Printable · GCSE Higher · ages 14-16
Geometry and measures worksheet — GCSE Higher
Fifteen questions across the geometry and measures statements at Higher tier. Choose the non-calculator filter to rehearse Paper 1, which counts for a third of the marks.
Calculator
Answer key: Geometry and measures worksheet — GCSE Higher
MathsUKwww.geekhero.co.uk
- (b) 6 m — Volume of a cuboid = length × width × height, so height = volume ÷ (length × width) = 360 ÷ (12 × 5) = 360 ÷ 60 = 6 m. A pupil who divides the volume by the length only gets 360 ÷ 12 = 30 m. A pupil who divides the volume by the width only gets 360 ÷ 5 = 72 m. A pupil who subtracts length × width from the volume instead of dividing gets 360 − 60 = 300 m. The correct height is 6 m.
- (c) £7.85 — Arc length = (90 ÷ 360) × 2 × 3.14 × 10 = 0.25 × 62.8 = 15.7 cm. Cost = 15.7 × £0.50 = £7.85. (£31.40 comes from finding the full circumference and forgetting the angle fraction; £15.70 comes from using the diameter, 20 cm, in place of the radius; £157.00 comes from multiplying the arc length by the radius instead of by the cost per centimetre.)
- (c) 10.4 cm — Method: rearrange Area = (1/2)ab sin C to make the unknown side the subject: b = 2 × Area ÷ (a × sin C). Working: b = 2 × 36 ÷ (9 × sin 50°) = 10.4 cm (1 d.p.). Answer: 10.4 cm. Forgetting to double the area before dividing gives b = 36 ÷ (9 × sin 50°) = 5.2 cm; using cos 50° instead of sin 50° gives b = 2 × 36 ÷ (9 × cos 50°) = 12.4 cm; and multiplying by sin 50° instead of dividing by it — inverting the rearrangement — gives b = 2 × 36 × sin 50° ÷ 9 = 6.1 cm. Always double the area before dividing, and check whether the unknown should be multiplied or divided by sin C once you've rearranged.
- (b) 3 — The real width is 0.6 × 500 = 300 cm, which converts to 3 m by dividing by 100. A candidate who uses the wrong side of the rectangle, 1.2 cm, instead of the 0.6 cm width, gets 1.2 × 500 = 600 cm = 6 m. A candidate who multiplies correctly but converts the 300 cm to metres by dividing by 1000 instead of 100 gets 0.3 m. A candidate who converts by dividing by 10 instead of 100 gets 30 m. The real width of the bay is 3 m.
- (d) 82.8° — Method: angle ABC is opposite the given side AC, so rearrange the cosine rule to cos B = (AB² + BC² − AC²) / (2 × AB × BC). Working: cos B = (3.5² + 2.8² − 4.2²) / (2 × 3.5 × 2.8), so angle ABC = 82.8°. Forgetting the negative sign in the rearrangement gives the supplementary angle 97.2°; leaving out the factor of 2 in the denominator gives 75.5°; and using AB and AC (the pair either side of angle A, not angle B) gives 41.4°, which is angle BAC, not angle ABC. Always check which angle sits opposite the side you left out of the pair you are dividing by.
- (a) 150° — The arc length is the same fraction of the circumference as the angle is of 360°. The full circumference is 2 × 3.14 × 6 = 37.68 cm, so the angle is 15.7 ÷ 37.68 × 360 = 150°. Treating the 6 cm as a diameter instead of a radius gives a circumference of 18.84 cm and an angle of 300°. Using π = 3 instead of the given 3.14 gives a circumference of 36 cm and an angle of 157°. Treating the fraction 15.7 ÷ 37.68 as being out of 100 rather than 360 gives about 42°.
- (b) 70 cm³ — Area of the triangular cross-section = base × height ÷ 2. Base × height = 3.5 × 4 = 14 cm², and half of that is 14 ÷ 2 = 7 cm². Volume of the prism = cross-sectional area × length = 7 × 10 = 70 cm³. A pupil who forgets to halve when finding the triangle's area gets 3.5 × 4 × 10 = 140 cm³. A pupil who correctly finds the cross-sectional area but forgets to multiply by the length stops at 7 cm³. A pupil who ignores the height altogether, multiplying base by length, gets 3.5 × 10 = 35 cm³. The correct volume is 70 cm³.
- (a) 6 — A cuboid has six faces in total: a top, a bottom, a front, a back, and two ends — each one is a rectangle in the net, giving six rectangles altogether. Choosing 3 counts only the three PAIRS of congruent rectangles (top/bottom, front/back, two ends) rather than all six individual faces. Choosing 5 forgets one face, as if the net were missing its lid. Choosing 12 is the number of edges of a cuboid, not the number of rectangles in its net.
