Printable · GCSE Higher · ages 14-16
Geometry and measures worksheet — GCSE Higher
Fifteen questions across the geometry and measures statements at Higher tier. Choose the non-calculator filter to rehearse Paper 1, which counts for a third of the marks.
Non-calculator
Geometry and measures worksheet — GCSE Higher
MathsUKwww.geekhero.co.uk
- 1.A triangle has vertices A(0, 0), B(10, 0) and C(5, 12). Work out the area of the triangle.
- 2.A water tank holds 2.5 m³. Work out this volume in cm³.
- 3.A pop-up canopy has two sloping supports that meet at the top. Each support makes an angle of 30° with the ground and is 6 m long. Using the exact value of cos 30°, work out the total width of the canopy's base.
- 4.A crane's hook starts at the point (3.4, 9.5) on a construction site plan measured in metres. It moves along the vector to pick up a beam, then along the vector to place it. Work out the single column vector that describes the hook's overall movement from its start position to where it places the beam.
- 5.A plumber charges a £45 call-out fee, plus £28 for each hour worked. She works on a job for 3 hours 30 minutes, and her hours are billed by rounding up to the next whole hour. Work out the total amount she charges.
- 6.A circle has diameter 10 cm. Using π = 3.14, work out the circumference of the circle.
- 7.A, B and C are points on a circle with centre O. B is on the minor arc AC. Angle ABC = 100°. Work out the size of the non-reflex angle AOC.
- 8.A garden designer describes a flower bed as a shape with four straight sides: exactly one pair of sides is parallel, those two parallel sides are different lengths, and the other two sides are equal in length to each other but not parallel to each other. Which shape should the designer draw?
- 9.In triangle ABC the angle at C is 90° and the hypotenuse AB is 12 cm. H is the point on AB for which CH is perpendicular to AB, and AH = 3 cm. Work out the length of AC.
- 10.A triangle has vertices X, Y and Z, with a right angle at Y. Side XY is twice as long as side YZ. Which of the following correctly describes this triangle?
- 11.A rectangular garden gate is 3 m wide and 4 m high. A straight brace runs from one corner of the gate to the opposite corner. Work out the length of the brace.
- 12.A cylinder has a volume of 942 cm³ and a height of 12 cm. Using π = 3.14, work out the radius of the cylinder.
- 13.A shape is translated by the vector , and one vertex of the image is at the point (1, 6). The original shape is instead translated by the vector . Work out the coordinates of the image of that same vertex under this second translation.
- 14.A trapezium-shaped garden bed has parallel sides of 2.5 m and 4.5 m, and a perpendicular width of 3 m. A gardener wants to know the area of the bed before ordering topsoil. Work out the area of the garden bed.
- 15.Shape S is enlarged by a scale factor of −3 about a fixed centre. Which statement correctly describes the image compared to the original shape?
Answer key
- (b) 60 units² — Method: the area of a triangle is half the base times the perpendicular height, so choose a side to act as the base and measure the perpendicular distance from the opposite vertex to it. Working: A(0, 0) and B(10, 0) both lie on the x-axis, so AB is horizontal and AB = 10 − 0 = 10. The perpendicular height is the distance of C from the x-axis, which is its y-coordinate, 12. Area = (10 × 12) ÷ 2 = 120 ÷ 2 = 60. Answer: 60 units². The distractors: 120 units² comes from multiplying base by height and forgetting to halve; 65 units² comes from using the slanting side AC, which is 13 long, as the height in place of the perpendicular distance 12; 30 units² comes from halving the base to 5 before multiplying and then halving the product as well, so the halving is done twice.
- (b) 2 500 000 cm³ — Method: a volume conversion uses the length factor three times, once for each dimension. Working: 1 m = 100 cm, so a cube of side 1 m is a cube of side 100 cm, and 100 × 100 × 100 = 1 000 000, giving 1 m³ = 1 000 000 cm³. Then 2.5 × 1 000 000 = 2 500 000. Answer: 2 500 000 cm³. Using the plain length factor 100 gives 250 cm³. Using 1000, which is the factor that turns cubic metres into litres, gives 2500 cm³. Using 10 000, which is the factor that belongs to square metres and square centimetres, gives 25 000 cm³.
