Printable · GCSE Higher · ages 14-16
Geometry and measures worksheet — GCSE Higher
Fifteen questions across the geometry and measures statements at Higher tier. Choose the non-calculator filter to rehearse Paper 1, which counts for a third of the marks.
Answer key: Geometry and measures worksheet — GCSE Higher
MathsUKwww.geekhero.co.uk
- (a) 89.6° — Angle PQR is at vertex Q, so the side opposite it is PR = 13 cm. Using the cosine rule rearranged for an angle: cos(PQR) = (121 + 49 − 169) ÷ (2 × 11 × 7) = 1 ÷ 154 = 0.0065. Taking the inverse cosine, angle PQR = 89.6° (1 d.p.). Using PR as one of the enclosing sides instead of as the opposite side, finding angle P instead of angle Q, gives (121 + 169 − 49) ÷ (2 × 11 × 13) = 241 ÷ 286 = 0.8427, and angle = 32.6°. Swapping the sign inside the bracket, computing 169 − 121 − 49 instead, gives −1 ÷ 154 = −0.0065, and angle = 90.4°. Using PR in the denominator instead of QR gives (121 + 49 − 169) ÷ (2 × 11 × 13) = 1 ÷ 286 = 0.0035, and angle = 89.8°. Keep PR as the opposite side, QR and PQ as the enclosing sides, and angle PQR comes to 89.6°.
- (a) 0.1 m — Method: the sloping surface is the hypotenuse and the vertical rise is the side opposite the 30° angle, so rise = 4.8 × sin 30°; then compare that rise with the limit. Working: the exact value of sin 30° is one half, so the rise = 4.8 × 1/2 = 2.4 m. The limit is 2.5 m, and 2.5 − 2.4 = 0.1. Answer: the ramp is 0.1 m below the limit. Working out the rise and stopping there gives 2.4 m, which answers a question that was not asked. Dividing by sin 30° instead of multiplying gives 4.8 ÷ 0.5 = 9.6 and then 9.6 − 2.5 = 7.1 m. Treating sine as proportional to the angle, so that sin 30° is a third of sin 90°, gives 4.8 ÷ 3 = 1.6 and then 2.5 − 1.6 = 0.9 m.
- (a) 7.2 cm — The distance around the mat is the circumference, π × diameter = 3.14 × 20 = 62.8 cm. Yasmin started with 70 cm, so the ribbon left over is 70 − 62.8 = 7.2 cm. 62.8 cm is the circumference itself, the amount of ribbon used, not what is left over. 50 cm comes from subtracting the diameter instead of the circumference: 70 − 20 = 50. 20 cm is simply the diameter of the mat and involves no calculation with the ribbon length at all.
- (a) 17 cm — Convert the real distance to centimetres first: 3.4 km = 340 000 cm. Then divide by the scale factor, 20 000, since the map is 20 000 times smaller than real life: 340 000 ÷ 20 000 = 17, so the map distance is 17 cm. Choosing 1700 cm divides by 200 instead of 20 000, losing two zeros from the scale factor (340 000 ÷ 200 = 1700). Choosing 170 cm divides by 2 000 instead of 20 000, losing one zero from the scale factor (340 000 ÷ 2 000 = 170). Choosing 0.17 cm divides by 2 000 000 instead of 20 000, adding two extra zeros to the scale factor (340 000 ÷ 2 000 000 = 0.17).
- (a) 3 cm² — Area scale factor = (linear scale factor)² = (1/4)² = 1/16. Area of T = 48 × 1/16 = 3 cm². (12 cm² comes from multiplying by the linear scale factor 1/4 directly, without squaring it; 24 cm² comes from taking the square root of the scale factor instead of squaring it; 768 cm² comes from squaring the reciprocal of the scale factor, 4, instead of the scale factor itself.)
- (a) £4.20 — 350 g is 3.5 lots of 100 g, since 350 ÷ 100 = 3.5, so the cost is 3.5 × £1.20 = £4.20. Multiplying the mass in grams directly by the price, without dividing by 100 first, gives £420.00. Working out 100 ÷ 350 instead of 350 ÷ 100 inverts the ratio and gives about £0.34. Rounding 350 g down to 300 g gives 3 × £1.20 = £3.60.
- (c) 9 cm — The scale factor from triangle ABC to triangle PQR is PQ ÷ AB = 12 ÷ 8 = 1.5. So PR = AC × 1.5 = 6 × 1.5 = 9 cm. (4 cm comes from using the scale factor upside down, AB ÷ PQ; 10 cm comes from adding the difference between AB and PQ, 4 cm, to AC instead of scaling; 16 cm comes from multiplying PQ by the ratio AB : AC instead of scaling AC by the correct scale factor.)
