Printable · GCSE Higher · ages 14-16
Geometry and measures worksheet — GCSE Higher
Fifteen questions across the geometry and measures statements at Higher tier. Choose the non-calculator filter to rehearse Paper 1, which counts for a third of the marks.
Geometry and measures worksheet — GCSE Higher
MathsUKwww.geekhero.co.uk
- 1.Work out the gradient of the line segment joining A(2, 3) and B(6, 11).
- 2.A roof truss is shaped like an isosceles triangle resting on a horizontal ceiling joist. The truss's sloping edges are equal in length, and the angle at its apex is 40°. The ceiling joist continues in a straight line beyond the foot of the truss. Work out the angle between the truss's sloping edge and the extended joist, on the outside of the truss.
- 3.A solid has 6 faces and 8 vertices. Using the formula F + V − E = 2, work out how many edges it has.
- 4.In one circle, chord PQ is 6 cm long, chord RS is 10 cm long, chord TU is 14 cm long and chord VW is 15 cm long. Write down which of these chords lies closest to the centre of the circle.
- 5.In a right-angled triangle one of the other two angles is 45°, and the side opposite that 45° angle is 7 cm. Work out the length of the hypotenuse. Give your answer to 1 decimal place.
- 6.A scale model of a bridge is built so that 2 cm on the model represents 5 m of the real bridge. The real bridge is 45 m long. Work out the length of the model bridge, in centimetres.
- 7.A hexagonal prism lies on a table. A flat cut is made straight across it, at right angles to its length (so the cut is parallel to the two identical end faces). What shape is the cross-section?
- 8.In triangle ABC, AB = 8.6 cm, AC = 11.4 cm and angle BAC = 47°. Work out the area of triangle ABC. Give your answer to 1 decimal place.
- 9.A line joins the points A(0, 0, 0) and B(9, 12, 8) in a three-dimensional coordinate system in which the z-axis is vertical. Work out the angle this line makes with the horizontal (the xy-plane). Give your answer correct to 1 decimal place.
- 10.A cuboid has three different edge lengths: a length, a width and a height, all different from each other. How many rectangles make up its net in total?
- 11.Two similar triangles have lengths in the ratio 3 : 4. The perimeter of the smaller triangle is 24 cm. Work out the perimeter of the larger triangle.
- 12.In quadrilateral WXYZ, which of the following correctly names the angle at vertex Y using standard notation?
- 13.Point P is translated by the vector (5, −2), and the image is then rotated 90° clockwise about the origin to give the point (3, 9). Work out the coordinates of P.
- 14.A sprinkler waters a sector-shaped patch of a garden with radius 8 m and angle 90°. Work out the perimeter of the watered sector, to 1 decimal place. (Use π = 3.14.)
- 15.Work out the exact value of tan 30° + tan 30°.
Answer key
- (a) 2 — Gradient = (change in y) ÷ (change in x) = (11 − 3) ÷ (6 − 2) = 8 ÷ 4 = 2. "0.5" comes from dividing the change in x by the change in y the wrong way round: 4 ÷ 8. "8" is only the change in y, forgetting to divide by the change in x at all. "−2" comes from a sign error, as if the y-coordinate had decreased rather than increased.
- (a) 110° — The truss is isosceles, so its two base angles are equal; since the three angles of the triangle add up to 180° and the apex is 40°, each base angle is (180 − 40) ÷ 2 = 70°. The angle between the sloping edge and the joist, extended beyond the base of the truss, sits on a straight line with that 70° base angle, and angles on a straight line add up to 180°, so the required angle is 180 − 70 = 110°. "70°" comes from stopping after finding the base angle and giving it directly, without also using the straight-line fact to find the angle on the OUTSIDE of the truss. "140°" comes from doubling the base angle instead of using the straight-line fact. "20°" comes from taking half of the apex angle (40° ÷ 2), mistaking it for the required angle instead of properly using the triangle's angle sum.
