Printable · GCSE Higher · ages 14-16
Statistics worksheet — GCSE Higher
Fifteen questions across the statistics statements at Higher tier. Choose the non-calculator filter to rehearse Paper 1, which counts for a third of the marks.
Statistics worksheet — GCSE Higher
MathsUKwww.geekhero.co.uk
- 1.A factory makes a batch of 4,000 circuit boards. It checks a random sample of 50 boards and finds that 4 are faulty. The factory will scrap the whole batch if the estimated number of faulty boards in the batch is more than 250. Should the factory scrap the batch?
- 2.A scatter graph of taxi journeys in Bristol shows the distance, x miles, and the fare, y pounds. The line of best fit is y = 2x + 3.50. Work out the estimated fare for a journey of 6 miles, using the line of best fit.y = 2x + 3.5
- 3.A cumulative frequency graph for the diameters, d mm, of 320 ball bearings is plotted from these points (upper class boundary, cumulative frequency): (10, 30), (20, 90), (30, 190), (40, 280), (50, 320). Estimate the diameter below which 90% of the ball bearings measure.
- 4.A garden centre records the heights, in cm, of eleven seedlings. In order, the heights are 5, 9, x, 17, 20, 24, 28, 31, 35, 40, 44, where x is unknown. The interquartile range of the eleven heights is 19 cm. Work out the value of x.
- 5.The masses of eight school bags, in kilograms, are 3, 4, 4, 5, 6, 7, 8 and 11. Work out the median mass.
- 6.A study found that people who drink more coffee tend to concentrate better at work. A coffee company says that this shows that drinking coffee improves concentration. Give the reason why this conclusion cannot be drawn.
- 7.A call centre records the length, t seconds, of 100 calls: 0 ≤ t < 20, 15 calls; 20 ≤ t < 30, 24 calls; 30 ≤ t < 50, 40 calls; 50 ≤ t < 80, 21 calls. The manager's target is for a call to be finished in under 35 seconds. Estimate the number of calls that met the target.
- 8.Two classes sat the same maths test, both marked out of 100. Class A had a mean mark of 70 and a range of 30 marks. Class B had a mean mark of 70 and a range of 10 marks. Compare the marks of the two classes.
- 9.The 120 pupils in Year 11 at a school sat a maths test. Their marks m are grouped into classes of unequal width: 0 ≤ m < 40, 12 pupils; 40 ≤ m < 60, 24 pupils; 60 ≤ m < 70, 36 pupils; 70 ≤ m ≤ 100, 48 pupils. A histogram is drawn for these data. Work out the frequency density of the class 40 ≤ m < 60.
- 10.A gym draws a histogram of the times, t minutes, that its members spend on one machine. The bar for 0 ≤ t < 10 has a frequency density of 1.8 per minute, the bar for 10 ≤ t < 25 has a frequency density of 3.2 per minute, and the bar for 25 ≤ t < 55 has a frequency density of 0.9 per minute. Members who spend 10 minutes or more on the machine pay an extra charge. Work out the number of members who pay the extra charge.
- 11.A town council wants to find out about the eating habits of the people who live in the town. It asks only the members of a local sports club. Give a reason why this sample is biased.
- 12.A scatter graph of the number of ice creams sold at a seaside kiosk in Bournemouth and the number of sunburn cases treated at a nearby pharmacy, recorded on the same 30 days, shows strong positive correlation. Which statement about this correlation is correct?
- 13.In a scatter graph of the age, in years, and the wingspan, in cm, of 20 birds of the same species, all the points lie close to a rising line of best fit except one, which lies a long way below the line. That bird was later found to have a damaged wing. Give a reason why this point should not be used when drawing the line of best fit.
- 14.Priya travels to work by one of two routes and records her journey times, in minutes, over several weeks. Route 1 has a median of 34 minutes and an interquartile range of 22 minutes. Route 2 has a median of 41 minutes and an interquartile range of 6 minutes. Priya wants the more reliable route for getting to an important meeting on time. Which route should she choose, and why?
- 15.A box plot for the ages of 40 members of a gym is drawn from this five-number summary: minimum 15, lower quartile 22, median 29, upper quartile 38, maximum 61. Work out the interquartile range shown by this box plot.