- (d) sin 30°, tan 30°, cos 30° — sin 30° = 1/2 = 0.5, tan 30° = √3/3 ≈ 0.577 and cos 30° = √3/2 ≈ 0.866, so the correct order from smallest to largest is sin 30°, tan 30°, cos 30°. 'sin 30°, cos 30°, tan 30°' swaps the last two, wrongly putting cos 30° before tan 30°. 'cos 30°, tan 30°, sin 30°' is the correct list written backwards, from largest to smallest. 'tan 30°, sin 30°, cos 30°' wrongly swaps sin 30° and tan 30° at the start.
- (c) Translation by the vector (8, 0) — Method: reflecting twice in two parallel vertical lines is always equivalent to a single translation, at right angles to the lines, of twice the distance between them. Working: the two lines are 5 − 1 = 4 units apart, so the translation is 2 × 4 = 8 units in the positive x-direction. Answer: translation by the vector (8, 0). Using just the gap itself, without doubling it, gives (4, 0); translating in the negative x-direction, from the second line back towards the first, gives (−8, 0); and describing the combination as a single reflection in the line halfway between them, x = 3, confuses this combination with the effect of a single reflection — two reflections in parallel lines are always equivalent to a translation, never to another reflection. Always double the gap between the lines, and translate in the direction from the first line towards the second.
- (a) A square's diagonals are equal in length — A square has two pairs of parallel sides, four equal sides, and diagonals that are equal in length and cross at right angles. This tile's diagonals are not equal, so it is a rhombus that is not a square.
- (b) 31.0 cm² — Method: Area = 1/2ab sin C needs the angle BETWEEN the two given sides, so first find angle BAC using the angle sum of a triangle. Working: angle BAC = 180° − 65° − 65° = 50°, the angle between AB and AC; Area = 1/2 × 9 × 9 × sin 50° = 31.0 cm². Using the given base angle 65° in place of the included angle 50° gives 36.7 cm²; leaving out the 1/2 altogether gives 62.0 cm²; and using cos 50° instead of sin 50° gives 26.0 cm². The formula only works with the angle that sits between the two sides being multiplied — here that means finding the missing angle first.
- (a) 44.7 m — Method: the line joining the two tops is the hypotenuse of a right-angled triangle whose horizontal side is the gap between the masts and whose vertical side is the difference in their heights, so Pythagoras' theorem applies. Working: the difference in heights is 50 − 30 = 20 m, so d² = 40² + 20² = 1600 + 400 = 2000 and d = √2000 = 44.721…, which is 44.7 m to 1 decimal place. Answer: 44.7 m. The distractors: 34.6 m comes from subtracting the squares, √(40² − 20²), instead of adding them; 60.0 m comes from adding the two sides of the triangle, 40 + 20, rather than using Pythagoras' theorem; 50.0 m is the height of the taller mast, copied from the question in place of the distance asked for.
- (d) (−2, 6) — Method: add the top numbers of both vectors to the starting x-coordinate, and the bottom numbers of both vectors to the starting y-coordinate. Working: x-coordinate 2 + 3 + (−7) = −2; y-coordinate −1 + 5 + 2 = 6. Answer: (−2, 6). A candidate who only applies vector u and forgets v gets (5, 4). A candidate who only applies vector v and forgets u gets (−5, 1). A candidate who works out the combined vector u + v but forgets to add it to the starting point gets (−4, 7).
- (b) 8 : 27 — The heights are in the ratio 6 : 9, which simplifies to 2 : 3. For similar solids, volume scales with the cube of the length ratio, so the volume ratio is 2³ : 3³ = 8 : 27. 2 : 3 is only the simplified length ratio, without cubing. 4 : 9 comes from squaring instead of cubing — that's the rule for areas, not volumes. 27 : 8 has the correct cubed values but in the wrong order, giving the larger cone's volume first instead of the smaller.
- (c) 1/4 — A full turn at the centre of a circle is 360°, so a sector's fraction of the circle is its angle divided by 360°: 90 ÷ 360 = 1/4. 1/2 would be the fraction for a sector with an angle of 180°, not 90°. 3/4 is the fraction of the rest of the circle, the major sector left over from the 270° that is not part of this sector. 1/8 would be the fraction for a sector with an angle of 45°, half of 90°.
Build your own mix at the worksheet builder.