Printable · GCSE Higher · ages 14-16
Geometry and measures worksheet — GCSE Higher
Fifteen questions across the geometry and measures statements at Higher tier. Choose the non-calculator filter to rehearse Paper 1, which counts for a third of the marks.
Calculator
Answer key: Geometry and measures worksheet — GCSE Higher
MathsUKwww.geekhero.co.uk
- (d) 10.3 m — By Pythagoras' theorem, the hypotenuse = √(5² + 9²) = √(25 + 81) = √106 = 10.29...≈ 10.3 m. "106 m" is the value under the square root sign, correct as far as it goes but with the final square root step left out. "14 m" comes from adding the two shorter sides, 5 + 9, instead of using Pythagoras' theorem at all. "10.2 m" comes from rounding 10.29...m down to 10.2 instead of correctly rounding it up to 10.3.
- (d) 6 cm — Volume = πr²h, so height = volume ÷ (πr²) = 471 ÷ (3.14 × 25) = 471 ÷ 78.5 = 6 cm. (30 cm comes from dividing by πr instead of πr², missing one factor of the radius; 150 cm comes from dividing by π only, without using r² at all; 24 cm comes from treating the given 5 cm as a diameter and using a radius of 2.5 cm instead.)
- (b) x = 5 — Every point on a vertical line has the same x-coordinate, so the equation of a vertical line through (5, 2) is x = 5. "y = 5" mixes up the coordinates, using the x-value of 5 to write a y-equation. "y = 2" is the equation of the horizontal line through (5, 2), not the vertical one. "x = 2" uses the correct letter but the wrong coordinate, the y-value of 2 instead of the x-value of 5.
- (c) 460 g — Each division is 20 g, so three divisions past the mark is 3 × 20 = 60 g. Adding this to the 400 g mark gives 400 + 60 = 460 g. Treating each division as worth 1 g instead of 20 g gives 400 + 3 = 403 g. Working out the extra amount correctly but forgetting to add the 400 g mark gives just 60 g. Treating each division as worth 10 g instead of 20 g gives 400 + 30 = 430 g.
- (d) 18.8 cm — Arc length is a fraction of the full circumference. Here 120 ÷ 360 = 1/3, and the full circumference is 2 × 3.14 × 9 = 56.52 cm, so the arc is 56.52 ÷ 3 = 18.84 cm, which rounds to 18.8 cm. Forgetting the fraction and giving the full circumference rounds to 56.5 cm. Using 9 cm as a diameter instead of a radius gives an arc of 9.4 cm. Using 120 ÷ 180 instead of 120 ÷ 360 for the fraction gives an arc of 37.7 cm.
- (d) 706.5 cm² — Area of a circle = πr². With r = 15 cm and π = 3.14, area = 3.14 × 15² = 3.14 × 225 = 706.5 cm². A student who uses the circumference formula 2πr instead of the area formula gets 2 × 3.14 × 15 = 94.2 cm². A student who uses πr instead, forgetting to double, gets 3.14 × 15 = 47.1 cm². A student who squares the diameter (30 cm) instead of the radius gets 3.14 × 900 = 2826.0 cm².
- (b) 7.4 — Method: AB is opposite angle ACB and AC is opposite angle ABC, so the sine rule gives AB/sin(ACB) = AC/sin(ABC). Working: (2x + 1)/sin 48° = (3x − 2)/sin 72°; cross-multiplying and collecting the x terms gives x = 7.4. Using angle BAC = 180° − 72° − 48° = 60° in place of angle ABC in the ratio gives x = 4.7; ignoring the sine rule altogether and solving 2x + 1 = 3x − 2 as if the two sides were simply equal gives x = 3.0; and pairing each side with the wrong angle — AB with sin 72° and AC with sin 48° — gives x = 1.9. Each side in the sine rule must be paired with the sine of the angle directly opposite it.
- (b) 32 cm² — The area of a trapezium is half of the sum of the parallel sides, multiplied by the height. Add the parallel sides: 6 + 10 = 16. Multiply by the height: 16 × 4 = 64. Half of 64 is 32 cm². 64 cm² forgets to halve and just gives (6+10)×4. 8 cm² averages the two parallel sides, (6+10)÷2 = 8, but forgets to multiply by the height. 20 cm² treats it as a triangle using only the longer parallel side as the base: half of 10 × 4.
- (a) 24 — The display is 4 tins wide, 3 tins high and 2 tins deep, and every position in that block is filled, so the total number of tins is the product of all three measurements: 4 × 3 × 2 = 24. "12" comes from multiplying only the width and height shown in the front elevation (4 × 3), forgetting the depth entirely. "9" comes from adding the three measurements (4 + 3 + 2) instead of multiplying them. "6" comes from multiplying only the height and depth (3 × 2), forgetting the width shown by the front elevation.
