Printable · GCSE Higher · ages 14-16
Geometry and measures worksheet — GCSE Higher
Fifteen questions across the geometry and measures statements at Higher tier. Choose the non-calculator filter to rehearse Paper 1, which counts for a third of the marks.
Non-calculator
Answer key: Geometry and measures worksheet — GCSE Higher
MathsUKwww.geekhero.co.uk
- (b) 320° — A bearing is always measured clockwise from north. An angle measured anticlockwise must be converted by subtracting it from 360°: 360 − 40 = 320°, so the bearing is 320°. Choosing 040° treats the anticlockwise angle as if it were already a clockwise bearing, without converting it. Choosing 220° adds 180° to the angle, mixing this up with a back-bearing calculation (40 + 180 = 220). Choosing 400° adds the angle to 360° instead of subtracting it (40 + 360 = 400), giving a bearing greater than a full turn.
- (b) P, since OP = 5 and OQ = 6 — Using the distance formula, OP = √(3² + 4²) = √(9 + 16) = √25 = 5, and OQ = √(6² + 0²) = √36 = 6. Since 5 is less than 6, P is closer to the origin. Naming Q as closer, with OQ = 5 and OP = 6, has the two distances swapped around the wrong point. Naming P as closer but with OP = 6 and OQ = 5 also has the two values swapped, even though it names the right point. The distances are not equal, since 5 is not the same as 6, so P and Q are not equally distant from the origin.
- (a) 110° — The truss is isosceles, so its two base angles are equal; since the three angles of the triangle add up to 180° and the apex is 40°, each base angle is (180 − 40) ÷ 2 = 70°. The angle between the sloping edge and the joist, extended beyond the base of the truss, sits on a straight line with that 70° base angle, and angles on a straight line add up to 180°, so the required angle is 180 − 70 = 110°. "70°" comes from stopping after finding the base angle and giving it directly, without also using the straight-line fact to find the angle on the OUTSIDE of the truss. "140°" comes from doubling the base angle instead of using the straight-line fact. "20°" comes from taking half of the apex angle (40° ÷ 2), mistaking it for the required angle instead of properly using the triangle's angle sum.
- (d) (6, 2) — Applying the first vector: (2, 1) + (5, −3) = (7, −2), which is the warehouse. Applying the second vector: (7, −2) + (−1, 4) = (6, 2), the delivery address. '(7, −2)' stops at the warehouse and forgets the second flight. '(8, −6)' comes from adding (1, −4) instead of (−1, 4) for the second vector, getting both signs wrong. '(11, −3)' comes from swapping the components of the second vector to (4, −1) before adding.
- (a) 080° — The back bearing differs from the given bearing by 180°. Because 260° is greater than 180°, subtract 180°: 260 − 180 = 80°, so the bearing of A from B is 080°. Choosing 440° adds 180° instead of subtracting it, even though the result would be more than a full turn (260 + 180 = 440). Choosing 180° assumes the back bearing is always exactly 180°, ignoring the original bearing altogether. Choosing 100° comes from measuring the reflex angle the other way round the circle (360 − 260 = 100) instead of applying the 180° back-bearing rule.
- (a) 245 m² — Method: for similar figures the ratio of the areas is the square of the ratio of the lengths, so multiply the smaller area by the square of the length scale factor. Working: the length scale factor is 7 ÷ 3, so the area scale factor is 49 ÷ 9, and the larger area is 45 × 49 ÷ 9 = 5 × 49 = 245. Answer: 245 m². The distractors: 105 m² comes from multiplying by the length scale factor 7 ÷ 3 instead of by its square, the commonest slip on this topic; 315 m² comes from multiplying by 7 and forgetting to divide by 3; 405 m² comes from multiplying by 3² = 9, squaring the wrong part of the ratio.
- (b) 10.5 — Method: multiply the drawing length by the scale factor to get the real length. Working: 7 cm × 1.5 = 10.5 m. A student who answers 8.5 has added the scale factor to the drawing length instead of multiplying (7 + 1.5). A student who answers 14 has rounded the scale factor up to 2 before multiplying. A student who answers 3.5 has divided the drawing length by 2 instead of multiplying it by 1.5. Answer: 10.5 m.
- (b) An enlargement, centre O, scale factor −1/2. — A single enlargement with a negative scale factor both changes the size (by the magnitude of the factor) and rotates the image 180° about the centre (giving the inverted orientation) in one transformation. Halving the size needs a magnitude of 1/2, and inverting needs a negative sign, so the scale factor is −1/2, centre O. 'Scale factor 1/2' gives the correct size but no inversion, since a positive scale factor keeps the same orientation. 'A 180° rotation with no change in size' gives the inversion but not the halving — K is described as smaller than J, so size must change too. 'Scale factor −2' inverts correctly but doubles the size instead of halving it.
