Printable · GCSE Higher · ages 14-16
Geometry and measures worksheet — GCSE Higher
Fifteen questions across the geometry and measures statements at Higher tier. Choose the non-calculator filter to rehearse Paper 1, which counts for a third of the marks.
Non-calculator
Answer key: Geometry and measures worksheet — GCSE Higher
MathsUKwww.geekhero.co.uk
- (a) Yes - SSS, the three side lengths all match — Bracket P's sides (12 cm, 16 cm, 20 cm) can each be matched to one of Bracket Q's sides (16 cm, 20 cm, 12 cm) — the same three lengths, just listed differently — so the brackets are congruent by SSS. SAS is wrong here because no angle is stated for either bracket, only three sides. The order the sides are listed in does not matter for SSS — only whether the SET of three lengths matches, and it does, so 'listed in a different order' is not a reason to say no. Nothing extra is needed: SSS proves congruence from side lengths alone, without any angles, so it can be determined.
- (d) 6√3 cm — Method: AB lies alongside the 30° angle at A and AC is the hypotenuse, so the ratio needed is cosine: cos 30° = AB ÷ AC. Working: the exact value of cos 30° is √3/2, so AB = 12 × √3 ÷ 2, and half of 12 is 6. Answer: AB = 6√3 cm, which is about 10.4 cm. Using sine by mistake gives 12 × 1/2 = 6 cm, which is the length of BC rather than AB. Using tan 30° = 1/√3 gives 12 ÷ √3, which is 4√3 cm. Remembering cos 30° as √3 rather than as √3 halved gives 12√3 cm, longer than the hypotenuse and so impossible.
- (b) (3, −5) — Method: apply the rotation to the point first, then translate the image, in the order the question gives them. Working: rotating (4, 1) by 90° clockwise about the origin sends (x, y) to (y, −x), so (4, 1) becomes (1, −4). Translating (1, −4) by the vector (2, −1) gives 1 + 2 = 3 and −4 − 1 = −5, so the final image is (3, −5). Answer: (3, −5). Use the CLOCKWISE rule, (x, y) → (y, −x), not the anticlockwise one, and apply the rotation before the translation, exactly as the question states them: reversing the order or the direction of turn both land on a different point.
- (a) 2√3/3 — tan 30° = √3/3, so tan 30° + tan 30° = 2 × √3/3 = 2√3/3. √3 comes from wrongly treating tan 30° + tan 30° as tan(30° + 30°) = tan 60° = √3 — adding angles is not the same as adding ratios. √3/3 comes from forgetting to double the value and just writing down tan 30° on its own. 2√3 comes from doubling the numerator of √3/3 but forgetting to keep the denominator of 3.
- (d) 12 cm — Since DE is parallel to BC, triangle ADE is similar to triangle ABC (the two triangles share angle A, and the parallel lines make the angles at D and E equal to the angles at B and C). The whole side AB = AD + DB = 3 + 6 = 9 cm. The scale factor from the small triangle to the large triangle is AB ÷ AD = 9 ÷ 3 = 3, so BC = DE × 3 = 4 × 3 = 12 cm. Scaling by DB ÷ AD instead of AB ÷ AD gives 4 × (6 ÷ 3) = 8 cm. Adding DB directly onto DE, instead of scaling, gives 4 + 6 = 10 cm. Treating the triangles as congruent rather than similar, so assuming corresponding sides are simply equal, gives BC = DE = 4 cm.
- (a) 250° — The back bearing (the bearing of A from B) differs from the bearing of B from A by exactly 180°. Because the given bearing, 070°, is less than 180°, add 180°: 070 + 180 = 250°, so the bearing of A from B is 250°. Choosing 180° assumes the back bearing is always exactly 180°, ignoring the original bearing altogether. Choosing 110° comes from subtracting 180° from 070° and dropping the negative sign (070 − 180 = −110) instead of adding 180°. Choosing 160° comes from adding only 90° instead of 180° (070 + 90 = 160).
- (b) 28 — Method: total bricks = (number of squares in the footprint) × (the height of the wall in bricks). Working: the footprint has the row of 5 squares plus the 2 squares in the arm that stands out from the middle of that row, and they do not overlap, giving 5 + 2 = 7 squares; multiplying by the height of 4 bricks gives 7 × 4 = 28. Answer: 28. The distractors: 20 comes from using only the row of 5 and ignoring the arm (5 × 4). 24 comes from treating the bottom square of the arm as if it were one of the row's own squares, so the arm is counted as adding only 1 new square instead of 2 (5 + 1 = 6, then 6 × 4). 32 comes from counting the square of the row directly below the arm a second time as part of the arm (5 + 3 = 8, then 8 × 4).
