Printable · GCSE Higher · ages 14-16
Geometry and measures worksheet — GCSE Higher
Fifteen questions across the geometry and measures statements at Higher tier. Choose the non-calculator filter to rehearse Paper 1, which counts for a third of the marks.
Non-calculator
Answer key: Geometry and measures worksheet — GCSE Higher
MathsUKwww.geekhero.co.uk
- (b) 25 minutes — Method: a rate in litres per minute can only be used on a volume measured in litres, so convert the tank first and then divide. Working: 1 m³ = 1000 litres, so the tank holds 0.45 × 1000 = 450 litres, and the time is 450 ÷ 18 = 25. Answer: 25 minutes. Using 1 m³ = 100 litres gives 45 ÷ 18 = 2.5 minutes. Using 1 m³ = 1 000 000 litres, which is the factor that turns cubic metres into cubic centimetres, gives 450 000 ÷ 18 = 25 000 minutes. Multiplying by the rate instead of dividing by it gives 450 × 18 = 8100.
- (a) A square's diagonals are equal in length — A square has two pairs of parallel sides, four equal sides, and diagonals that are equal in length and cross at right angles. This tile's diagonals are not equal, so it is a rhombus that is not a square.
- (b) 46.8 cm² — Method: for a parallelogram, not a triangle, the two sides and the angle between them give Area = ab sin C — there is no 1/2. Working: Area = 6 × 9 × sin 60° = 46.8 cm² (1 d.p.). Answer: 46.8 cm². Using the triangle formula, (1/2)ab sin C, on a parallelogram by mistake gives half the true area, 23.4 cm²; using cos 60° instead of sin 60° gives 27.0 cm²; and adding the two sides before multiplying by sin 60° gives 13.0 cm². A parallelogram is exactly two of the triangles this formula was built for, so never carry the 1/2 across from the triangle version.
- (c) 14.7 cm — The scale factor from the smaller tile to the larger tile is 7 ÷ 4 = 1.75, so the larger side is 8.4 × 1.75 = 14.7 cm. '4.8 cm' comes from scaling by 4 ÷ 7 instead, using the ratio the wrong way round. '11.4 cm' comes from adding the difference between the ratio numbers, 7 − 4 = 3, onto 8.4, instead of scaling. '58.8 cm' comes from multiplying by 7 on its own, using a ratio number as the scale factor instead of working out 7 ÷ 4 = 1.75 first.
- (a) 62° — Angle KPQ and angle MQP are co-interior (allied) angles between parallel lines, so they add up to 180°: angle MQP = 180° − 118° = 62°. 118° comes from treating the angles as equal, as if this were a corresponding or alternate angle pair, instead of using the co-interior rule. 90° comes from wrongly assuming the crossing line meets JK and LM at right angles. 59° comes from halving 118° instead of subtracting it from 180°.
- (b) 320° — A bearing is always measured clockwise from north. An angle measured anticlockwise must be converted by subtracting it from 360°: 360 − 40 = 320°, so the bearing is 320°. Choosing 040° treats the anticlockwise angle as if it were already a clockwise bearing, without converting it. Choosing 220° adds 180° to the angle, mixing this up with a back-bearing calculation (40 + 180 = 220). Choosing 400° adds the angle to 360° instead of subtracting it (40 + 360 = 400), giving a bearing greater than a full turn.
- (c) Two angles and one side are known; x is another side — The sine rule needs a matching pair, a side and the angle opposite it, that you already know, so you can set up a ratio with the unknown. When two angles and one side are known, you can find the third angle from the angle sum, giving you an angle opposite the known side and an angle opposite x: the sine rule applies directly. When all three sides are known and x is an angle, there is no side-angle pair available at all, so the cosine rule, rearranged for an angle, is what's needed instead. When two sides and the included angle are known and x is the third side, again there is no matching side-angle pair yet, so the cosine rule finds the third side directly. When two sides and the included angle are known and x is one of the other angles, you still have no side-angle pair to start from — the cosine rule has to be used first, to find the third side, before any angle can be found. Only the two-angles-and-a-side case hands you a ready-made pair, which is exactly what the sine rule needs.
- (c) (1, 0) — To enlarge about a centre other than the origin, find the vector from the centre to the point, scale that vector, then add it back to the centre. The vector from (2, 2) to A(4, 6) is (2, 4). Scaling by −1/2 gives (−1, −2). Adding this to the centre (2, 2) gives the image point (1, 0). (3, 4) comes from using +1/2 instead of −1/2, so the image lands on the same side as A instead of the opposite side. (−2, −3) comes from scaling A's coordinates directly about the origin, ignoring that the centre is (2, 2). (−2, −6) comes from using a scale factor of −2 instead of −1/2.
- (a) SSA - not sufficient to prove congruence — The angle given, angle A, is not the angle between sides AB and BC — it is not the included angle — so this data is SSA (side, side, angle), which is not sufficient to prove congruence on its own; two triangles can share this SSA information without being congruent. SAS is wrong because the given angle is not the one included between the two given sides. ASA is wrong because only one angle (A) is given, not two. AAS is wrong for the same reason — only one angle is given, not two.
