equal sides, so 'right angle, equal hypotenuse, one more side' is correct. 'Right angle, hypotenuse, one more angle' is wrong because it asks for an extra equal angle instead of an extra equal side, which RHS does not check. 'Two sides and the angle between them' describes SAS, not RHS, so it is wrong. 'Right angle and all three sides equal' describes SSS with an extra right-angle condition, asking for more information than RHS actually needs, so it is wrong.
- (c) 6 squares — Method: the plan view shows the footprint of the solid; a second layer stacked on top of floor positions that are already covered does not create any new squares in the plan. Working: the row of 4 cubes and the row of 2 cubes attached at the end do not overlap, so the footprint has 4 + 2 = 6 distinct squares. Answer: 6 squares. The distractors: 12 squares comes from counting the total number of cubes used, including the second layer (6 floor positions × 2 layers = 12), instead of the footprint. 4 squares comes from counting only the row of four and forgetting the attached row of two. 5 squares comes from wrongly treating the corner square as shared between the two rows (4 + 1 instead of 4 + 2).
- (b) 6√3 m — The horizontal distance covered by one support is adjacent to the 30° angle, so it equals 6 × cos 30° = 6 × √3/2 = 3√3 m. The total base width is made up of both supports, so it is 2 × 3√3 = 6√3 m. '3√3 m' gives only one support's horizontal distance and forgets to double it for the total width. '6 m' comes from using sin 30° instead of cos 30° for the horizontal distance (6 × sin 30° = 3, doubled to 6). '12 m' comes from doubling the full sloping length of 6 m without using any trigonometry at all.
- (a) 6 cm — Method: a diameter runs right across a circle through its centre, so it is made of two radii laid end to end, which gives diameter = 2 × radius. Working: the radius is 3 cm, so the diameter is 2 × 3 = 6 cm. Answer: 6 cm. The distractors: 1.5 cm comes from dividing by 2 instead of multiplying by it, which is the relationship applied in the wrong direction; 3 cm comes from copying the radius straight down, treating the two words as names for the same measurement; 5 cm comes from adding 2 to the radius instead of multiplying the radius by 2.
- (c) ABC ≅ XYZ — Method: match each vertex in ABC to its corresponding vertex in XYZ, using the equal sides and angles given, then write the letters in that matching order. Working: AB matches XY, BC matches YZ, and angle B matches angle Y, so A corresponds to X, B corresponds to Y, and C corresponds to Z, giving ABC ≅ XYZ. Options: 'ABC ≅ ZYX' puts Z in A's position, but A corresponds to X, not Z; 'ABC ≅ YXZ' puts Y in A's position, but A corresponds to X; 'ABC ≅ ZXY' puts Z in A's position and X in B's position, neither of which is correct. Answer: ABC ≅ XYZ.
- (b) (5, 1) — First scale a by 2: 2a = (2×3, 2×(−2)) = (6, −4). Then add b component by component: (6+(−1), −4+5) = (5, 1). (2, 3) is a + b without doubling a first. (4, 6) doubles both a and b instead of only a. (7, −9) subtracts b from 2a instead of adding it.
- (b) tan 90° — Method: write each ratio as one side of a right-angled triangle divided by another, and look for the one whose bottom line can be zero. Working: sine and cosine are both a side divided by the hypotenuse, and a hypotenuse is never zero, so sin 90° = 1 and cos 90° = 0 are both perfectly good values — a value of zero is still a value. Tangent is the opposite side divided by the adjacent side. As the angle opens out towards 90° the adjacent side shrinks to nothing, and a division by zero has no result, while at the other end of the row the adjacent side is the long one and tan 0° = 0. Answer: tan 90°.
Build your own mix at the worksheet builder.