Printable · GCSE Foundation · ages 14-16
Geometry and measures worksheet — GCSE Foundation
Fifteen questions across the geometry and measures statements at Foundation tier. Choose the non-calculator filter to rehearse Paper 1, which counts for a third of the marks.
Answer key: Geometry and measures worksheet — GCSE Foundation
MathsUKwww.geekhero.co.uk
- (b) 16.747 m³ — Volume of a sphere = (4/3)πr³, so a hemisphere is half that: (2/3)πr³. Substitute r = 2: (2/3) × 3.14 × 2³ = (2/3) × 3.14 × 8 = (2/3) × 25.12 = 16.7467 m³, which rounds to 16.747 m³.
- (d) sector — The region enclosed by two radii and the arc between them is called a sector. A segment is a different region, enclosed by a CHORD and an arc — it does not touch the centre at all. A chord is a straight line, not a region, so it cannot be the answer to a question asking for a region. A semicircle is only correct when the angle between the two radii is exactly 180°, which is not stated here, so it is too specific to be the general answer.
- (a) A smaller circle — Since the cutting plane is parallel to the circular base, the cross-section is also a circle, but smaller than the base because the cone narrows as it rises towards the apex, so 'a smaller circle' is correct. 'A triangle' wrongly describes the outline seen from the side of the cone, not a horizontal cross-section. 'An ellipse' would only result from a cut made at an angle to the base, not one parallel to it. 'The same size circle as the base' wrongly ignores that the cone tapers, so any parallel cross-section above the base must be smaller.
- (d) 63.6 — Method: the three angles inside the triangle formed by the two ladders and the ground add up to 180°. Working: 180 − 58.2 − 58.2 = 63.6. Answer: 63.6°. A candidate who assumes the top angle equals the base angles gives 58.2. A candidate who subtracts only one base angle from 180°, working out 180 − 58.2, gets 121.8. A candidate who doubles the base angle instead of subtracting it twice from 180°, working out 2 × 58.2, gets 116.4.
- (d) 21 cm — The scale factor from triangle ABC to triangle PQR is PQ ÷ AB = 15 ÷ 5 = 3. QR = BC × scale factor = 7 × 3 = 21 cm. A student who divides BC by the scale factor instead of multiplying gets 7 ÷ 3 = 2.33 cm. A student who multiplies BC by AB instead of by the scale factor gets 7 × 5 = 35 cm.
- (a) 5/12 — A sector's area is always the same fraction of the circle as its angle is of the full 360° turn. Here that fraction is 150 out of 360, which simplifies (divide both numbers by 30) to 5/12. Treating a full turn as 180° instead of 360° gives 5/6. Confusing the 150° given with the 180° of a half turn gives 1/2. Working out the fraction OUTSIDE the sector instead of inside it gives 7/12.
- (d) Yes, by the AA condition — Method: similarity is decided by the angles, and because the three angles of a triangle add up to 180°, two matching pairs force the third pair to match as well. Working: the angles at A and D are both 40° and the angles at B and E are both 70°, so the third angles are both 180° − 40° − 70° = 70° and all three pairs are equal. Two pairs were enough, and that is the AA condition. Answer: yes, by the AA condition. The distractors: 'Yes, by the SSS condition' names a condition about three pairs of sides in proportion, and the question gives no side lengths at all; 'No, because no side lengths are given' treats side information as necessary, which it is for congruence but not for similarity; 'No, because the triangles may be different sizes' turns the definition of similarity into an objection, since similar figures are allowed to differ in size and only their shape must match.
- (a) 150° — The arc length is the same fraction of the circumference as the angle is of 360°. The full circumference is 2 × 3.14 × 6 = 37.68 cm, so the angle is 15.7 ÷ 37.68 × 360 = 150°. Treating the 6 cm as a diameter instead of a radius gives a circumference of 18.84 cm and an angle of 300°. Using π = 3 instead of the given 3.14 gives a circumference of 36 cm and an angle of 157°. Treating the fraction 15.7 ÷ 37.68 as being out of 100 rather than 360 gives about 42°.