- (d) 63.6 — Method: the three angles inside the triangle formed by the two ladders and the ground add up to 180°. Working: 180 − 58.2 − 58.2 = 63.6. Answer: 63.6°. A candidate who assumes the top angle equals the base angles gives 58.2. A candidate who subtracts only one base angle from 180°, working out 180 − 58.2, gets 121.8. A candidate who doubles the base angle instead of subtracting it twice from 180°, working out 2 × 58.2, gets 116.4.
- (d) 2 — Method: a point is invariant under a reflection exactly when it lies on the mirror line, so check each vertex's coordinate against the line's equation. Working: the line of reflection is x = 3, so a vertex is invariant only if its x-coordinate equals 3. (3, 1) has x = 3, so it is invariant. (3, 5) has x = 3, so it is also invariant. (6, 1) has x = 6, so it is not invariant, since 6 is not equal to 3. Two of the three vertices are invariant. Answer: 2. Check EVERY vertex against the mirror line's equation rather than assuming a shape either keeps all its vertices fixed or none of them: a vertex is invariant only when it sits exactly on the line, and here two do and one does not.
- (d) A rectangle — Method: to find the plan view, work out the outline traced when looking straight down onto the solid from directly above, not the outline shown in the angled sketch. Working: this solid has two identical flat round ends joined by one curved surface, and it is lying on its side rather than standing upright; viewed from above, the curved surface gives two straight edges running the full length of the solid, the width of the round ends apart, and each flat round end — seen edge-on from directly above — also becomes a straight edge of that same width, with no curve remaining. Four straight edges, with opposite sides equal and meeting at right angles, form a rectangle. Answer: a rectangle. The distractors: a circle comes from picturing the solid as if it were standing upright on one of its flat ends, giving the plan of an upright version instead of working out the plan of the solid as it actually lies. An oval comes from copying the foreshortened shape of a round end as it is drawn in the angled sketch, instead of working out the true shape seen from directly above, which has no such foreshortening. A rectangle with rounded ends comes from carrying the curve of the round ends over into the plan view, when in fact a flat round end viewed edge-on from directly above shows no curve at all, only a straight edge.
- (d) 6 cm — Method: CH cuts the triangle into two smaller right-angled triangles, so Pythagoras' theorem can be written in each of the three right-angled triangles and the results combined. Working: HB = 12 − 3 = 9 cm. In triangle ACH, CH² = AC² − 3² = AC² − 9; in triangle CHB, CH² = CB² − 9² = CB² − 81. Setting those equal gives AC² − 9 = CB² − 81. In triangle ABC, AC² + CB² = 12² = 144, so CB² = 144 − AC². Substituting gives AC² − 9 = 144 − AC² − 81, so 2 × AC² = 72 and AC² = 36, giving AC = 6. Answer: 6 cm. The distractors: 36 cm comes from stopping at AC² = 36 and never taking the square root; 9 cm is HB, the other part of the hypotenuse, written down in place of AC; 4 cm comes from working out 12 ÷ 3, treating AH as a scale factor between the two triangles rather than as a length.
- (b) Yes — OA = OC (radii), so the base angles are equal. — Method: check the definition of a radius and the isosceles triangle property the step relies on. Working: every radius of a circle has the same length, so OA = OC regardless of where A and C sit on the circle — this alone makes triangle OAC isosceles, and the base angles opposite the two equal sides, angle OAC and angle OCA, must be equal. The verdict is Yes, for exactly that reason. Claiming OA and OC are only equal if they are drawn to 'the very same point' misunderstands what a radius is — A and C can be any two points on the circle and OA still equals OC. Claiming the triangle is isosceles because angle AOC is 90° reverses the logic: nothing in the step has fixed angle AOC at 90°, and even if it had, that alone would not explain why OA = OC. Claiming the triangle would need to be equilateral confuses isosceles (two equal sides) with equilateral (three equal sides) — only two sides, OA and OC, are being compared here.
- (a) 65° — OT and OC are both radii, so triangle OTC is isosceles with OT = OC, and its base angles are equal: angle OTC = angle OCT = (180° − 130°) ÷ 2 = 25°. A tangent is perpendicular to the radius at the point of contact, so angle OTP = 90°. Since C lies inside angle OTP, the chord TC splits this right angle into angle OTC and angle PTC, so angle PTC = angle OTP − angle OTC = 90° − 25° = 65°. Stopping after finding the base angle of the isosceles triangle, without subtracting it from the right angle at T, leaves 25° instead of the angle actually asked for. Adding the base angle to the right angle instead of subtracting it, 90° + 25° = 115°, reverses the direction the two angles combine in. Finding the sum of the two base angles of the isosceles triangle, 180° − 130° = 50°, and stopping there, gives another wrong value entirely.
Build your own mix at the worksheet builder.