- (d) 12 — Method: rearrange F + V − E = 2 so that E is on its own: E = F + V − 2. Working: E = 6 + 8 − 2 = 12. A student who answers 14 has added F and V but forgotten to subtract 2 at all. A student who answers 16 has added 2 instead of subtracting it. A student who answers 10 has subtracted 2 twice by mistake. Answer: 12 edges.
- (c) VW — Method: within one circle a chord's distance from the centre is fixed by its length, because a chord passing nearer the centre cuts further across the circle; so the chord that lies closest to the centre is simply the longest one listed. Working: the four lengths are 6 cm, 10 cm, 14 cm and 15 cm. Placing them in order, the greatest is 15 cm, and that length belongs to VW, so VW lies closest to the centre. Answer: VW. The distractors: PQ comes from reversing the rule and taking the shortest chord to be the one tucked nearest the centre; TU comes from knowing that the very longest chord is a diameter, deciding that such a chord passes through the centre rather than lying close to it, ruling the 15 cm chord out on that ground and taking the next longest; RS comes from reading 'closest to the centre' as 'nearest the middle of the list of lengths' and picking a middling value.
- (c) 9.9 cm — Method: the 7 cm side is opposite the 45° angle and the hypotenuse is wanted, so use sin θ = opposite ÷ hypotenuse and rearrange it for the hypotenuse. Working: sin 45° = 7 ÷ h, so h = 7 ÷ sin 45° = 9.899…, which is 9.9 to 1 decimal place. Answer: 9.9 cm. The distractors: 5.0 cm comes from multiplying by sin 45° instead of dividing by it; 14.0 cm comes from doubling the 7 cm side, which is the rule for a side opposite 30° and not one opposite 45°; 7.0 cm comes from reading the two equal sides of a 45° right-angled triangle as including the hypotenuse, when the equal pair is the two shorter sides.
- (c) 18 — Method: divide the real length by 5 to find how many 'units' of 5 m it contains, then multiply by 2 cm for each unit. Working: 45 ÷ 5 = 9, so the real bridge is 9 lots of 5 m; each lot is represented by 2 cm on the model, so the model length is 9 × 2 = 18 cm. Options: 9 comes from stopping after the division, without multiplying by the 2 cm per unit; 90 comes from multiplying the real length by 2 directly, without dividing by 5 first; 4.5 comes from dividing by 5 and then dividing by 2 again, instead of multiplying by 2. Answer: 18.
- (b) Hexagon — Cutting straight across a prism, at right angles to its length, always gives a cross-section that is the same shape as its end faces. The end faces of a hexagonal prism are hexagons (6-sided), so the cross-section is a hexagon. Choosing Pentagon comes from miscounting the sides of the hexagonal end as five instead of six. Choosing Rectangle comes from cutting along the LENGTH of the prism instead of across it, which gives a rectangular face, not the cross-section asked for. Choosing Triangle comes from confusing a hexagonal prism with a triangular prism.
- (a) 35.9 cm² — Method: the area of any triangle is 1/2 × a × b × sin C, where a and b are two sides and C is the angle between them. Working: the 47° angle lies between AB = 8.6 cm and AC = 11.4 cm, so the area is 1/2 × 8.6 × 11.4 × sin 47° = 49.02 × 0.73135 = 35.851. Answer: the area is 35.9 cm² to 1 decimal place. The distractors: 71.7 cm² comes from leaving out the factor 1/2 and working out 8.6 × 11.4 × sin 47°; 33.4 cm² comes from pressing cos instead of sin, 49.02 × cos 47°, which is the same as using the complement 43° in place of 47°; 52.6 cm² comes from pressing tan instead of sin, 49.02 × tan 47°.
