Printable · GCSE Higher · ages 14-16
Geometry and measures worksheet — GCSE Higher
Fifteen questions across the geometry and measures statements at Higher tier. Choose the non-calculator filter to rehearse Paper 1, which counts for a third of the marks.
Geometry and measures worksheet — GCSE Higher
MathsUKwww.geekhero.co.uk
- 1.A ramp rises at 30° to the horizontal. Its sloping surface is 4.8 m long. Safety rules say the vertical rise of a ramp must be no more than 2.5 m. Work out how far below that limit the rise of this ramp is.
- 2.A running track has a straight section and a semicircular bend. The bend is a semicircle with radius 32 m. Work out the length of the curved part of the bend, to 1 decimal place. (Use π = 3.14.)
- 3.A drone starts at the point (3.5, −2) on a grid measured in metres. It flies by the vector to check a first sensor. The drone then needs to fly in a straight line to reach the point (−1.7, 9) to check a second sensor. Work out the column vector of this second flight.
- 4.In one circle, chord PQ is 6 cm long, chord RS is 10 cm long, chord TU is 14 cm long and chord VW is 15 cm long. Write down which of these chords lies closest to the centre of the circle.
- 5.Triangles ABE and CDE share the vertex E, where lines AC and BD cross at E. AE equals CE, and BE equals DE. Angle AEB and angle CED are formed as vertically opposite angles where the lines cross. Which condition proves that triangle ABE is congruent to triangle CDE?
- 6.A shape is translated by the vector (5, −3), and the image is then translated by the vector (−5, 3). Which single transformation has the same overall effect as this combination, for every point?
- 7.A chord divides a circle into two segments of different sizes. Write down the name given to the smaller of the two segments.
- 8.Which of these statements about the area formula Area = 1/2ab sin C is correct?
- 9.Shape S is enlarged by a scale factor of −3 about a fixed centre. Which statement correctly describes the image compared to the original shape?
- 10.A roof truss has two horizontal parallel rafters, one above the other. A straight strut crosses both rafters. Where the strut crosses the lower rafter, the angle above the rafter and to the left of the strut is 65°. Work out the size of the angle above the upper rafter and to the right of the strut, where the strut crosses it.
- 11.A rectangular garden gate is 3 m wide and 4 m high. A straight brace runs from one corner of the gate to the opposite corner. Work out the length of the brace.
- 12.Two vertical masts stand on level ground, 40 m apart. One mast is 30 m tall and the other is 50 m tall. Work out the straight-line distance between the tops of the two masts. Give your answer to 1 decimal place.
- 13.A designer plots a logo point at (3, 4) on a grid. She reflects it in the line y = 1 and then rotates the image 90° clockwise about the point (1, 1) to create a repeating tile pattern. Work out the coordinates of the point after both transformations.
- 14.Two coastguard stations A and B are 18 km apart, with B due east of A. A boat at C is on a bearing of 062° from A and on a bearing of 315° from B. Work out the distance of the boat from station B. Give your answer to 1 decimal place.
- 15.A rectangular name card has a perimeter of 30 cm. The card is 9 cm long. Work out the width of the card.
Answer key
- (a) 0.1 m — Method: the sloping surface is the hypotenuse and the vertical rise is the side opposite the 30° angle, so rise = 4.8 × sin 30°; then compare that rise with the limit. Working: the exact value of sin 30° is one half, so the rise = 4.8 × 1/2 = 2.4 m. The limit is 2.5 m, and 2.5 − 2.4 = 0.1. Answer: the ramp is 0.1 m below the limit. Working out the rise and stopping there gives 2.4 m, which answers a question that was not asked. Dividing by sin 30° instead of multiplying gives 4.8 ÷ 0.5 = 9.6 and then 9.6 − 2.5 = 7.1 m. Treating sine as proportional to the angle, so that sin 30° is a third of sin 90°, gives 4.8 ÷ 3 = 1.6 and then 2.5 − 1.6 = 0.9 m.
- (c) 100.5 m — The curved part of a semicircular bend is half of a full circle's circumference. The full circumference would be 2 × 3.14 × 32 = 200.96 m, and half of that is 200.96 ÷ 2 = 100.48 m, which rounds to 100.5 m. Choosing 201.0 m uses the FULL circumference, forgetting to halve it for a semicircle. Choosing 50.2 m halves the radius as well as taking a semicircle, using 3.14 × 16 = 50.24 m instead of the correct radius of 32 m. Choosing 64.0 m uses the diameter, 2 × 32 = 64, as if it were the curved length, ignoring π and the semicircle shape entirely.