Answer key
- (c) Yes — with an estimate of 320, above the 250 limit. — Method: scale the sample proportion up to the whole batch to get an estimate, then compare that estimate with the 250 limit to reach a decision. Working: in the sample, 4 out of 50 boards are faulty, a proportion of 4 ÷ 50 = 0.08. Applying that proportion to the batch of 4,000 gives an estimate of 0.08 × 4000 = 320 faulty boards. Since 320 is more than 250, the factory should scrap the batch. Inverting the proportion, 50 ÷ 4 = 12.5, and treating that as a percentage of the batch, 12.5% × 4000 = 500, still gives 'yes' but from the wrong fraction, so it overstates the estimate. Comparing the raw number of faulty boards found in the sample, 4, directly with the 250 limit skips the scaling up to the batch altogether, and 4 is nowhere near 250, so that route wrongly says 'no'. Dividing the batch by the sample size, 4000 ÷ 50 = 80, finds how many samples of 50 fit into the batch but stops before multiplying by the 4 faulty boards found, so it also wrongly says 'no'. Always find the proportion in the sample first, scale it up to the whole batch, and only then compare the estimate with the limit given.
- (d) £15.50 — 2 × 6 = 12, and 12 + 3.50 = 15.50, so the estimated fare is £15.50. Choosing £12.00 stops after 2 × 6 = 12 and forgets to add the £3.50. Choosing £19.00 adds the distance and the constant first and then multiplies: 6 + 3.50 = 9.50, and 9.50 × 2 = 19.00, applying the ×2 to the whole sum instead of only to the distance. Choosing £13.00 multiplies only the constant term by 2 instead of the distance: 2 × 3.50 = 7, and 7 + 6 = 13.00.
- (c) 42 — Method: find the target cumulative frequency, 90% of the total, locate the class it falls in from the plotted points, then interpolate: lower boundary, plus the extra distance needed into the class divided by the class's frequency, times its width. Working: 90% of 320 is 0.9 × 320 = 288. The plotted points show a cumulative frequency of 280 at d = 40 and 320 at d = 50, so the class 40 ≤ d < 50 has frequency 320 − 280 = 40 and width 50 − 40 = 10, and 288 falls inside it. The extra distance needed into the class is 288 − 280 = 8, and 8 ÷ 40 × 10 = 2, so the diameter is 40 + 2 = 42. Answer: the estimated diameter is 42 mm. Watch which point and which class the interpolation actually uses: reading off d = 40, the plotted point just below the target, instead of interpolating the extra 8 ball bearings into the next 10 mm, stops one step short of the true answer; finding the diameter below which only 10% lie instead of 90% gives a target of 0.1 × 320 = 32, which falls in the class 10 ≤ d < 20 — the extra distance into that class is 32 − 30 = 2, and 2 ÷ 60 × 10 = 0.3, so this route gives 10 + 0.3 = 10.3, the bottom decile rather than the top 90%; and interpolating within the class 30 ≤ d < 40 instead of 40 ≤ d < 50, as though 288 had not yet reached a cumulative frequency of 280, treats the extra distance as 288 − 190 = 98, and 98 ÷ 90 × 10 = 10.9, giving 30 + 10.9 = 40.9, one class too early.
- (d) 16 — Method: rearrange interquartile range = upper quartile − lower quartile to make the lower quartile the subject: lower quartile = upper quartile − interquartile range, then check the answer sits in the right place in the list. Working: there are 11 values, so 11 + 1 = 12; the upper quartile sits at position 3 × 12 ÷ 4 = 9, which is 35, and x sits at position 12 ÷ 4 = 3, which is the lower quartile. So x = 35 − 19 = 16, and 16 does sit between the 2nd value, 9, and the 4th value, 17, as it should. Answer: x = 16. Watch how you rearrange and where you count to: adding instead of subtracting, 35 + 19 = 54, treats the interquartile range as something added on rather than a gap taken away; subtracting in the wrong order, 19 − 35 = −16, finds the right two numbers but flips the sign; and counting to the 8th value instead of the 9th treats 31 as the upper quartile, giving 31 − 19 = 12, one position short of where the upper quartile actually sits.