- (a) 28.1° — The angle a line makes with the horizontal plane lies in the right-angled triangle formed by the vertical rise, the horizontal distance travelled, and the line itself. The horizontal distance from A to B is √(9² + 12²) = √(81 + 144) = √225 = 15, using only the x- and y-coordinates. The vertical rise is the z-coordinate, 8, so tan(angle) = 8 ÷ 15, giving angle = 28.1° (1 d.p.). Inverting the ratio, tan(angle) = 15 ÷ 8, gives 61.9° instead — the complement of the angle, not the angle with the horizontal. Using only the x-coordinate as if it were the whole horizontal distance, tan(angle) = 8 ÷ 9, gives 41.6°. Using the y-coordinate alone in the same way, tan(angle) = 8 ÷ 12, gives 33.7°.
- (a) 6 — A cuboid has six faces in total: a top, a bottom, a front, a back, and two ends — each one is a rectangle in the net, giving six rectangles altogether. Choosing 3 counts only the three PAIRS of congruent rectangles (top/bottom, front/back, two ends) rather than all six individual faces. Choosing 5 forgets one face, as if the net were missing its lid. Choosing 12 is the number of edges of a cuboid, not the number of rectangles in its net.
- (c) 32 cm — Method: a perimeter is lengths added together, so it scales by the length scale factor itself, which is 4 ÷ 3 going from the smaller triangle to the larger one — not by its square. Working: 24 ÷ 3 = 8, and 8 × 4 = 32. Answer: 32 cm. The distractors: 18 cm comes from multiplying by 3 ÷ 4, scaling from the larger triangle down to the smaller one; 25 cm comes from adding the difference between the parts of the ratio, 4 − 3 = 1, to the perimeter; 8 cm comes from dividing by 3 and stopping there, before multiplying by 4.
- (c) ∠XYZ — The angle at a named vertex is written with that vertex's letter in the middle, flanked by its two neighbouring vertices. The angle at Y sits between X and Z, its neighbours in quadrilateral WXYZ, so it is written ∠XYZ. ∠WXY names the angle at X, since X is the middle letter, not Y. ∠YZW names the angle at Z, since Z is the middle letter. ∠ZWX names the angle at W, since W is the middle letter.
- (d) (−14, 5) — To undo a composition, reverse the order and invert each transformation: undo the rotation first, then undo the translation. The inverse of 'rotate 90° clockwise about the origin' is 'rotate 90° anticlockwise about the origin', which maps (x, y) to (−y, x); applied to (3, 9) this gives (−9, 3). Then undo the translation by subtracting the vector (5, −2), i.e. adding (−5, 2): (−9 − 5, 3 + 2) = (−14, 5). Undoing the two inverse steps in the same order as the original composition, rather than reversing it, gives (−11, −2). Rotating 90° clockwise again instead of inverting the rotation's direction gives (4, −1). Adding the translation vector again instead of subtracting it, after correctly inverting the rotation, gives (−4, 1).
- (a) 28.6 m — The perimeter of a sector is the two straight radii plus the curved arc. This sector's 90° angle is one quarter of a full turn, so its arc length is one quarter of the full circle's circumference. The full circumference is 2 × 3.14 × 8 = 50.24 m, and one quarter of that is 50.24 ÷ 4 = 12.56 m. Add the two 8 m radii: 12.56 + 8 + 8 = 28.56 m, which rounds to 28.6 m. Choosing 12.6 m gives the arc length alone (rounded), forgetting the two straight edges of the sector. Choosing 20.6 m adds only one radius to the arc length instead of two, missing one of the two straight sides. Choosing 41.1 m comes from using the diameter, 16 m, as if it were the radius when working out the arc length (2 × 3.14 × 16 = 100.48, one quarter of which is 25.12), then adding the two correct 8 m radii (25.12 + 8 + 8 = 41.12).
- (a) 2√3/3 — tan 30° = √3/3, so tan 30° + tan 30° = 2 × √3/3 = 2√3/3. √3 comes from wrongly treating tan 30° + tan 30° as tan(30° + 30°) = tan 60° = √3 — adding angles is not the same as adding ratios. √3/3 comes from forgetting to double the value and just writing down tan 30° on its own. 2√3 comes from doubling the numerator of √3/3 but forgetting to keep the denominator of 3.
Build your own mix at the worksheet builder.