Printable · GCSE Higher · ages 14-16
Statistics worksheet — GCSE Higher
Fifteen questions across the statistics statements at Higher tier. Choose the non-calculator filter to rehearse Paper 1, which counts for a third of the marks.
Calculator
Statistics worksheet — GCSE Higher
MathsUKwww.geekhero.co.uk
- 1.A quality inspector weighs a random sample of 50 packets of crisps from one day's production and finds their mean mass is 32.4 g. The factory makes 20,000 packets that day. Work out an estimate for the total mass, in kg, of all the packets made that day.
- 2.A school has 1,000 pupils. A student wants to estimate how many of them walk to school, so she asks 8 pupils in her own class. She says her sample is large enough to give a reliable estimate for the whole school. Is she right? Give a reason for your answer.
- 3.A factory makes a batch of 4,000 circuit boards. It checks a random sample of 50 boards and finds that 4 are faulty. The factory will scrap the whole batch if the estimated number of faulty boards in the batch is more than 250. Should the factory scrap the batch?
- 4.A histogram shows the ages, in years, of 250 members of a running club. The bar for the class 10 ≤ age < 20 has a frequency density of 4.5 members per year, the bar for 20 ≤ age < 35 has a frequency density of 6 members per year, and the bar for 50 ≤ age < 70 has a frequency density of 2.75 members per year. Work out the frequency of the remaining class, 35 ≤ age < 50.
- 5.A scatter graph of taxi journeys in Bristol shows the distance, x miles, and the fare, y pounds. The line of best fit is y = 2x + 3.50. Work out the estimated fare for a journey of 6 miles, using the line of best fit.y = 2x + 3.5
- 6.A café in York counts the number of customers in each of the nine hours it is open on one day: 4, 4, 4, 11, 13, 15, 18, 22 and 25. The owner says that a typical hour has about 4 customers, because 4 is the mode. Is the owner right? Give a reason for your answer.
- 7.The masses, m kg, of 80 sacks of grain are summarised by these cumulative frequencies: m < 10, 6 sacks; m < 20, 22 sacks; m < 30, 58 sacks; m < 40, 74 sacks; m < 50, 80 sacks. Use interpolation to estimate the median mass.
- 8.A garden centre records the heights, in cm, of eleven seedlings. In order, the heights are 5, 9, x, 17, 20, 24, 28, 31, 35, 40, 44, where x is unknown. The interquartile range of the eleven heights is 19 cm. Work out the value of x.
- 9.In a histogram of the lengths, x cm, of some rods, the bar for 10 ≤ x < 30 has a frequency density of 3 per cm. The bar for 30 ≤ x < 45 is twice as tall as the bar for 10 ≤ x < 30. Work out the number of rods with a length in the class 30 ≤ x < 45.
- 10.For each of 30 fires in one county, the number of fire engines sent and the cost of the damage were recorded. The scatter graph of the data shows strong positive correlation. A newspaper prints the headline "Sending more fire engines causes more damage". Is the newspaper right? Give a reason for your answer.
- 11.Four pairs of variables are listed below. Write down the pair that you would expect to show negative correlation.
- 12.A scatter graph of the number of hours, x, that pupils revised against their test score, y, has the line of best fit y = 2.5x + 15. Amelia wants a score of at least 80. Work out the least whole number of hours of revision the line of best fit suggests she needs.y = 2.5x + 15
- 13.In a histogram of the heights, h cm, of 90 seedlings, the class 12 ≤ h < 18 contains 36 seedlings. Work out the frequency density for this class.
- 14.In a histogram of the distances, d metres, thrown by some athletes, the bar covering 20 ≤ d < 60 has a constant frequency density of 1.8 per metre. Estimate the number of throws of at least 20 metres but less than 35 metres.
- 15.A two-way table records whether each of 50 pupils in Year 10 or Year 11 at a school walks to school or is driven. 28 of the 50 pupils are in Year 10. In total, 22 of the 50 pupils walk to school. Of the Year 10 pupils, 15 walk to school. Work out how many Year 11 pupils are driven to school.
