Printable · GCSE Higher · ages 14-16
Geometry and measures worksheet — GCSE Higher
Fifteen questions across the geometry and measures statements at Higher tier. Choose the non-calculator filter to rehearse Paper 1, which counts for a third of the marks.
Calculator
Answer key: Geometry and measures worksheet — GCSE Higher
MathsUKwww.geekhero.co.uk
- (b) 25 minutes — Method: a rate in litres per minute can only be used on a volume measured in litres, so convert the tank first and then divide. Working: 1 m³ = 1000 litres, so the tank holds 0.45 × 1000 = 450 litres, and the time is 450 ÷ 18 = 25. Answer: 25 minutes. Using 1 m³ = 100 litres gives 45 ÷ 18 = 2.5 minutes. Using 1 m³ = 1 000 000 litres, which is the factor that turns cubic metres into cubic centimetres, gives 450 000 ÷ 18 = 25 000 minutes. Multiplying by the rate instead of dividing by it gives 450 × 18 = 8100.
- (a) Yes - SSS, the three side lengths all match — Bracket P's sides (12 cm, 16 cm, 20 cm) can each be matched to one of Bracket Q's sides (16 cm, 20 cm, 12 cm) — the same three lengths, just listed differently — so the brackets are congruent by SSS. SAS is wrong here because no angle is stated for either bracket, only three sides. The order the sides are listed in does not matter for SSS — only whether the SET of three lengths matches, and it does, so 'listed in a different order' is not a reason to say no. Nothing extra is needed: SSS proves congruence from side lengths alone, without any angles, so it can be determined.
- (c) 7.1 cm — Method: a shorter side is opposite the 45° angle and the hypotenuse is known, so sin θ = opposite ÷ hypotenuse gives that side directly. Working: sin 45° = x ÷ 10, so x = 10 × sin 45° = 7.071…, which is 7.1 to 1 decimal place. Answer: 7.1 cm. The distractors: 5.0 cm comes from halving the hypotenuse, which is the rule for the side opposite a 30° angle and not a 45° one; 14.1 cm comes from dividing by sin 45° instead of multiplying by it, which makes a shorter side longer than the hypotenuse; 10.0 cm comes from taking tan 45° = 1 and concluding that the shorter side matches the hypotenuse.
- (c) 6 cm — For a parallelogram, area = base × height, so height = area ÷ base = 54 ÷ 9 = 6 cm. 12 cm comes from using the triangle's reverse formula, height = 2 × area ÷ base, which does not apply to a parallelogram. 45 cm comes from subtracting the base from the area, 54 − 9, instead of dividing. 486 cm comes from multiplying the area by the base, 54 × 9, instead of dividing.
- (c) 1 : 300 — First convert both lengths to the same unit: 15 m = 1500 cm. The scale compares 5 cm on the drawing to 1500 cm in real life, so dividing both parts by 5 gives a scale of 1 : 300. A candidate who compares 5 to 15 without converting units gets 1 : 3. A candidate who converts 15 m to 150 cm, using the wrong conversion factor, gets 1 : 30. A candidate who converts 15 m to 15000 cm, again using the wrong conversion factor, gets 1 : 3000. The scale of the drawing is 1 : 300.
- (d) 6.7 cm — Volume of the sphere = (4/3)πr³ = (4/3) × 3.14 × 5³ = (4/3) × 3.14 × 125 = 523.33 cm³. Set this equal to the cylinder's volume πr²h: 523.33 = 3.14 × 25 × h = 78.5h. Divide: h = 523.33 ÷ 78.5 = 6.667 cm, which rounds to 6.7 cm. 1.7 cm comes from using the sphere's diameter, 10 cm, as the cylinder's radius: 523.33 ÷ (3.14 × 10²) = 1.7 cm.
- (b) 46.8 cm² — Method: for a parallelogram, not a triangle, the two sides and the angle between them give Area = ab sin C — there is no 1/2. Working: Area = 6 × 9 × sin 60° = 46.8 cm² (1 d.p.). Answer: 46.8 cm². Using the triangle formula, (1/2)ab sin C, on a parallelogram by mistake gives half the true area, 23.4 cm²; using cos 60° instead of sin 60° gives 27.0 cm²; and adding the two sides before multiplying by sin 60° gives 13.0 cm². A parallelogram is exactly two of the triangles this formula was built for, so never carry the 1/2 across from the triangle version.
- (a) 7.5 cm — Method: two sides and the angle between them are given, so use the cosine rule a² = b² + c² − 2bc cos A, with BC as the side facing the 68° angle. Working: BC² = 7.4² + 5.9² − 2 × 7.4 × 5.9 × cos 68° = 54.76 + 34.81 − 87.32 × 0.3746 = 89.57 − 32.71 = 56.86, and the square root of 56.86 is 7.5405. Answer: BC = 7.5 cm to 1 decimal place. The distractors: 11.1 cm comes from adding the last term instead of subtracting it, 89.57 + 32.71 = 122.28, the commonest sign slip on the cosine rule; 56.9 cm is the value of BC² written down as though it were BC, stopping one step before the square root; 2.9 cm comes from pressing sin instead of cos, using 87.32 × sin 68° = 80.96 as the term to subtract.
