Printable · GCSE Higher · ages 14-16
Geometry and measures worksheet — GCSE Higher
Fifteen questions across the geometry and measures statements at Higher tier. Choose the non-calculator filter to rehearse Paper 1, which counts for a third of the marks.
Geometry and measures worksheet — GCSE Higher
MathsUKwww.geekhero.co.uk
- 1.Point A and point B are 5 cm apart. How many points are exactly 4 cm from A and exactly 3 cm from B?
- 2.A triangle has vertices X, Y and Z, with a right angle at Y. Side XY is twice as long as side YZ. Which of the following correctly describes this triangle?
- 3.A carpenter measures two triangular braces. Brace 1 has a 55° angle, a 65° angle, and, opposite the 55° angle, a side of 8 cm. Brace 2 has matching 55° and 65° angles and, opposite its 55° angle, a side of 8 cm. The carpenter says that because the equal 8 cm side is not between the two equal angles in either brace, he cannot be sure the two braces are the same size. Is the carpenter correct?
- 4.The angle between north and a cycle path is 40°, but it is measured anticlockwise from north. What is the three-figure bearing of the cycle path?
- 5.A window is made from a rectangle with a semicircle on top. The rectangle is 40 cm wide and 60 cm tall. The semicircle has the same width as the rectangle. Work out the total area of the window. Use π = 3.14. Give your answer to the nearest whole number.
- 6.Work out the exact value of tan 30° + tan 30°.
- 7.In triangle ABC, AB = 13 cm, AC = 9 cm and angle ABC = 35°. Given that angle ACB is obtuse, work out its size. Give your answer to 1 decimal place.
- 8.A construction for the perpendicular bisector of AB begins by opening a pair of compasses to more than half the length of AB, then drawing an arc centred at A. What is the next step?
- 9.A solid pyramid has a square base of side 10 cm and four identical triangular faces. Its apex is directly above the centre of the base, at a vertical height of 12 cm, and the slant height of each triangular face — the distance from the apex to the midpoint of a base edge — is 13 cm. Work out the total surface area of the pyramid.
- 10.A shop sells rice in packs of 250 g. Aisha buys 4 packs. Work out the total mass of rice she buys, in kilograms.
- 11.Two similar triangular flower beds have lengths in the ratio 3 : 7. The area of the smaller bed is 45 m². Work out the area of the larger bed.
- 12.Two triangles are proved congruent using the ASA condition. What can be concluded about the two remaining pairs of corresponding sides that were not part of the original ASA facts?
- 13.A designer creates a repeating tile pattern. Each tile is translated from the one before it by the column vector with top number 4.5 and bottom number −2.5 (in centimetres). The first tile has its bottom-left corner at (1.5, 3). Work out the coordinates of the bottom-left corner of the third tile.
- 14.A scale drawing of a bridge uses a scale of 1 : 25. A support beam on the drawing measures 4.4 cm. What is the real length of the beam, in metres?
- 15.Shape T has a vertex at (5, 3). T is enlarged by scale factor −1, centre (2, 1). Work out the coordinates of the image of the vertex (5, 3).
Answer key
- (c) 2 — A point 4 cm from A lies on a circle of radius 4 cm centred at A; a point 3 cm from B lies on a circle of radius 3 cm centred at B. Since AB = 5 cm, and 4 + 3 = 7 is greater than 5 while 4 − 3 = 1 is less than 5, the two circles genuinely cross each other, at two separate points, one on each side of line AB. "1" comes from wrongly assuming the circles only touch rather than cross, which would need 4 + 3 to equal exactly 5. "0" comes from wrongly assuming the circles miss each other completely. "4" comes from counting where each circle crosses the line AB itself (two points each) instead of counting where the two circles cross each other.
- (b) A right-angled triangle — The right angle at Y makes this a right-angled triangle, so that description is correct. Since XY is twice YZ, those two sides cannot be equal. The third side XZ is opposite the right angle, so it is the hypotenuse and is longer than either XY or YZ, so it cannot equal either of them. No two sides are equal, which rules out 'an isosceles triangle' and 'a right-angled isosceles triangle', both of which wrongly assume two equal sides. 'An equilateral triangle' would need all three sides equal, which contradicts XY being twice YZ, so it is wrong too.