Answer key
- (d) 648 kg — Method: to estimate a total from a sample, multiply the sample's mean by the number of items in the whole population, then check the units the question asks for. Working: 32.4 g × 20,000 = 648,000 g. Converting to kilograms, 648,000 ÷ 1,000 = 648 kg. This is only an estimate, not an exact total, because it assumes every one of the 20,000 packets has exactly the sample mean mass, when in reality individual packets vary above and below it. Giving 1.62 kg multiplies the mean by 50, the SAMPLE size, instead of by 20,000, the number of packets actually made that day — this finds the total mass of the 50 sampled packets, not the day's production. Giving 32.4 kg treats the sample mean itself, in grams, as if it already were the day's total mass in kilograms, skipping the scaling up altogether. Giving 648,000 kg correctly scales the mean up to the whole day's production but never converts the answer from grams to kilograms, leaving it 1,000 times too large. Always scale a sample's mean up by the SIZE OF THE WHOLE POPULATION, and always finish by checking the units the question asks for.
- (c) No — 8 from one class is too small to represent the school. — Method: judge reliability by asking whether the sample is both large enough, and spread across the population, relative to what it is meant to represent. Working: 8 pupils is a tiny fraction of the school's 1,000 pupils, and all 8 come from a single class rather than a range of year groups, so the sample is both too small and too narrow to represent the whole school reliably. She is not right. Saying any sample size gives an equally reliable estimate ignores that reliability generally improves with a larger, more representative sample. Saying the method is unreliable because it was not done online is not a reason connected to sample size or representativeness at all. Saying 8 is reliable because it is more than half her class compares the sample to the wrong population — the school has 1,000 pupils, not one class. Always judge a sample's size against the population it is meant to represent, not against a smaller group within it.
- (c) Yes — with an estimate of 320, above the 250 limit. — Method: scale the sample proportion up to the whole batch to get an estimate, then compare that estimate with the 250 limit to reach a decision. Working: in the sample, 4 out of 50 boards are faulty, a proportion of 4 ÷ 50 = 0.08. Applying that proportion to the batch of 4,000 gives an estimate of 0.08 × 4000 = 320 faulty boards. Since 320 is more than 250, the factory should scrap the batch. Inverting the proportion, 50 ÷ 4 = 12.5, and treating that as a percentage of the batch, 12.5% × 4000 = 500, still gives 'yes' but from the wrong fraction, so it overstates the estimate. Comparing the raw number of faulty boards found in the sample, 4, directly with the 250 limit skips the scaling up to the batch altogether, and 4 is nowhere near 250, so that route wrongly says 'no'. Dividing the batch by the sample size, 4000 ÷ 50 = 80, finds how many samples of 50 fit into the batch but stops before multiplying by the 4 faulty boards found, so it also wrongly says 'no'. Always find the proportion in the sample first, scale it up to the whole batch, and only then compare the estimate with the limit given.
- (d) 60 — Method: on a histogram the frequency of a class is its frequency density × its class width, and the frequencies of all the classes add up to the total, so turn each labelled bar into a frequency and subtract their total from 250. Working: 10 ≤ age < 20 has width 20 − 10 = 10, so its frequency is 4.5 × 10 = 45; 20 ≤ age < 35 has width 35 − 20 = 15, so its frequency is 6 × 15 = 90; 50 ≤ age < 70 has width 70 − 50 = 20, so its frequency is 2.75 × 20 = 55. Those three come to 45 + 90 + 55 = 190, and the total is 250, so the missing frequency is 250 − 190 = 60. Answer: the class 35 ≤ age < 50 has 60 members. Watch what you do with the total and the three frequencies you have found: giving the total, 250, as the answer forgets that three bars have already accounted for some of the members; giving 190, the total of the other three classes, reports how many members are not in this class rather than how many are; and leaving one of the three out of the subtraction, for example 45 + 90 = 135 and 250 − 135 = 115, still owes the class at 50 ≤ age < 70 its 55 members.
- (d) £15.50 — 2 × 6 = 12, and 12 + 3.50 = 15.50, so the estimated fare is £15.50. Choosing £12.00 stops after 2 × 6 = 12 and forgets to add the £3.50. Choosing £19.00 adds the distance and the constant first and then multiplies: 6 + 3.50 = 9.50, and 9.50 × 2 = 19.00, applying the ×2 to the whole sum instead of only to the distance. Choosing £13.00 multiplies only the constant term by 2 instead of the distance: 2 × 3.50 = 7, and 7 + 6 = 13.00.
