Printable · GCSE Higher · ages 14-16
Geometry and measures worksheet — GCSE Higher
Fifteen questions across the geometry and measures statements at Higher tier. Choose the non-calculator filter to rehearse Paper 1, which counts for a third of the marks.
Non-calculator
Geometry and measures worksheet — GCSE Higher
MathsUKwww.geekhero.co.uk
- 1.Which of these statements about solving a triangle is correct?
- 2.An isosceles trapezium has exactly one pair of parallel sides, and its two non-parallel sides are equal in length. How many lines of symmetry does it have?
- 3.Two triangular offcuts of wood, PQR and STU, are cut for a construction project. PQ = 8 cm, QR = 6 cm and angle PQR = 90°. ST = 8 cm, TU = 6 cm and angle STU = 90°. A carpenter wants to check the two pieces are identical in shape and size before using them as a matching pair. Using only the measurements given, and without working out any further lengths, which condition proves that triangle PQR is congruent to triangle STU?
- 4.A quadrilateral has both pairs of opposite sides parallel and equal in length, but none of its angles are right angles. Which statement about this quadrilateral is correct?
- 5.A rectangular notice board measures 150 cm by 80 cm. Work out its area in m².
- 6.A tile is described as having two pairs of parallel sides, four equal sides, and diagonals that cross at right angles but are not equal in length. Give a reason why this tile cannot be a square.
- 7.A ferris wheel's circular frame has centre O. A support strut runs from O to a point A on the rim, and a second strut runs from O to point B on the rim, with angle AOB = 76°. A cabin is mounted at point C on the major arc AB, and D is a separate point on the minor arc AB. Work out the difference between angle ACB and angle ADB.
- 8.A drone flies from its base in three stages, each stage measured in metres east and north as a column vector. Stage 1 is the column vector with top number 30 and bottom number 40. Stage 2 is the column vector with top number −10 and bottom number 20. Stage 3 is the column vector with top number 15 and bottom number −5. Work out the column vector that would take the drone in a single straight flight back to its base from where it ends up.
- 9.A shop stacks tins in a display block. The front elevation of the block is 4 tins wide and 3 tins high. The side elevation shows the block is 2 tins deep. Every position in the block is filled. How many tins are used in total?
- 10.Triangle ABC has AB = 6 cm and BC = 9 cm, with angle A = 40°. Triangle DEF has DE = 6 cm and EF = 9 cm, with angle D = 40°. Meera says these facts prove the triangles are congruent by SAS. Is Meera correct?
- 11.A circle with centre O has radius 17 cm. A chord AB is drawn so that the perpendicular distance from O to AB is 8 cm. Work out the length of the chord AB.
- 12.Triangle T has a vertex A at (4, 6). It is enlarged by a scale factor of −1/2, centre (2, 2). Work out the coordinates of the image of point A.
- 13.In triangle OAB, OA = a and OB = b. P lies on AB such that AP is twice PB. Express the vector OP in terms of a and b.
- 14.A rectangular photograph has an area of 96 cm². One of its sides is 8 cm long. Work out the length of the other side.
- 15.Triangle ABC has AB = 10 cm, BC = 7 cm and angle A = 40°. Triangle DEF has DE = 10 cm, EF = 7 cm and angle D = 40°. Sam says the two triangles are congruent by SAS. Which statement about Sam's claim is correct?
Answer key
- (d) Two angles and a side: sine rule finds other sides. — Method: match the data you are given to the rule that needs it. Working: the sine rule a/sin A = b/sin B = c/sin C needs a complete angle-side pair to set up its ratio, so the statement that two angles and a side (AAS or ASA) let the sine rule find the other sides is the correct one — the third angle comes from the angle sum, and each unknown side is then opposite a known angle. The statement that two sides and the angle between them (SAS) call for the sine rule is wrong: no angle-side pair is complete, so the cosine rule is what works there. The statement that the sine rule finds any angle from three sides (SSS) is wrong for the same reason in reverse — no angle is known at all, so the cosine rule must find the first one. The statement that the cosine rule finds a missing angle directly from two sides and a non-included angle (SSA) is wrong: the cosine rule reports the angle enclosed by the two sides it uses, so with SSA it is the sine rule that reaches the missing angle, and the ambiguous case is then settled from the wording of the question.