- (b) 6√3 m — The horizontal distance covered by one support is adjacent to the 30° angle, so it equals 6 × cos 30° = 6 × √3/2 = 3√3 m. The total base width is made up of both supports, so it is 2 × 3√3 = 6√3 m. '3√3 m' gives only one support's horizontal distance and forgets to double it for the total width. '6 m' comes from using sin 30° instead of cos 30° for the horizontal distance (6 × sin 30° = 3, doubled to 6). '12 m' comes from doubling the full sloping length of 6 m without using any trigonometry at all.
- (b) $\binom{-0.4}{-7}$ — The overall movement is the sum of the two vectors: (−1.2 + 0.8, −4.5 + (−2.5)) = (−0.4, −7). '$\binom{-2}{-2}$' comes from subtracting the second vector from the first instead of adding them. '$\binom{-0.4}{7}$' gets the top number right but drops the negative sign on the bottom number. '$\binom{2}{-7}$' comes from treating −1.2 + 0.8 as if the signs did not matter, giving +2 instead of −0.4.
- (b) £157 — Method: round the hours worked up to the next whole hour, multiply by the hourly rate, then add the call-out fee. Working: 3 hours 30 minutes rounds up to 4 hours; 28 × 4 = 112; 112 + 45 = 157. Answer: £157. A candidate who uses the unrounded time of 3.5 hours, working out 28 × 3.5 = 98 and adding 45, gets £143. A candidate who forgets the call-out fee, giving only 28 × 4, gets £112. A candidate who rounds down to 3 hours instead of up, working out 28 × 3 = 84 and adding 45, gets £129.
- (b) 31.4 cm — Circumference = π × diameter, so 3.14 × 10 = 31.4 cm. 15.7 cm comes from using the radius, 5 cm, in place of the diameter: 3.14 × 5 = 15.7, which is only half the circumference. 78.5 cm comes from using the area formula π × radius² instead of the circumference formula: 3.14 × 5² = 3.14 × 25 = 78.5. 62.8 cm comes from keeping the 2 from the radius form of the formula, C = 2 × π × radius, but putting the full diameter into it: 2 × 3.14 × 10 = 62.8.
- (b) 160° — B is on the minor arc AC, so the angle at the centre theorem applies to the reflex angle AOC: reflex angle AOC = 2 × 100° = 200°. The non-reflex angle AOC is the rest of the full turn: 360° − 200° = 160°. Reporting the reflex angle itself, without subtracting it from 360°, gives 200°. Subtracting angle ABC from 180° instead, as if this were a cyclic quadrilateral, gives 80°. Halving angle ABC instead of doubling it gives 50°. Double first, then take the angle away from a full turn, and 160° is what's left.
- (a) isosceles trapezium — One pair of parallel sides, plus a separate pair of equal non-parallel sides, is exactly the definition of an isosceles trapezium — the shape the designer should draw. Parallelogram is wrong because a parallelogram needs BOTH pairs of opposite sides parallel, but only one pair is parallel here. Kite is wrong because a kite has two separate pairs of adjacent equal sides and no requirement for any sides to be parallel, a different combination of properties. Rhombus is wrong because a rhombus needs all four sides equal, but the description only makes two of the four sides equal to each other.
- (d) 6 cm — Method: CH cuts the triangle into two smaller right-angled triangles, so Pythagoras' theorem can be written in each of the three right-angled triangles and the results combined. Working: HB = 12 − 3 = 9 cm. In triangle ACH, CH² = AC² − 3² = AC² − 9; in triangle CHB, CH² = CB² − 9² = CB² − 81. Setting those equal gives AC² − 9 = CB² − 81. In triangle ABC, AC² + CB² = 12² = 144, so CB² = 144 − AC². Substituting gives AC² − 9 = 144 − AC² − 81, so 2 × AC² = 72 and AC² = 36, giving AC = 6. Answer: 6 cm. The distractors: 36 cm comes from stopping at AC² = 36 and never taking the square root; 9 cm is HB, the other part of the hypotenuse, written down in place of AC; 4 cm comes from working out 12 ÷ 3, treating AH as a scale factor between the two triangles rather than as a length.