- (c) No, the mode here is the lowest value of the nine — Method: an average is meant to stand for the data as a whole, so test any proposed average by asking how many values it sits near. Working: the value 4 appears three times and every other count appears once, so 4 is indeed the mode. But those three hours are the quiet ones at the start of the day, and the other six counts run from 11 up to 25; putting the nine counts in order, the middle one is the fifth, which is 13. So the mode sits at the very bottom of the data, with six of the nine hours far above it. Answer: no, because the mode here is the lowest value of the nine, so it describes the quiet opening hours rather than a typical hour. The distractors: saying the mode can only be used when no value repeats reverses the definition, since a mode exists only because a value does repeat; saying the mode is the value that occurs most often is a correct definition, but being the commonest value does not make a value typical when it lies at one end of the data; saying the mode is the best average for any list of numbers ignores the fact that mean, median and mode each describe a population well in different circumstances.
- (d) 25 — Method: the median is estimated at position n ÷ 2 in the cumulative frequency table, then interpolated across the class it falls in: lower boundary, plus the fraction of the way through the class, times the class width. Working: there are 80 sacks, so the median sits at position 80 ÷ 2 = 40. Before the class 20 ≤ m < 30 the cumulative frequency is 22, and by the end of it, it is 58, so this class holds the 40th sack; its frequency is 58 − 22 = 36 and its width is 30 − 20 = 10. The extra distance needed into the class is 40 − 22 = 18, and 18 ÷ 36 × 10 = 5, so the median is 20 + 5 = 25. Answer: the estimated median mass is 25 kg. Watch which numbers the interpolation uses: reading off just the lower boundary of the median class, 20, ignores how far into that class the 40th sack actually falls; treating n ÷ 2 = 40 itself as the median mass mistakes a position in the list for a mass in kilograms; and using the target position, 40, as the extra distance into the class instead of subtracting the sacks already counted changes the calculation to 20 + 40 ÷ 36 × 10. That comes to 20 + 11.1 = 31.1, overshooting the class because it never subtracts the 22 sacks already counted before it.
- (d) 16 — Method: rearrange interquartile range = upper quartile − lower quartile to make the lower quartile the subject: lower quartile = upper quartile − interquartile range, then check the answer sits in the right place in the list. Working: there are 11 values, so 11 + 1 = 12; the upper quartile sits at position 3 × 12 ÷ 4 = 9, which is 35, and x sits at position 12 ÷ 4 = 3, which is the lower quartile. So x = 35 − 19 = 16, and 16 does sit between the 2nd value, 9, and the 4th value, 17, as it should. Answer: x = 16. Watch how you rearrange and where you count to: adding instead of subtracting, 35 + 19 = 54, treats the interquartile range as something added on rather than a gap taken away; subtracting in the wrong order, 19 − 35 = −16, finds the right two numbers but flips the sign; and counting to the 8th value instead of the 9th treats 31 as the upper quartile, giving 31 − 19 = 12, one position short of where the upper quartile actually sits.
- (c) 90 — Method: the height of a bar is its frequency density, so twice as tall means twice the frequency density — not twice the frequency, because the two classes have different widths. Then frequency = frequency density × class width. Working: the first bar has frequency density 3 per cm, so the second has frequency density 2 × 3 = 6 per cm; the class 30 ≤ x < 45 is 45 − 30 = 15 cm wide, so its frequency is 6 × 15 = 90. Answer: 90 rods. The distractors: 120 comes from doubling the first bar's frequency instead of its height — the first class holds 3 × 20 = 60 rods, and doubling that ignores the fact that the second class is narrower; 45 comes from using the first bar's frequency density, 3, for the second bar, 3 × 15, and so never using the information that it is twice as tall; 6 comes from stopping at the frequency density of the taller bar and quoting a height as though it were a count.