- (a) 28.1° — The angle a line makes with the horizontal plane lies in the right-angled triangle formed by the vertical rise, the horizontal distance travelled, and the line itself. The horizontal distance from A to B is √(9² + 12²) = √(81 + 144) = √225 = 15, using only the x- and y-coordinates. The vertical rise is the z-coordinate, 8, so tan(angle) = 8 ÷ 15, giving angle = 28.1° (1 d.p.). Inverting the ratio, tan(angle) = 15 ÷ 8, gives 61.9° instead — the complement of the angle, not the angle with the horizontal. Using only the x-coordinate as if it were the whole horizontal distance, tan(angle) = 8 ÷ 9, gives 41.6°. Using the y-coordinate alone in the same way, tan(angle) = 8 ÷ 12, gives 33.7°.
- (d) £100.48 — Area of the rug = (angle ÷ 360) × π × r² = (180 ÷ 360) × 3.14 × 16 = 0.5 × 50.24 = 25.12 m². Cost = 25.12 × £4 = £100.48. (£200.96 comes from finding the area of a full circle, 3.14 × 16 = 50.24 m², and forgetting the angle fraction before costing it; £25.12 comes from forgetting to square the radius, using 0.5 × 3.14 × 4 = 6.28 m², and then costing that; £50.24 comes from using the arc length formula, 0.5 × 2 × 3.14 × 4 = 12.56, in place of the area, and costing that.)
- (d) 30.2 cm² — Method: with two sides and the angle between them, use Area = (1/2)ab sin C. Working: Area = 1/2 × 9.4 × 7.2 × sin 63° = 30.2 cm² (1 d.p.). Answer: 30.2 cm². Leaving out the 1/2 altogether gives 60.3 cm²; using cos 63° instead of sin 63° gives 15.4 cm²; and squaring one side instead of multiplying the two different given sides together gives 39.4 cm². Always check you are using sin, not cos, and that the 1/2 is there before you multiply the two given sides together.
- (d) 7.7 m — The horizontal distance is adjacent to the 50° angle and the zip wire is the hypotenuse, so horizontal distance = 12 × cos 50° = 12 × 0.6428... = 7.71...≈ 7.7 m. "9.2 m" uses the sine ratio instead of cosine, 12 × sin 50° = 9.19...≈ 9.2 m, which actually finds the vertical drop of the zip wire, not the horizontal distance. "15.7 m" comes from dividing by the sine ratio instead of multiplying by the cosine ratio, 12 ÷ sin 50° = 15.66...≈ 15.7 m, both the wrong operation and the wrong ratio. "12.0 m" simply uses the length of the zip wire itself as the horizontal distance, ignoring the angle of 50° altogether.
- (c) 22.3 km — The bearing of E from D is 065°, so the bearing of D from E (the back bearing) is 065° + 180° = 245°. The bearing of F from E is 165°, so the angle at E between ED and EF is 245° − 165° = 80°. Using the cosine rule, DF² = DE² + EF² − 2 × DE × EF × cos(80°) = 14² + 20² − 2 × 14 × 20 × cos(80°) = 196 + 400 − 560 × cos(80°). Since cos(80°) ≈ 0.17365, 560 × cos(80°) ≈ 97.24, so DF² ≈ 596 − 97.24 = 498.76. Taking the square root, DF ≈ 22.333, which rounds to 22.3 km. 26.3 km comes from using 100° as the angle at E — the difference between the two given bearings taken directly (165° − 65°) without converting to the back bearing first. 498.8 km is DF² itself, rounded, with the square root never taken. 23.4 km comes from leaving out the factor of 2 in the cosine rule formula, computing DF² = 196 + 400 − 14 × 20 × cos(80°) ≈ 547.38 instead.
- (a) 8,000,000 cm³ — Method: change the edge length into centimetres first and then cube it, because 1 m = 100 cm and a volume needs that conversion applied to all three dimensions. Working: 2 m = 2 × 100 = 200 cm, so the volume is 200 × 200 × 200. 200 × 200 = 40,000 and 40,000 × 200 = 8,000,000. Answer: 8,000,000 cm³. The distractors: 8,000 cm³ comes from converting 2 m to 20 cm and cubing that; 80,000 cm³ comes from cubing in metres to get 8 m³ and then multiplying by 10,000, the conversion factor for an area rather than the 1,000,000 a volume needs; 8 cm³ comes from cubing the 2 without converting at all and simply writing cm³ because the question asked for that unit.
Build your own mix at the worksheet builder.