- (d) (1/2)a + (1/2)c — Method: X is the midpoint of AC, so OX = OA + (1/2)AC, with AC = c − a. Working: OX = a + 1/2(c − a) = a − (1/2)a + (1/2)c = (1/2)a + (1/2)c. Answer: OX = (1/2)a + (1/2)c. Since OB = a + c, this is exactly half of OB, so OX = (1/2)OB, meaning X lies on OB at its midpoint too — the two diagonals bisect each other. Forgetting to halve AC at all gives a + c, which is OB itself, not its midpoint; halving only the c-term gives (1/2)a + c; and a sign error on the c-term gives (1/2)a − (1/2)c. Halve the whole of AC, both terms together, and add it to OA rather than to a alone.
- (d) 71° — Alternate angles between parallel lines are equal. Since angle HMN and angle MNK are alternate angles, angle MNK = angle HMN = 71°.
- (c) A line has no endpoints; a segment has two — A line extends without end in both directions, whereas a line segment is the part of a line between two specific fixed endpoints, so 'a line has no endpoints; a segment has two' is correct. 'A line has two endpoints; a segment has none' reverses these two definitions, so it is wrong. 'A line segment is always curved' is wrong because a line segment is straight, not curved, and does not extend infinitely. 'A line segment is a closed shape' is wrong because a line segment is a straight length between two points, not a polygon.
- (a) (−2, 6) — Translating by the vector (−5, 4) means adding −5 to the x-coordinate and adding 4 to the y-coordinate: (3 + (−5), 2 + 4) = (−2, 6). (8, 6) comes from treating −5 as +5, adding instead of subtracting on the x-coordinate. (−2, −2) keeps the x-coordinate correct but subtracts 4 from the y-coordinate instead of adding it. (7, −3) comes from swapping the two components of the vector, applying 4 to the x-coordinate and −5 to the y-coordinate.
- (d) 13 — Method: OP and PQ meet at a right angle because of the tangent–radius fact, so triangle OPQ is right-angled at P; use Pythagoras' theorem. Working: OQ² = OP² + PQ² = 5² + 12² = 25 + 144 = 169; OQ = √169 = 13. A student who answers 17 has simply added the two given lengths (5 + 12) instead of using Pythagoras' theorem. A student who answers 7 has subtracted the two given lengths (12 − 5) instead of using Pythagoras' theorem. A student who answers 144 has correctly squared 12 but stopped there, forgetting to add 5² and take the square root. Answer: 13 cm.
- (a) 9 — A cube has 9 planes of symmetry in total: 3 that pass through the middles of pairs of opposite faces, and 6 more that pass through pairs of opposite edges diagonally. A candidate who counts only the 3 face-to-face planes — which is correct for a cuboid with three different edge lengths, but forgets that a cube's equal edges create 6 more diagonal planes — answers 3. A candidate who counts only the 6 diagonal planes and forgets the 3 face-to-face ones answers 6. A candidate who confuses the number of planes of symmetry with the number of edges on a cube answers 12. The correct total for a cube is 9.
- (a) 9 — AB is a vertical segment, since A and B share the x-coordinate 1, and its length is the difference in y-coordinates: 5 − 1 = 4. BC is a horizontal segment, since B and C share the y-coordinate 5, and its length is the difference in x-coordinates: 6 − 1 = 5. The total path length is 4 + 5 = 9. 20 comes from multiplying the two lengths, 4 × 5, instead of adding them. 5 is only the length of BC, forgetting to include AB. 4 is only the length of AB, forgetting to include BC.
- (d) 2/3 — Method: since A is the midpoint of OE, OE = 2a, so E = 2a. Since FB is twice AF, F is 1/3 of the way along AB from A, so F = a + 1/3(b − a) = (2/3)a + (1/3)b. G is the midpoint of OB, so G = (1/2)b. Working: EF = F − E = (2/3)a + (1/3)b − 2a = −(4/3)a + (1/3)b, and EG = G − E = −2a + (1/2)b. Comparing term by term, 2/3 × (−2a + (1/2)b) = −(4/3)a + (1/3)b, which matches EF exactly — the same scalar works on both the a-term and the b-term, so the two vectors are parallel, and since they share the point E the three points are collinear. Answer: k = 2/3, so E, F and G lie on a straight line. Giving 1/3 instead is the scalar linking F to G (FG = (1/3)EG), not E to F; giving 3/2 is the reciprocal — it is EG that equals 3/2 × EF, not the other way round, since EF = k × EG was what was asked for; and giving 4/3 is EF's a-coefficient read off raw, without ever dividing it by EG's a-coefficient to form the comparison. Always match the direction of the scalar to the vectors exactly as the question states them.
Build your own mix at the worksheet builder.