Printable · GCSE Higher · ages 14-16
Measuring, scale drawings and bearings worksheet — GCSE Higher
Fifteen questions on "measuring, scale drawings and bearings" — DfE statement G15. Print it, or print three versions so neighbours cannot copy by letter; the key gives the letter for each version.
Measuring, scale drawings and bearings worksheet — GCSE Higher
MathsUKwww.geekhero.co.uk
- 1.The angle between north and a footpath is 35°, measured clockwise from north. What is the three-figure bearing of the footpath?
- 2.A map has a scale of 1 : 20 000. The distance between two villages is 3.4 km in real life. How long is this distance on the map, in centimetres?
- 3.Two straight paths cross at a junction in a park. One of the angles between them, measured with a protractor, is 76°. What is the size of the angle immediately next to it on a straight line?
- 4.A hiker starts by walking on a bearing of 245°. She turns clockwise through 50°, then turns clockwise through a further 15°, and continues walking in a straight line. What bearing is she now walking on?
- 5.The bearing of a harbour B from a ferry's position A is 260°. What is the bearing of A from B?
- 6.A garden plan is drawn to a scale of 1 cm : 1.8 m. A path on the plan measures 4.5 cm. What is the real length of the path, in metres, to 1 decimal place?
- 7.A plan of a school hall uses a scale of 1 : 250. A wall is drawn 3.4 cm long on the plan. Sam wants to know the wall's real length in metres. What is it?
- 8.The bearing of a campsite B from a walker's position A is 070°. What is the bearing of A from B?
- 9.A scale drawing shows a room that is 5 cm wide. The real room is 15 m wide. Write the scale of the drawing in the form 1 : n.
- 10.A plan of a car park is drawn to a scale of 1 : 500. A parking bay is drawn as a rectangle measuring 1.2 cm by 0.6 cm. The real width of the bay corresponds to the 0.6 cm side. What is the real width of the bay, in metres?
- 11.A scale drawing uses a scale of 1 : 60. A path on the drawing is measured as 9.8 cm long. What is the real length of the path, in metres, to 1 decimal place?
- 12.A scale drawing of a bridge uses a scale of 1 : 25. A support beam on the drawing measures 4.4 cm. What is the real length of the beam, in metres?
- 13.A hiker walks on a bearing of 065°. She then turns clockwise through 90° and continues walking in a straight line. What bearing is she now walking on?
- 14.Two straight roads cross at a junction. The angle between them, measured with a protractor, is 118°. What is the size of the angle vertically opposite to it?
- 15.A scale drawing of a park uses a scale of 1 : 2000. A path is drawn 8.5 cm long on the drawing. A cyclist rides the length of the path and then rides straight back again along the same path. How far does the cyclist travel in total, in metres?
Answer key
- (a) 035° — A bearing is measured clockwise from north, so an angle of 35° clockwise from north is a bearing of 035° (written with three figures). Choosing 325° measures the angle anticlockwise instead of clockwise (360 − 35 = 325). Choosing 215° adds 180° to the angle, mixing this up with a back-bearing calculation (35 + 180 = 215). Choosing 350° reorders the digits of 035, writing the ones digit before the tens digit by mistake.
- (a) 17 cm — Convert the real distance to centimetres first: 3.4 km = 340 000 cm. Then divide by the scale factor, 20 000, since the map is 20 000 times smaller than real life: 340 000 ÷ 20 000 = 17, so the map distance is 17 cm. Choosing 1700 cm divides by 200 instead of 20 000, losing two zeros from the scale factor (340 000 ÷ 200 = 1700). Choosing 170 cm divides by 2 000 instead of 20 000, losing one zero from the scale factor (340 000 ÷ 2 000 = 170). Choosing 0.17 cm divides by 2 000 000 instead of 20 000, adding two extra zeros to the scale factor (340 000 ÷ 2 000 000 = 0.17).
- (b) 104 — Method: angles on a straight line add up to 180°. Working: 180° − 76° = 104°. A student who answers 76 has mistaken this for the vertically opposite angle, which is equal, rather than the adjacent angle on a straight line. A student who answers 90 has wrongly assumed the two paths must be perpendicular. A student who answers 14 has subtracted 76° from 90° instead of from 180°. Answer: 104°.
- (d) 310 — Method: since both turns are clockwise, add both angles to the starting bearing. Working: 245° + 50° = 295°; 295° + 15° = 310°. A student who answers 295 has only added the first turn and forgotten the second one. A student who answers 180 has subtracted both turns instead of adding them. A student who answers 320 has added the two turns as 75° instead of 65° by misreading the second turn. Answer: 310°.
- (a) 080° — The back bearing differs from the given bearing by 180°. Because 260° is greater than 180°, subtract 180°: 260 − 180 = 80°, so the bearing of A from B is 080°. Choosing 440° adds 180° instead of subtracting it, even though the result would be more than a full turn (260 + 180 = 440). Choosing 180° assumes the back bearing is always exactly 180°, ignoring the original bearing altogether. Choosing 100° comes from measuring the reflex angle the other way round the circle (360 − 260 = 100) instead of applying the 180° back-bearing rule.