- (b) 124.1° — Method: use the sine rule AB/sin(ACB) = AC/sin(ABC), since AB is opposite angle ACB and AC is opposite angle ABC. Working: sin(ACB) = AB × sin(ABC) / AC = 13 × sin 35° / 9 = 0.8285, which gives angle ACB = 55.9° or its supplement 180 − 55.9 = 124.1°; both of these give a valid triangle, and since angle ACB is obtuse the answer is 124.1°. Reporting the acute solution instead, without checking the word 'obtuse' in the question, gives 55.9°; putting the sides the wrong way round in the ratio, sin(ACB) = 9 × sin 35° / 13, gives 23.4°; and subtracting the acute solution and the given 35° from 180° as if angle ACB were the remaining triangle angle gives 89.1°. A given SSA fact always has two possible angle solutions unless the stem states which one is meant.
- (d) Triangle 2, by 3.6 cm² — Method: find both areas with 1/2ab sin C, then compare them. Working: area of triangle 1 = 1/2 × 10 × 13 × sin 64° = 58.4 cm²; area of triangle 2 = 1/2 × 11 × 12 × sin 70° = 62.0 cm²; triangle 2 is larger, by 62.0 − 58.4 = 3.6 cm². Getting the right difference but naming triangle 1 as the larger one, the subtraction done the wrong way round, gives 'Triangle 1, by 3.6 cm²'; leaving out the 1/2 when finding triangle 1's area (giving 116.8 cm² instead of 58.4 cm²) and then subtracting gives 'Triangle 1, by 54.8 cm²'; and using cos 64° instead of sin 64° for triangle 1 (giving 28.5 cm² instead of 58.4 cm²) gives 'Triangle 2, by 33.5 cm²'. Work out both areas fully and correctly before comparing which is bigger.
- (a) 89.6° — Angle PQR is at vertex Q, so the side opposite it is PR = 13 cm. Using the cosine rule rearranged for an angle: cos(PQR) = (121 + 49 − 169) ÷ (2 × 11 × 7) = 1 ÷ 154 = 0.0065. Taking the inverse cosine, angle PQR = 89.6° (1 d.p.). Using PR as one of the enclosing sides instead of as the opposite side, finding angle P instead of angle Q, gives (121 + 169 − 49) ÷ (2 × 11 × 13) = 241 ÷ 286 = 0.8427, and angle = 32.6°. Swapping the sign inside the bracket, computing 169 − 121 − 49 instead, gives −1 ÷ 154 = −0.0065, and angle = 90.4°. Using PR in the denominator instead of QR gives (121 + 49 − 169) ÷ (2 × 11 × 13) = 1 ÷ 286 = 0.0035, and angle = 89.8°. Keep PR as the opposite side, QR and PQ as the enclosing sides, and angle PQR comes to 89.6°.
- (c) 12.4 cm — Using the cosine rule, BC² = AB² + AC² − 2 × AB × AC × cos(A) = 9² + 6² − 2 × 9 × 6 × cos(110°) = 81 + 36 − 108 × cos(110°). Since cos(110°) ≈ −0.34202, 108 × cos(110°) ≈ −36.94, so BC² ≈ 117 + 36.94 = 153.94. Taking the square root, BC ≈ 12.4072, which rounds to 12.4 cm. 8.9 cm comes from treating cos(110°) as if it were positive (using +0.342 instead of −0.342), which wrongly subtracts instead of adds and gives BC² ≈ 80.06. 153.9 cm is BC² itself, rounded, with the square root never taken. 11.6 cm comes from leaving out the factor of 2 in the formula, computing BC² = 81 + 36 − 9 × 6 × cos(110°) ≈ 135.47 instead.
- (c) 155° — Turning clockwise adds to the bearing. Starting on a bearing of 065° and turning clockwise through 90° gives 065° + 90° = 155°. A candidate who instead subtracts, working out 90° − 65° = 25°, has performed the wrong operation, giving 025°. A candidate who turns anticlockwise instead of clockwise works out 065° − 90°, which gives a negative number, and adding 360° to fix this gives 335° — the bearing for turning the other way. A candidate who thinks turning does not change the bearing at all keeps the answer as 065°. The new bearing, turning clockwise, is 155°.
- (c) 40.5 kg — Since the statues are made from the same material, mass is proportional to volume, which scales with the cube of the length scale factor. The length scale factor is 45 ÷ 30 = 1.5, so the volume (and mass) scale factor is 1.5³ = 3.375. The larger statue's mass is 12 × 3.375 = 40.5 kg. 18 kg comes from multiplying by the length factor 1.5 directly. 27 kg comes from using the area scale factor 1.5² = 2.25 instead of the volume scale factor. 54 kg comes from treating 'cubed' as 'multiplied by 3', giving 1.5 × 3 = 4.5 instead of 1.5³.
- (d) 18.8 cm — Arc length is a fraction of the full circumference. Here 120 ÷ 360 = 1/3, and the full circumference is 2 × 3.14 × 9 = 56.52 cm, so the arc is 56.52 ÷ 3 = 18.84 cm, which rounds to 18.8 cm. Forgetting the fraction and giving the full circumference rounds to 56.5 cm. Using 9 cm as a diameter instead of a radius gives an arc of 9.4 cm. Using 120 ÷ 180 instead of 120 ÷ 360 for the fraction gives an arc of 37.7 cm.
Build your own mix at the worksheet builder.