- (a) 24 — The display is 4 tins wide, 3 tins high and 2 tins deep, and every position in that block is filled, so the total number of tins is the product of all three measurements: 4 × 3 × 2 = 24. "12" comes from multiplying only the width and height shown in the front elevation (4 × 3), forgetting the depth entirely. "9" comes from adding the three measurements (4 + 3 + 2) instead of multiplying them. "6" comes from multiplying only the height and depth (3 × 2), forgetting the width shown by the front elevation.
- (c) 460 g — Each division is 20 g, so three divisions past the mark is 3 × 20 = 60 g. Adding this to the 400 g mark gives 400 + 60 = 460 g. Treating each division as worth 1 g instead of 20 g gives 400 + 3 = 403 g. Working out the extra amount correctly but forgetting to add the 400 g mark gives just 60 g. Treating each division as worth 10 g instead of 20 g gives 400 + 30 = 430 g.
- (b) £33.60 — The area of the parallelogram flower bed is base × height = 3.5 × 2 = 7 m². The cost is 7 × £4.80 = £33.60. £16.80 comes from using the triangle formula instead of the parallelogram formula: 3.5 × 2 = 7, and half of 7 is 3.5 m², then 3.5 × £4.80 = £16.80. £26.40 comes from adding the base and height, 3.5+2 = 5.5, instead of multiplying them, then multiplying by £4.80. £7.00 correctly finds the area, 7 m², but forgets to multiply it by the cost per m².
- (a) 188.4 cm² — Curved surface area of a cone = πrl. With r = 6 cm, l = 10 cm and π = 3.14, curved surface area = 3.14 × 6 × 10 = 188.4 cm². A student who uses the cylinder's curved surface area formula, 2πrl, instead of the cone's gets 2 × 3.14 × 6 × 10 = 376.8 cm². A student who uses the circle-area formula πr² instead of πrl gets 3.14 × 36 = 113.04 cm². A student who multiplies r × l but leaves out π entirely gets 6 × 10 = 60 cm².
- (a) 1023 m² — Method: split the quadrilateral along the diagonal AC into two triangles. Triangle ABC has two sides and the angle between them, so the cosine rule gives AC and the area formula gives its area; triangle ACD then has three known sides, so the cosine rule gives an angle and the area formula gives its area. Working: AC² = 40² + 32² − 2 × 40 × 32 × cos 95° = 1600 + 1024 + 223.12 = 2847.12, so AC = 53.358 m. The area of triangle ABC is 1/2 × 40 × 32 × sin 95° = 640 × 0.99619 = 637.56 m². In triangle ACD, cos ADC = (25² + 36² − 2847.12) ÷ (2 × 25 × 36) = (1921 − 2847.12) ÷ 1800 = −0.51451, so angle ADC = 120.965° and sin ADC = 0.85748, giving an area of 1/2 × 25 × 36 × 0.85748 = 385.87 m². The total is 637.56 + 385.87 = 1023.43. Answer: the field has an area of 1023 m² to the nearest square metre. The distractors: 1071 m² comes from taking cos 95° as positive, so the diagonal is found as 49.00 m instead of 53.358 m and the second triangle comes out too large; 2047 m² comes from leaving the factor 1/2 out of both area calculations; 638 m² is the area of triangle ABC alone, written down by a candidate who finds the diagonal and then forgets that the second triangle is part of the field.
- (b) 10 cm — Arc length = (angle ÷ 360) × 2 × π × r, so 15.7 = (90 ÷ 360) × 2 × 3.14 × r = 1.57r, giving r = 15.7 ÷ 1.57 = 10 cm. (2.5 cm comes from forgetting the angle fraction and dividing by 2π alone; 20 cm comes from leaving out the factor of 2 in the arc length formula before dividing; 5 cm comes from dividing the arc length by π alone, ignoring both the angle fraction and the factor of 2.)
- (c) 100.5 m — The curved part of a semicircular bend is half of a full circle's circumference. The full circumference would be 2 × 3.14 × 32 = 200.96 m, and half of that is 200.96 ÷ 2 = 100.48 m, which rounds to 100.5 m. Choosing 201.0 m uses the FULL circumference, forgetting to halve it for a semicircle. Choosing 50.2 m halves the radius as well as taking a semicircle, using 3.14 × 16 = 50.24 m instead of the correct radius of 32 m. Choosing 64.0 m uses the diameter, 2 × 32 = 64, as if it were the curved length, ignoring π and the semicircle shape entirely.
Build your own mix at the worksheet builder.