- (a) 110° — The truss is isosceles, so its two base angles are equal; since the three angles of the triangle add up to 180° and the apex is 40°, each base angle is (180 − 40) ÷ 2 = 70°. The angle between the sloping edge and the joist, extended beyond the base of the truss, sits on a straight line with that 70° base angle, and angles on a straight line add up to 180°, so the required angle is 180 − 70 = 110°. "70°" comes from stopping after finding the base angle and giving it directly, without also using the straight-line fact to find the angle on the OUTSIDE of the truss. "140°" comes from doubling the base angle instead of using the straight-line fact. "20°" comes from taking half of the apex angle (40° ÷ 2), mistaking it for the required angle instead of properly using the triangle's angle sum.
- (c) 18 — Rearranging F + V − E = 2 gives E = F + V − 2. Substitute F = 8 and V = 12: 8 + 12 − 2 = 18 edges. Choosing 20 comes from adding the faces and vertices but forgetting to subtract the 2 (8 + 12 = 20). Choosing 22 comes from adding the 2 instead of subtracting it (8 + 12 + 2 = 22). Choosing 16 comes from subtracting 2 twice by mistake (8 + 12 − 2 − 2 = 16).
- (d) The angle between a tangent and a radius is 90° — OP is the radius drawn to the point of contact P, and a circle theorem states that a tangent always meets that radius at a right angle, so angle OPQ = 90°. A tangent is not parallel to the radius it touches — at the point of contact it is perpendicular to that radius, not parallel to it. A tangent does not pass through the centre — a straight line through the centre that also touches the circle at one point would have to be a diameter, which is a different line entirely. The angle-in-a-semicircle theorem needs a triangle drawn inside the circle with a diameter as its longest side; there is no such triangle here, just a tangent and a radius.
- (b) 12.56 cm² — Sector area = (angle ÷ 360) × π × r² = (90 ÷ 360) × 3.14 × 4² = 0.25 × 3.14 × 16 = 12.56 cm². (3.14 cm² comes from forgetting to square the radius; 50.24 cm² comes from finding the area of the whole circle and forgetting the angle fraction; 6.28 cm² comes from using the arc length formula instead of the sector area formula.)
- (d) 4.44 m — The real van's length is 18.5 × 24 = 444 cm, which converts to 4.44 m. '0.77 m' comes from dividing by 24 instead of multiplying, using the ratio the wrong way round (18.5 ÷ 24 = 0.77 cm), and then writing that figure down as metres. '44.4 m' comes from converting 444 cm to metres with the decimal point in the wrong place. '444 m' comes from working out 444 cm correctly but forgetting to convert it into metres at all.
- (b) 12 m — sin 30° = opposite ÷ hypotenuse, where the opposite side is the height (6 m) and the hypotenuse is the string. So string = height ÷ sin 30° = 6 ÷ (1/2) = 12 m. The distractor 3 m comes from multiplying by sin 30° instead of dividing (6 × 1/2 = 3). The distractor 6√3 m comes from using tan 30° = 1/√3 instead of sin 30° (6 ÷ (1/√3) = 6√3). The distractor 4√3 m comes from using cos 30° = √3/2 instead of sin 30° (6 ÷ (√3/2) = 12/√3 = 4√3).
- (a) 7.2 cm — The distance around the mat is the circumference, π × diameter = 3.14 × 20 = 62.8 cm. Yasmin started with 70 cm, so the ribbon left over is 70 − 62.8 = 7.2 cm. 62.8 cm is the circumference itself, the amount of ribbon used, not what is left over. 50 cm comes from subtracting the diameter instead of the circumference: 70 − 20 = 50. 20 cm is simply the diameter of the mat and involves no calculation with the ribbon length at all.
Build your own mix at the worksheet builder.