- (d) 1 — An isosceles trapezium has one line of symmetry, running through the midpoints of the two parallel sides. 0 would be true for a scalene trapezium, whose non-parallel sides are unequal, but this trapezium's non-parallel sides are equal, so it is symmetrical. 2 is the number of lines of symmetry of a rectangle, not a trapezium. 4 comes from wrongly applying the 'number of sides equals number of lines of symmetry' rule, which only holds for REGULAR polygons — a trapezium is not regular.
- (b) SAS (two sides and the included angle) — PQ = ST and QR = TU are two pairs of matching sides, and the angle between them (angle Q and angle T) is 90° in both triangles — two sides and the angle between them are equal, so the triangles are congruent by SAS, using only the measurements given. RHS needs the hypotenuses to be known equal; here only the two legs are given, so you would first have to work out each hypotenuse by Pythagoras' theorem — extra working the question rules out. SSS has the same problem: the third side of each triangle is not given, only calculable. ASA needs two angles and the side between them, but here it is two sides and the angle between them that are given, not two angles.
- (c) It is a parallelogram but not a rectangle — Method: match the given properties to the definition of each named quadrilateral. Working: having both pairs of opposite sides parallel and equal in length is exactly the definition of a parallelogram; since none of the angles are right angles, it cannot also be a rectangle, which needs four right angles. Options: 'must be a rectangle' wrongly assumes every parallelogram has right angles; 'must be a rhombus' wrongly assumes equal opposite sides means all four sides are equal, but only the opposite pairs are stated as equal here; 'trapezium' is wrong because a trapezium has exactly one pair of parallel sides, while this shape has two pairs, so it is a parallelogram and not a trapezium. Answer: it is a parallelogram but not a rectangle.
- (d) 1.2 m² — Method: an area in square metres needs lengths in metres, so convert first and then multiply. Working: 100 cm = 1 m, so 150 cm = 1.5 m and 80 cm = 0.8 m, and the area = 1.5 × 0.8 = 1.2 m². Answer: 1.2 m². The same result comes from working in centimetres: 150 × 80 = 12 000 cm², and a square metre is a square of side 100 cm, so 100 × 100 = 10 000 cm² make one square metre and 12 000 ÷ 10 000 = 1.2. Dividing the 12 000 cm² by 100 instead, as though a square metre held only 100 square centimetres, gives 120 m²; dividing by 1000 gives 12 m². Working out the perimeter rather than the area gives 1.5 + 0.8 + 1.5 + 0.8 = 4.6, which is a length and not an area.
- (a) A square's diagonals are equal in length — A square has two pairs of parallel sides, four equal sides, and diagonals that are equal in length and cross at right angles. This tile's diagonals are not equal, so it is a rhombus that is not a square.
- (a) 104° — Method: find each inscribed angle separately using the angle-at-the-centre theorem: for a point on the arc NOT cut off by the given central angle, halve that central angle; for a point on the OTHER arc, halve the REFLEX central angle instead; then subtract the smaller from the larger. Working: for C on the major arc, angle ACB = 76 ÷ 2 = 38 degrees. For D on the minor arc, D sees the reflex angle at the centre, 360 − 76 = 284 degrees, so angle ADB = 284 ÷ 2 = 142 degrees. The difference is 142 − 38 = 104 degrees. Answer: 104°. Both inscribed angles need the theorem applied separately, using the correct arc's central angle each time (the reflex angle for D), and the question asks for the DIFFERENCE between the two, not either angle on its own and not their sum, 180°, which is simply the opposite-angle total for the cyclic quadrilateral ACBD.
- (c) (−35, −55) — Add the three stages component by component to find the drone's position relative to base: (30+(−10)+15, 40+20+(−5)) = (35, 55). The flight back to base is the negative of this vector, reversing both numbers: (−35, −55). (35, 55) is the vector from base to the drone's position — it forgets to reverse direction for the return flight. (−35, 55) only reverses the top number. (35, −55) only reverses the bottom number.
- (a) 24 — The display is 4 tins wide, 3 tins high and 2 tins deep, and every position in that block is filled, so the total number of tins is the product of all three measurements: 4 × 3 × 2 = 24. "12" comes from multiplying only the width and height shown in the front elevation (4 × 3), forgetting the depth entirely. "9" comes from adding the three measurements (4 + 3 + 2) instead of multiplying them. "6" comes from multiplying only the height and depth (3 × 2), forgetting the width shown by the front elevation.