- (b) 5.5 kg — Method: with an even number of values the median is the mean of the two middle values, taken once the data are in order of size. Working: the eight masses are already in order and 8 ÷ 2 = 4, so the middle pair are the 4th and 5th values, 5 kg and 6 kg; the median is (5 + 6) ÷ 2 = 5.5 kg. Answer: 5.5 kg. The distractors: 5 kg comes from reading the 4th value and stopping there instead of averaging the middle pair; 8 kg comes from working out the range, 11 − 3, which measures spread rather than centre; 4 kg comes from writing down the modal mass, the only value that occurs twice, instead of the median.
- (c) The data show a link only; a third factor may affect both — Method: a study of this kind measures two quantities and reports how they change together; deciding that one of them produces the other is a further claim, and it needs evidence that the measurements alone cannot give. Working: the study shows that more coffee goes with better concentration, which is a positive correlation; but a third factor that was never measured, such as how motivated someone is, could raise both the coffee drinking and the concentration, and the concentration could equally be what leads to the extra coffee. Answer: the data show a link only, because a third factor may be affecting both quantities, so no claim about cause can be made. The distractors: calling the conclusion safe because the correlation is positive treats the direction of a correlation as proof of cause, which no direction can give; calling it wrong because the correlation is negative misreads the direction of the relationship, since the study reports both quantities rising together; saying the two quantities are not linked denies the correlation the study actually found, when what fails is only the claim about cause.
- (a) 49 — Method: add the frequencies of the classes that lie wholly below 35 seconds, then use linear interpolation for the class that 35 cuts through, assuming the calls in that class are spread evenly across it. Working: below 30 seconds there are 15 + 24 = 39 calls; the value 35 lies in the class 30 ≤ t < 50, which is 20 seconds wide and holds 40 calls, and 35 is 35 − 30 = 5 seconds into it, so the estimated share is (5 ÷ 20) × 40 = 10 calls; the estimate is 39 + 10 = 49. Answer: about 49 calls met the target. The distractors: 79 comes from adding the whole of the class 30 ≤ t < 50, 39 + 40, and so counting calls of up to 50 seconds as being under 35; 39 comes from stopping at the class boundary 30 and ignoring the part class altogether; 69 comes from measuring the part of the class from 35 up to 50 instead of from 30 up to 35, giving (15 ÷ 20) × 40 = 30 and then 39 + 30.
- (a) The means are equal, and Class B's marks are the more consistent because its range is smaller. — Method: comparing two distributions needs two things — a measure of average and a measure of spread — and each must be put into the context of the question. Working: both classes have a mean mark of 70, so on average the two classes scored the same; the range measures spread, and Class A's range of 30 marks is three times Class B's range of 10 marks, so Class B's marks sit closely around the mean while Class A's are far more spread out. Answer: the means are equal, and Class B's marks are the more consistent because its range is smaller. The distractors: the reply crediting Class A with more consistency reverses the meaning of the range, treating a larger range as tighter data when a larger range means more spread; the reply that Class A's mean mark is higher compares the wrong pair of figures, reading the range of 30 as an average; the reply that Class B's mean mark is higher reads the spread correctly but its claim about the means is false, since both means are 70.
- (d) 1.2 pupils per mark — Method: on a histogram whose class intervals are not all the same width the height of a bar is not the frequency but the frequency density, found by dividing the frequency of the class by the width of that class, so that the area of the bar represents the frequency. Working: the class 40 ≤ m < 60 holds 24 pupils, and its width is 60 − 40 = 20 marks, so the frequency density is 24 ÷ 20 = 1.2. Answer: 1.2 pupils per mark. The distractors: 24 pupils per mark comes from plotting the frequency itself as the height, which is only correct when every class has the same width; 2.4 pupils per mark comes from dividing by 10, the width of the narrowest class, instead of by the width of this class; 0.2 pupils per mark comes from dividing by the 120 pupils in the year group, which gives the proportion of pupils in the class and not a frequency density.