- (a) No, the size of the fire affects both of the quantities — Method: correlation says that two quantities change together; a claim that one of them produces the other is a further claim, and it needs evidence that a scatter graph on its own cannot give. Working: the graph does show strong positive correlation, so more engines did go with greater damage. But neither quantity was set by the researchers: both were decided by how large the fire was. A large blaze brings many appliances and also destroys a great deal, while a small one brings few and destroys little, so a third quantity is driving both of the recorded ones. Answer: no, because the size of the fire affects both of the quantities. The distractors: saying the correlation is negative contradicts the graph, which shows the two quantities rising together, and reaching the right verdict from a false reading of the data is not the reason the mark is for; saying that strong positive correlation shows one quantity causes the other is the assumption the question exists to test, and no strength of correlation can establish cause; saying the points lie close to the line of best fit describes how strong the correlation is, and strength and cause are different matters entirely.
- (a) Minutes a candle has burned and length remaining — As a candle burns for longer, less of it remains, so these two variables move in opposite directions as one increases — that is negative correlation. A pupil's shoe size generally increases as they get older, so age and shoe size show positive correlation, not negative, since both rise together. A football team's shirt colour is not a numerical quantity linked to how many matches it wins, so shirt colour and number of wins show no correlation at all. The number of letters in a pupil's name has no real connection to their ability in maths, so that pair also shows no correlation.
- (a) 26 — Method: a line of best fit lets one quantity be predicted from the other, so the score is substituted into the equation of the line and the resulting inequality is solved for the number of hours. Working: a score of at least 80 means 2.5x + 15 ≥ 80; taking 15 from both sides gives 2.5x ≥ 65, and dividing both sides by 2.5 gives x ≥ 26, so the least whole number of hours is 26. Checking, 2.5 × 26 + 15 = 80, which does reach the target. Answer: 26 hours — and this is only an estimate, because a line of best fit predicts a trend rather than an individual result, and a prediction made outside the range of hours the pupils actually revised for would be an extrapolation and less reliable still. The distractors: 27 comes from reaching 26 and then rounding up again, although 26 hours already gives a score of exactly 80; 32 comes from 80 ÷ 2.5, which ignores the 15 in the equation of the line; 38 comes from (80 + 15) ÷ 2.5, that is from adding the 15 instead of subtracting it when rearranging.
- (b) 6 — Method: frequency density = frequency ÷ class width. Working: the class 12 ≤ h < 18 has width 18 − 12 = 6, so frequency density = 36 ÷ 6 = 6. Answer: the frequency density is 6 seedlings per cm. Watch which numbers you use: taking the lower bound, 12, as the width instead of 18 − 12 = 6 gives 36 ÷ 12 = 3; dividing the total number of seedlings, 90, rather than this class's frequency, 36, by the width gives 90 ÷ 6 = 15, a density that belongs to no single class; and multiplying instead of dividing gives 36 × 6 = 216, far too large a density for so narrow a class.
- (c) 27 — Method: a frequency is the area of the part of the bar being asked about, so frequency = frequency density × the width of that part. Working: the part asked about runs from 20 to 35, so its width is 35 − 20 = 15 metres; the frequency density there is 1.8 per metre, so the estimate is 1.8 × 15 = 27. Answer: about 27 throws. The distractors: 72 comes from taking the whole bar, 1.8 × 40, and so counting every throw from 20 up to 60; 1.8 comes from reading the height of the bar as a frequency, when a height is a density and only an area is a count; 63 comes from using the upper value 35 as the width, 1.8 × 35, instead of the width 35 − 20.
- (a) 15 — Year 11 has 50 − 28 = 22 pupils in total. Of the 22 pupils who walk in total, 15 are in Year 10, so 22 − 15 = 7 Year 11 pupils walk. Subtracting that from the Year 11 total gives 22 − 7 = 15 Year 11 pupils who are driven. Choosing 28 takes the whole school's driven total, 50 − 22 = 28, and treats it as if it were Year 11's alone, without separating the year groups. Choosing 7 correctly finds how many Year 11 pupils walk but stops there, giving that figure instead of the number who are driven. Choosing 35 comes from 50 − 15, subtracting the Year 10 walkers from the whole school total rather than working within Year 11.
Build your own mix at the worksheet builder.