- (a) $\binom{1}{6.5}$ — After the first flight, the drone is at (3.5 − 6.2, −2 + 4.5) = (−2.7, 2.5). The second vector takes it from (−2.7, 2.5) to (−1.7, 9): subtract the coordinates, (−1.7 − (−2.7), 9 − 2.5) = (1, 6.5). The distractor $\binom{−4.4}{6.5}$ comes from treating the drone's position after the first flight as (2.7, 2.5) instead of (−2.7, 2.5), giving −1.7 − 2.7 = −4.4 for the top number. The distractor $\binom{−5.2}{11}$ comes from finding the vector straight from the start point (3.5, −2) to (−1.7, 9), ignoring the first flight altogether. The distractor $\binom{−1}{−6.5}$ comes from subtracting the wrong way round, (−2.7 − (−1.7), 2.5 − 9), which reverses both signs of the correct vector.
- (c) VW — Method: within one circle a chord's distance from the centre is fixed by its length, because a chord passing nearer the centre cuts further across the circle; so the chord that lies closest to the centre is simply the longest one listed. Working: the four lengths are 6 cm, 10 cm, 14 cm and 15 cm. Placing them in order, the greatest is 15 cm, and that length belongs to VW, so VW lies closest to the centre. Answer: VW. The distractors: PQ comes from reversing the rule and taking the shortest chord to be the one tucked nearest the centre; TU comes from knowing that the very longest chord is a diameter, deciding that such a chord passes through the centre rather than lying close to it, ruling the 15 cm chord out on that ground and taking the next longest; RS comes from reading 'closest to the centre' as 'nearest the middle of the list of lengths' and picking a middling value.
- (d) SAS, vertically opposite angle included — AE equals CE and BE equals DE give two pairs of equal sides, and angle AEB equals angle CED because they are vertically opposite angles formed where AC and BD cross; vertically opposite angles are always equal without needing to be measured. This included angle sits between the two known sides in each triangle, giving SAS, so 'SAS, vertically opposite angle included' is correct. 'ASA, vertically opposite angle at E' is wrong because ASA needs two pairs of equal angles with the side between them, but only one angle is known in each triangle here, and the two other known facts are sides, not angles. 'SSS, three equal side pairs' is wrong because only two pairs of sides are given; there is no third pair of equal sides. 'Cannot prove — no angle measured' is wrong because vertically opposite angles are always equal automatically when two straight lines cross, so no separate measurement is needed.
- (d) No transformation — every point stays exactly where it was — The two vectors (5, −3) and (−5, 3) are opposites, so adding them gives (0, 0): every point ends up exactly where it started, and there is no transformation at all. Misreading the second vector's signs and effectively adding (5, −3) to itself instead of to its opposite gives a translation by the vector (10, −6). Assuming two translations must combine into a reflection gives a reflection in the x-axis — but a reflection reverses orientation, and translations never do. Assuming that two opposite vectors must mean a half turn gives a rotation of 180° about the origin — but a 180° rotation moves every point except its own centre, whereas this pair of translations leaves every single point exactly where it was. Two translations by opposite vectors always cancel exactly, leaving every point unmoved.
- (b) Minor segment — Method: compare the sizes of the two regions cut off by the chord, and recall the term used for the smaller one. Working: the chord creates two segments; the smaller region is called the minor segment and the larger one the major segment. A student who answers major segment has picked the larger region by mistake instead of the smaller one. A student who answers minor arc has named the curved boundary rather than the two-dimensional region it encloses. A student who answers semicircle has wrongly assumed the chord must pass through the centre. Answer: minor segment.
- (c) AB, AC and angle BAC: Area = 1/2 × AB × AC × sin(BAC) — Method: Area = 1/2ab sin C only works when the angle used is the one included between the two sides being multiplied. Working: AB and AC meet at A, and angle BAC is the angle at A between them, so the statement pairing AB, AC and angle BAC is the correct one. The statement that three sides with no angle can still go into 1/2 AB × AC × sin(BAC) is wrong: with no angle known, sin(BAC) cannot be evaluated, so a different method must find an angle first. The statement pairing AB and BC with sin(BAC) is wrong: AB and BC meet at B, so the angle between them is angle ABC, not angle BAC — it names the wrong angle for the sides it uses. The statement pairing AB and AC with sin(ABC) is wrong for the same reason: AB and AC meet at A, so their included angle is angle BAC, and angle ABC is not between them at all.
- (a) 3 times the size, opposite side, rotated 180° — Method: for any enlargement, the MAGNITUDE of the scale factor gives the size ratio between image and object, while the SIGN decides which side of the centre the image falls on; a negative scale factor puts the image on the opposite side, which is equivalent to a 180° rotation about the centre. Working: the scale factor is −3, so the size ratio is the magnitude, which is 3, and the negative sign puts the image on the opposite side of the centre, rotated 180° relative to the original. Answer: 3 times the size, opposite side, rotated 180°. The magnitude of the scale factor controls the SIZE only: do not let the sign leak into it and turn 3 into 1/3. The sign controls the SIDE and orientation, which a positive-only view of enlargement, just 'further away' with the same orientation, misses entirely.