- (c) 75 — Method: the number in a class is the area of its bar, frequency density × class width, so work out the frequency of each class that lies at or above 10 minutes and add them. Working: the class 10 ≤ t < 25 is 15 minutes wide with a frequency density of 3.2, giving 3.2 × 15 = 48 members; the class 25 ≤ t < 55 is 30 minutes wide with a frequency density of 0.9, giving 0.9 × 30 = 27 members; the total charged is 48 + 27 = 75. Answer: 75 members pay the extra charge. The distractors: 4.1 comes from adding the two frequency densities, 3.2 + 0.9, as though each height were a count; 93 comes from including the class 0 ≤ t < 10 as well, 1.8 × 10 = 18 added to 48 and 27, which charges every member; 27 comes from using only the class 25 ≤ t < 55 and forgetting that 10 ≤ t < 25 is also at or above 10 minutes.
- (c) Club members probably eat differently from most people — Method: a sample is biased when the group it is drawn from differs from the population in the very thing the survey is measuring, so compare the subgroup with the population on that quantity. Working: the survey measures eating habits, and people who join a sports club take more exercise than average and are known to eat differently from the town as a whole, so their replies pull the results away from the true picture for the town however many of them are asked. Answer: club members probably eat differently from most people. The distractors: the reply about the number of members treats bias as a question of size, but a large biased sample is still biased; the reply that the members were picked at random is false, since the council picked a club rather than picking residents, and it confuses bias with non-response; the reply that everyone asked lives in the town notes something true of the members but draws the false conclusion that the sample therefore covers the town, when a sample must reflect a population and not merely be taken from inside it.
- (c) Neither causes the other; sunshine links both. — Both ice cream sales and sunburn cases tend to rise on hot, sunny days, so the amount of sunshine is a third factor linked to both — neither variable causes the other. Saying ice cream sales cause the sunburn assumes a causal link in one direction that the correlation alone cannot establish. Saying sunburn cases cause the ice cream sales assumes the reverse causal link, which is no more justified. Saying a strong correlation always means causation is the general error this question is testing: correlation, however strong, does not by itself prove that one variable causes the other.
- (d) An outlier from the damaged wing, not the trend. — That bird's point lies a long way from the rising trend followed by every other bird, and its low wingspan is explained by the damaged wing rather than by its age — it is an outlier caused by an unusual factor, not part of the general relationship between age and wingspan, so it should not be used when drawing the line of best fit. Saying every point must be used ignores that an outlier caused by a separate, identifiable factor can rightly be set aside. Saying it shows no correlation ignores that the other 19 points do show a clear rising trend; one outlier does not remove that. Saying it proves the line is inaccurate confuses one unusual bird with a fault in the line itself, when the line correctly describes the trend followed by the rest of the data.
- (c) Route 2, because its interquartile range is smaller — Method: for a journey where turning up on time matters, what matters is not the typical (median) time but how predictable it is — a smaller interquartile range means the middle half of journeys cluster closer together. Working: Route 1's median, 34 minutes, is in fact lower than Route 2's, 41 minutes, so Route 1 is faster on average; but Route 1's interquartile range, 22 minutes, is far larger than Route 2's, 6 minutes, so Route 1's times are much less predictable. Answer: Priya should choose Route 2, because its interquartile range is smaller, even though it is slower on average. Watch which statistic answers the question actually asked: Route 1 does not have the smaller interquartile range, Route 2 does, so picking Route 1 for that reason misreads the table; Route 1's median genuinely is the lower one, but a lower median answers 'which is faster', not 'which is more reliable'; and Route 2's median is not the lower one, so that claim about Route 2 is simply false.
- (d) 16 — Method: on a box plot the interquartile range is the width of the box itself, upper quartile take away lower quartile. Working: the upper quartile is 38 and the lower quartile is 22, so 38 − 22 = 16. Answer: the interquartile range is 16 years. Watch which part of the box plot you are reading: the whole line from whisker to whisker gives the range, 61 − 15 = 46; the left half of the box alone gives median take away lower quartile, 29 − 22 = 7; and the right half of the box alone gives upper quartile take away median, 38 − 29 = 9 — neither half is the interquartile range on its own.
Build your own mix at the worksheet builder.