- (d) No — third angle is also fixed — Since both braces have angles of 55° and 65°, their third angles must both be 60°, because angles in a triangle sum to 180°. All three angles now match, so the braces have the same shape. Both 8 cm sides lie in the same position relative to those angles — opposite the 55° angle in each brace — so one matching pair of corresponding sides fixes the size as well, exactly as ASA or AAS would. The braces are therefore guaranteed to be congruent and the carpenter is incorrect: 'No — third angle is also fixed' is correct. 'Yes — side must be included' is wrong because the side does not have to lie physically between the two named angles; once the third angle is fixed, a corresponding equal side anywhere is enough. 'No — any two angles enough alone' is wrong because two equal angles with no side length at all would only show the triangles are similar, not congruent. 'Yes — third angle may differ' is wrong because the third angle is fixed at 60° by the angle sum and cannot vary.
- (b) 320° — A bearing is always measured clockwise from north. An angle measured anticlockwise must be converted by subtracting it from 360°: 360 − 40 = 320°, so the bearing is 320°. Choosing 040° treats the anticlockwise angle as if it were already a clockwise bearing, without converting it. Choosing 220° adds 180° to the angle, mixing this up with a back-bearing calculation (40 + 180 = 220). Choosing 400° adds the angle to 360° instead of subtracting it (40 + 360 = 400), giving a bearing greater than a full turn.
- (c) 3028 cm² — Split the window into a rectangle and a semicircle. Rectangle area = 40 × 60 = 2400 cm². The semicircle has radius 40 ÷ 2 = 20 cm, so its area = 0.5 × 3.14 × 20² = 628 cm². Total area = 2400 + 628 = 3028 cm². A student who uses a full circle instead of a semicircle on top of the rectangle gets 3.14 × 20² = 1256 cm² for the circle, plus 2400 cm² for the rectangle, totalling 3656 cm². A student who uses the rectangle's full width (40 cm) as the radius instead of halving it gets 0.5 × 3.14 × 40² = 2512 cm² for the semicircle, plus 2400 cm² for the rectangle, totalling 4912 cm².
- (a) 2√3/3 — tan 30° = √3/3, so tan 30° + tan 30° = 2 × √3/3 = 2√3/3. √3 comes from wrongly treating tan 30° + tan 30° as tan(30° + 30°) = tan 60° = √3 — adding angles is not the same as adding ratios. √3/3 comes from forgetting to double the value and just writing down tan 30° on its own. 2√3 comes from doubling the numerator of √3/3 but forgetting to keep the denominator of 3.
- (b) 124.1° — Method: use the sine rule AB/sin(ACB) = AC/sin(ABC), since AB is opposite angle ACB and AC is opposite angle ABC. Working: sin(ACB) = AB × sin(ABC) / AC = 13 × sin 35° / 9 = 0.8285, which gives angle ACB = 55.9° or its supplement 180 − 55.9 = 124.1°; both of these give a valid triangle, and since angle ACB is obtuse the answer is 124.1°. Reporting the acute solution instead, without checking the word 'obtuse' in the question, gives 55.9°; putting the sides the wrong way round in the ratio, sin(ACB) = 9 × sin 35° / 13, gives 23.4°; and subtracting the acute solution and the given 35° from 180° as if angle ACB were the remaining triangle angle gives 89.1°. A given SSA fact always has two possible angle solutions unless the stem states which one is meant.
- (b) an arc of the same radius, centred at B — The perpendicular bisector construction needs two arcs of equal radius, one centred at each end of the segment — after the arc from A, the next step is an arc of exactly the same radius from B, so the two arcs cross at two points; the line through those two crossing points is the perpendicular bisector. "an arc of the same radius, centred at the midpoint of AB" is not possible yet, since the midpoint is only found once both arcs are drawn — it is the RESULT of the construction, not a step in it. "a smaller arc, centred at A again" gives two different-sized arcs from the same point, which never cross to give the bisector. "a straight line joining the ends of the first arc" only connects points on one arc, and locates nothing.