- (b) No — the angle given is not the included angle — Method: check whether the given angle sits between the two given sides, since SAS requires the included angle. Working: sides AB and BC meet at vertex B, so the angle between them is angle B — but the angle given is angle A, which is not between the two given sides, and the same mismatch happens in triangle DEF. Options: 'two sides and one angle match' restates SAS's ingredients without checking their positions, which is exactly Meera's mistake; 'SSS needs three equal sides' is a true fact about a different condition, but it is not the reason Meera is wrong here; 'SAS allows any equal angle' states a rule that is not how SAS works, since the angle must be the included one. Answer: no, the angle given is not the included angle.
- (b) 30 cm — The perpendicular from the centre of a circle to a chord bisects the chord, so this line, half the chord and the radius form a right-angled triangle. Using Pythagoras' theorem, half the chord = √(17² − 8²) = √(289 − 64) = √225 = 15 cm. The full chord AB is twice this length: AB = 2 × 15 = 30 cm. Stopping after finding the half-chord, without doubling it for the whole chord, gives 15 cm. Adding the radius and the perpendicular distance directly, 17 + 8 = 25 cm, ignores that these two lengths are the two shorter sides of a right-angled triangle, not parts of a straight line. Subtracting instead, 17 − 8 = 9 cm, makes the same mistake in the other direction.
- (c) (1, 0) — To enlarge about a centre other than the origin, find the vector from the centre to the point, scale that vector, then add it back to the centre. The vector from (2, 2) to A(4, 6) is (2, 4). Scaling by −1/2 gives (−1, −2). Adding this to the centre (2, 2) gives the image point (1, 0). (3, 4) comes from using +1/2 instead of −1/2, so the image lands on the same side as A instead of the opposite side. (−2, −3) comes from scaling A's coordinates directly about the origin, ignoring that the centre is (2, 2). (−2, −6) comes from using a scale factor of −2 instead of −1/2.
- (c) (1/3)a + (2/3)b — Method: OP = OA + AP, and since AP is twice PB, AP is 2/3 of the whole of AB, with AB = b − a. Working: OP = a + 2/3(b − a) = a − (2/3)a + (2/3)b = (1/3)a + (2/3)b. Answer: OP = (1/3)a + (2/3)b. Measuring 2/3 of AB from B's end instead of A's swaps the fractions round, giving (2/3)a + (1/3)b; adding (2/3)b onto the whole of a without first subtracting a inside the bracket gives a + (2/3)b; and treating the ratio as though AP and PB were equal gives the midpoint, (1/2)a + (1/2)b. Convert the ratio to a fraction of AB measured from the point named first in the ratio, subtract before you scale, and then add the result to OA.
- (b) 12 cm — Method: the area of a rectangle is one side multiplied by the other, so when the area and one side are known the other side is found by reversing that multiplication — divide the area by the side that is known. Working: 96 ÷ 8 = 12. Answer: 12 cm. The distractors: 88 cm comes from 96 − 8, subtracting the known side as though the area had been made by adding the two sides together; 768 cm comes from 96 × 8, running the area rule forwards on the two numbers given instead of reversing it; 40 cm comes from reading the 96 as a perimeter — halving it to 48 and taking the 8 cm side away — which reverses the perimeter rule rather than the area rule.
- (d) Wrong - the given angle is not the included angle — Sides AB and BC meet at vertex B, so the included angle needed for SAS is angle B, not angle A — the information given is SSA. SSA does not prove congruence: with AB = 10 cm, BC = 7 cm and angle A = 40° there are two different triangles that fit, one with angle C ≈ 74.6° and one with angle C ≈ 105.4°, so Sam's triangles need not be the same shape and size at all. Sam is not correct just because two sides and an angle are equal, since the angle must be the one INCLUDED between those two sides. The condition is not ASA either, because ASA needs two angles, and only one angle is given here. It is also not true that nothing matches — the stated lengths and angle DO match between the two triangles; the problem is which angle was given, not whether the values agree.
Build your own mix at the worksheet builder.