- (a) 8.1 m — Multiply the length on the plan by the scale factor: 4.5 × 1.8 = 8.1, so the real length is 8.1 m. Choosing 6.3 m adds the two numbers instead of multiplying them (4.5 + 1.8 = 6.3). Choosing 2.5 m divides the plan length by the scale factor the wrong way round (4.5 ÷ 1.8 = 2.5) instead of multiplying. Choosing 9.0 m rounds the scale factor up to 2 before multiplying (4.5 × 2 = 9.0), losing the accuracy the 1.8 was giving.
- (b) 8.5 m — First apply the scale to convert the plan length to a real length in centimetres: 3.4 × 250 = 850 cm. Then convert centimetres to metres by dividing by 100: 850 ÷ 100 = 8.5, so the wall is 8.5 m long. Choosing 850 m applies the scale correctly but forgets to convert the answer from centimetres into metres. Choosing 0.85 m divides by 1000 instead of 100, confusing the centimetre-to-metre conversion with a metre-to-kilometre one. Choosing 3.4 m ignores the scale factor completely and just restates the plan length as if it were already the real length.
- (a) 250° — The back bearing (the bearing of A from B) differs from the bearing of B from A by exactly 180°. Because the given bearing, 070°, is less than 180°, add 180°: 070 + 180 = 250°, so the bearing of A from B is 250°. Choosing 180° assumes the back bearing is always exactly 180°, ignoring the original bearing altogether. Choosing 110° comes from subtracting 180° from 070° and dropping the negative sign (070 − 180 = −110) instead of adding 180°. Choosing 160° comes from adding only 90° instead of 180° (070 + 90 = 160).
- (c) 1 : 300 — First convert both lengths to the same unit: 15 m = 1500 cm. The scale compares 5 cm on the drawing to 1500 cm in real life, so dividing both parts by 5 gives a scale of 1 : 300. A candidate who compares 5 to 15 without converting units gets 1 : 3. A candidate who converts 15 m to 150 cm, using the wrong conversion factor, gets 1 : 30. A candidate who converts 15 m to 15000 cm, again using the wrong conversion factor, gets 1 : 3000. The scale of the drawing is 1 : 300.
- (b) 3 — The real width is 0.6 × 500 = 300 cm, which converts to 3 m by dividing by 100. A candidate who uses the wrong side of the rectangle, 1.2 cm, instead of the 0.6 cm width, gets 1.2 × 500 = 600 cm = 6 m. A candidate who multiplies correctly but converts the 300 cm to metres by dividing by 1000 instead of 100 gets 0.3 m. A candidate who converts by dividing by 10 instead of 100 gets 30 m. The real width of the bay is 3 m.
- (a) 5.9 — The real length is 9.8 × 60 = 588 cm. Converting to metres, by dividing by 100, gives 5.88 m, which rounds to 5.9 m to 1 decimal place. A candidate who rounds 5.88 down instead of up gets 5.8 m. A candidate who forgets to convert from centimetres to metres gets 58.8. A candidate who divides by 60 instead of multiplying gets 0.16, to 2 decimal places. The real length, to 1 decimal place, is 5.9 m.
- (d) 1.1 — Method: multiply the drawing length by the scale factor to get the real length, then convert to the units asked for. Working: 4.4 cm × 25 = 110 cm = 1.1 m. A student who answers 4.4 has forgotten to use the scale at all. A student who answers 110 has correctly worked out the real length in centimetres but forgotten to convert it to metres. A student who answers 11 has used a scale factor of 2.5 instead of 25 by misreading the scale. Answer: 1.1 m.
- (c) 155° — Turning clockwise adds to the bearing. Starting on a bearing of 065° and turning clockwise through 90° gives 065° + 90° = 155°. A candidate who instead subtracts, working out 90° − 65° = 25°, has performed the wrong operation, giving 025°. A candidate who turns anticlockwise instead of clockwise works out 065° − 90°, which gives a negative number, and adding 360° to fix this gives 335° — the bearing for turning the other way. A candidate who thinks turning does not change the bearing at all keeps the answer as 065°. The new bearing, turning clockwise, is 155°.
- (a) 118° — When two straight lines cross, the angles that are vertically opposite each other are always equal. So the angle vertically opposite 118° is also 118°. A candidate who instead finds the angle next to it on the straight line, using 180° − 118° = 62°, has found the adjacent angle, not the vertically opposite one. A candidate who answers 180° has confused the rule with angles on a straight line. A candidate who doubles the angle, giving 236°, has applied no valid angle rule at all. The vertically opposite angle is 118°.
- (b) 340 — The real length of the path is 8.5 × 2000 = 17000 cm, which converts to 170 m by dividing by 100. The cyclist rides the path there and back, so the total distance is 170 × 2 = 340 m. A candidate who forgets the return journey gives only the one-way distance, 170 m. A candidate who halves the one-way distance instead of doubling it, reading “there and back” as splitting the journey, gets 85 m. A candidate who doubles the scale factor to 4000 by mistake, getting a one-way length of 340 m, and then doubles that for the return journey, gets 680 m. The total distance the cyclist travels is 340 m.
Build your own mix at the worksheet builder.