- (b) −2 — The gradient of the original line is (6 − 2) ÷ (3 − 1) = 4 ÷ 2 = 2. Reflecting in the x-axis sends every y-coordinate to its negative, which flips the sign of the gradient: the image line has gradient −2. Translating by (2, 0) is a horizontal shift, which does not change the line's steepness or direction at all, so the gradient stays at −2. Assuming the gradient is unaffected by the reflection gives 2, the original gradient carried straight through. Thinking a reflection in the x-axis turns a gradient into its positive reciprocal gives 1/2. Combining that same wrong idea with the sign flip from the reflection gives −1/2. Only the sign flips, from the reflection, and translating never changes a gradient at all, so the answer is −2.
- (a) (8, 2) — Method: translating a point by a column vector means adding the vector's top number to the x-coordinate and its bottom number to the y-coordinate. Working: x-coordinate 2 + 6 = 8; y-coordinate 5 + (−3) = 2. Answer: B = (8, 2). A candidate who ignores the negative sign and adds 3 instead of −3 gets (8, 8). A candidate who translates in the reverse direction, subtracting the vector from A instead of adding it, gets (−4, 8). A candidate who swaps the vector's top and bottom numbers before adding gets (−1, 11).
- (b) 72 000 cm³ — Cross-sectional area = 1/2 × 40 × 30 = 600 cm². Volume = cross-sectional area × length = 600 × 120 = 72 000 cm³. (144 000 cm³ comes from forgetting the 1/2 in the triangle's area, using 40 × 30 as the cross-section; 36 000 cm³ comes from halving the correct volume again, as if the 1/2 applied a second time; 720 cm³ comes from adding the cross-sectional area and the length, 600 + 120, instead of multiplying them.)
- (a) 20 litres — Volume of water = length × width × depth of water = 40 × 25 × 20 = 20 000 cm³. Since 1000 cm³ = 1 litre, divide by 1000: 20 000 ÷ 1000 = 20 litres. A pupil who uses the full height of the tank, 30 cm, instead of the water depth, 20 cm, gets 40 × 25 × 30 = 30 000 cm³ = 30 litres. A pupil who forgets to convert cm³ to litres at all gives 20 000 litres. A pupil who divides by 1000 twice by mistake gets 20 000 ÷ 1000 ÷ 1000 = 0.02 litres. The correct volume of water is 20 litres.
- (d) 24 cm²; same way round as T — An enlargement scales area by the square of the scale factor, whatever its sign: area factor = (−2)² = 4, so the image's area is 6 × 4 = 24 cm². A negative scale factor is equivalent to an enlargement by the positive scale factor together with a rotation of 180°, so it does not create a mirror image — it is still a direct transformation, and combining it with a further rotation cannot create one either, since rotations never change a shape's orientation. Using the scale factor itself rather than its square gives area 6 × 2 = 12 cm², which is too small. Believing that a negative scale factor reflects the shape gives 'a mirror image of T' alongside the correct area of 24 cm², and combining both mistakes gives 12 cm² together with 'a mirror image of T'.
- (a) 80° — In triangle ABD, the three angles sum to 180°: angle BAD = 180° − 35° − 65° = 80°. ABCD is a cyclic quadrilateral, so the exterior angle at C, angle BCE, is equal to the interior angle at the opposite vertex, angle BAD: angle BCE = 80°. Adding the two given angles in triangle ABD instead of subtracting them from 180°, 35° + 65° = 100°, and then applying the exterior-angle rule correctly still gives the wrong angle BAD and so the wrong exterior angle, 100°. Halving the correct angle BAD, 80° ÷ 2 = 40°, confuses the exterior-angle rule with a different circle theorem in which one angle is half of another. Doubling it instead, 80° × 2 = 160°, makes the same kind of confusion in the other direction.
- (a) (9, −5) — Method: multiply every part of q by 2, then subtract the matching part from p. Working: 2q = (−4, 6); p − 2q gives top 5 − (−4) = 9 and bottom 1 − 6 = −5. Answer: p − 2q = (9, −5). A candidate who forgets to double q first, working out p − q instead, gets (7, −2). A candidate who doubles p instead of q, working out 2p − q, gets (12, −1). A candidate who adds 2q instead of subtracting it gets (1, 7).
Build your own mix at the worksheet builder.