- (c) 115 — Method: use corresponding angles to carry the 65° angle from the lower rafter up to the upper rafter, then use angles on a straight line to move to the other side of the strut. Working: the angle above the upper rafter and to the left of the strut corresponds to the given angle, so it is 65°; the angle above the upper rafter and to the right of the strut lies on a straight line with it, so it is 180 − 65 = 115. Answer: 115°. A candidate who assumes the angle stays 65° without allowing for the move from the left of the strut to the right of it gives 65. A candidate who uses 90° instead of 180°, working out 90 − 65, gets 25. A candidate who adds instead of subtracting, working out 180 + 65, gets 245.
- (b) 5 m — Method: the brace, the width and the height form a right-angled triangle in which the brace faces the right angle, so it is the hypotenuse and Pythagoras' theorem applies, a² + b² = c². Working: c² = 3² + 4² = 9 + 16 = 25, so c = √25 = 5. Answer: 5 m. The distractors: 7 m comes from adding the two sides, 3 + 4, instead of adding their squares; 25 m comes from stopping at c² = 25 and forgetting to take the square root; 12 m comes from multiplying 3 × 4, which gives the area of the gate in square metres and not a length across it.
- (a) 44.7 m — Method: the line joining the two tops is the hypotenuse of a right-angled triangle whose horizontal side is the gap between the masts and whose vertical side is the difference in their heights, so Pythagoras' theorem applies. Working: the difference in heights is 50 − 30 = 20 m, so d² = 40² + 20² = 1600 + 400 = 2000 and d = √2000 = 44.721…, which is 44.7 m to 1 decimal place. Answer: 44.7 m. The distractors: 34.6 m comes from subtracting the squares, √(40² − 20²), instead of adding them; 60.0 m comes from adding the two sides of the triangle, 40 + 20, rather than using Pythagoras' theorem; 50.0 m is the height of the taller mast, copied from the question in place of the distance asked for.
- (b) (−2, −1) — Method: apply the reflection to the point first, then rotate the image about the given centre, in the order the question states them. Working: reflecting (3, 4) in the line y = 1 keeps x = 3 and puts the image as far below the line as the point is above it: 4 is 3 units above y = 1, so the image is 3 units below, at 1 − 3 = −2 (the same as 2 × 1 − 4 = −2). The reflected point is (3, −2). Rotating (3, −2) by 90° clockwise about (1, 1): subtracting the centre gives 3 − 1 = 2 and −2 − 1 = −3, the clockwise rule swaps and negates these to give −3 and −2, and adding the centre back gives 1 + (−3) = −2 and 1 + (−2) = −1. The final image is (−2, −1). Answer: (−2, −1). Reflect before you rotate, exactly as the design process is described, and rotate about the CENTRE (1, 1) given in the question rather than the origin: either mistake, or reversing the two steps, sends the tile to a different point.
- (d) 8.8 km — Method: turn each bearing into an angle of triangle ABC, find the third angle from the angle sum, then use the sine rule. Working: B is due east of A, so AB itself lies on a bearing of 090°, and the angle at A between AB and AC is 090° − 062° = 28°. From B, station A lies due west on a bearing of 270°, and C lies on 315°, so the angle at B is 315° − 270° = 45°. The third angle is 180° − 28° − 45° = 107°. The side BC faces the 28° angle and AB = 18 km faces the 107° angle, so BC = 18 × sin 28° ÷ sin 107° = 8.4505 ÷ 0.95630 = 8.8366. Answer: the boat is 8.8 km from B, to 1 decimal place. The distractors: 13.3 km comes from pairing BC with the 45° angle at B instead of the 28° angle it faces, which gives the distance AC; 12.0 km comes from never working out the third angle and dividing by sin 45° instead of sin 107°; 16.6 km comes from using the bearing 062° itself as the angle at A, instead of the 28° between AC and AB.
- (a) 6 cm — Method: a rectangle is made of two lengths and two widths, so the perimeter is 2 × (length + width). Half the perimeter is therefore one length plus one width, and the width is what is left of that half once the length is taken away. Working: 30 ÷ 2 = 15 cm is one length added to one width, and 15 − 9 = 6. Answer: 6 cm. The distractors: 21 cm comes from taking the length off the whole perimeter, 30 − 9, so three sides are still counted in the figure that is written down; 12 cm comes from removing both lengths correctly, 30 − 2 × 9 = 12, and then recording that remainder as the width instead of halving it, because it is in fact the two widths together; 7.5 cm comes from dividing the perimeter by four, 30 ÷ 4, which is the calculation for the side of a square and throws away the length that was given.
Build your own mix at the worksheet builder.