- (b) 360 cm² — Method: the total surface area is the square base plus the four triangular faces, and the height used for a triangular face is the slant height of 13 cm, not the vertical height of 12 cm. Working: the base is 10 × 10 = 100 cm²; one triangular face is (10 × 13) ÷ 2 = 65 cm², so four faces give 4 × 65 = 260 cm²; the total is 100 + 260 = 360. Answer: 360 cm². The distractors: 260 cm² comes from adding the four triangular faces and leaving out the base; 340 cm² comes from using the vertical height of 12 cm as the height of each triangle, 100 + 4 × 60; 620 cm² comes from working out each face as 10 × 13 without halving, 100 + 4 × 130.
- (d) 1 kg — First find the total mass in grams: 4 × 250 = 1000 g. Then convert to kilograms by dividing by 1000: 1000 ÷ 1000 = 1 kg. Finding the correct total in grams but forgetting to divide by 1000 gives 1000 kg. Adding the number of packs to the pack mass instead of multiplying, 4 + 250 = 254 g, gives 0.254 kg. Dividing the pack mass by the number of packs instead of multiplying, 250 ÷ 4 = 62.5 g, gives 0.0625 kg.
- (a) 245 m² — Method: for similar figures the ratio of the areas is the square of the ratio of the lengths, so multiply the smaller area by the square of the length scale factor. Working: the length scale factor is 7 ÷ 3, so the area scale factor is 49 ÷ 9, and the larger area is 45 × 49 ÷ 9 = 5 × 49 = 245. Answer: 245 m². The distractors: 105 m² comes from multiplying by the length scale factor 7 ÷ 3 instead of by its square, the commonest slip on this topic; 315 m² comes from multiplying by 7 and forgetting to divide by 3; 405 m² comes from multiplying by 3² = 9, squaring the wrong part of the ratio.
- (c) They must also be equal — Once two triangles are proved congruent by any condition, including ASA, they are identical in every respect: every pair of corresponding sides and every pair of corresponding angles must be equal, not just the ones originally used to prove the congruence. So the two remaining pairs of corresponding sides must also be equal, making 'they must also be equal' correct. 'They might be equal or not' and 'not enough information to say' both wrongly suggest that congruence only guarantees the specific facts used to prove it, when congruence actually guarantees the triangles are identical overall. 'They must be different' is backwards: the triangles being identical is the entire point of proving congruence, not a reason for a side to differ.
- (c) (10.5, −2) — Method: the vector from the first tile to the third tile is the pattern's vector doubled, since two translations happen between them. Working: doubling (4.5, −2.5) gives (9, −5); adding this to the starting corner (1.5, 3) gives x-coordinate 1.5 + 9 = 10.5 and y-coordinate 3 − 5 = −2. Answer: (10.5, −2). A candidate who only applies the vector once, translating to the second tile instead of the third, gets (6, 0.5). A candidate who adds 2.5 instead of subtracting it in the y-coordinate gets (10.5, 8). A candidate who doubles the x-part of the vector correctly but forgets to change the y-coordinate at all gets (10.5, 3).
- (d) 1.1 — Method: multiply the drawing length by the scale factor to get the real length, then convert to the units asked for. Working: 4.4 cm × 25 = 110 cm = 1.1 m. A student who answers 4.4 has forgotten to use the scale at all. A student who answers 110 has correctly worked out the real length in centimetres but forgotten to convert it to metres. A student who answers 11 has used a scale factor of 2.5 instead of 25 by misreading the scale. Answer: 1.1 m.
- (b) (−1, −1) — An enlargement by scale factor −1, centre (2, 1), sends a point P to the point on the opposite side of the centre, the same distance away: the image is 2 × centre − P. For the vertex (5, 3), this gives (2 × 2 − 5, 2 × 1 − 3) = (4 − 5, 2 − 3) = (−1, −1). Treating the centre as though it were the origin, and simply negating the point's coordinates, gives (−5, −3) — this ignores that the true centre is (2, 1), not (0, 0). Using scale factor +1 instead of −1 leaves the point exactly where it started, at (5, 3). Adding the point's displacement from the centre instead of subtracting it gives (2 × 2 + 5, 2 × 1 + 3) = (9, 5). Double the centre and subtract the point, and the image is (−1, −1).
Build your own mix at the worksheet builder.