- (b) A right-angled triangle — The right angle at Y makes this a right-angled triangle, so that description is correct. Since XY is twice YZ, those two sides cannot be equal. The third side XZ is opposite the right angle, so it is the hypotenuse and is longer than either XY or YZ, so it cannot equal either of them. No two sides are equal, which rules out 'an isosceles triangle' and 'a right-angled isosceles triangle', both of which wrongly assume two equal sides. 'An equilateral triangle' would need all three sides equal, which contradicts XY being twice YZ, so it is wrong too.
- (b) 5 m — Method: the brace, the width and the height form a right-angled triangle in which the brace faces the right angle, so it is the hypotenuse and Pythagoras' theorem applies, a² + b² = c². Working: c² = 3² + 4² = 9 + 16 = 25, so c = √25 = 5. Answer: 5 m. The distractors: 7 m comes from adding the two sides, 3 + 4, instead of adding their squares; 25 m comes from stopping at c² = 25 and forgetting to take the square root; 12 m comes from multiplying 3 × 4, which gives the area of the gate in square metres and not a length across it.
- (c) 5 cm — Volume of a cylinder = πr²h, so r² = V ÷ (πh) = 942 ÷ (3.14 × 12) = 942 ÷ 37.68 = 25, and r = √25 = 5 cm. A pupil who finds r² = 25 but forgets to take the square root gives 25 cm. A pupil who forgets to divide by π, using r² = 942 ÷ 12 = 78.5, gets r = √78.5 ≈ 8.9 cm. A pupil who forgets to divide by the height, using r² = 942 ÷ 3.14 = 300, gets r = √300 ≈ 17.3 cm. The correct radius is 5 cm.
- (d) (11, −2) — First undo the original translation to find the vertex on the original shape: (1 − (−8), 6 − 3) = (9, 3). Then apply the second vector to that original vertex: (9 + 2, 3 + (−5)) = (11, −2). (3, 1) comes from applying the second vector to the image point (1, 6) instead of to the original vertex — (1 + 2, 6 + (−5)) = (3, 1). (7, 8) comes from subtracting the second vector from the original vertex (9, 3) instead of adding it — (9 − 2, 3 − (−5)) = (7, 8). (11, 3) comes from applying only the x-component of the second vector to the original vertex and leaving the y-coordinate unchanged.
- (b) 10.5 m² — The area of a trapezium is half of the sum of the parallel sides, multiplied by the width. Add the parallel sides: 2.5 + 4.5 = 7. Multiply by the width: 7 × 3 = 21. Half of 21 is 10.5 m². 21 m² forgets to halve, using the full (2.5+4.5)×3. 3.5 m² averages the two parallel sides, (2.5+4.5)÷2 = 3.5, but forgets to multiply by the width. 6.75 m² treats the bed as a triangle, using only the longer parallel side: half of 4.5 × 3.
- (a) 3 times the size, opposite side, rotated 180° — Method: for any enlargement, the MAGNITUDE of the scale factor gives the size ratio between image and object, while the SIGN decides which side of the centre the image falls on; a negative scale factor puts the image on the opposite side, which is equivalent to a 180° rotation about the centre. Working: the scale factor is −3, so the size ratio is the magnitude, which is 3, and the negative sign puts the image on the opposite side of the centre, rotated 180° relative to the original. Answer: 3 times the size, opposite side, rotated 180°. The magnitude of the scale factor controls the SIZE only: do not let the sign leak into it and turn 3 into 1/3. The sign controls the SIDE and orientation, which a positive-only view of enlargement, just 'further away' with the same orientation, misses entirely.
Build your own mix at the worksheet builder.