Printable · GCSE Foundation · ages 14-16
Plans and elevations worksheet — GCSE Foundation
Fifteen questions on "plans and elevations" — DfE statement G13. Print it, or print three versions so neighbours cannot copy by letter; the key gives the letter for each version.
Non-calculator
Answer key: Plans and elevations worksheet — GCSE Foundation
MathsUKwww.geekhero.co.uk
- (b) a rectangle — Lying on its side, the cylinder's curved surface touches the table along a straight line, and the two flat circular ends face sideways rather than up or down; viewed from directly above, the outline traced is a rectangle — as long as the cylinder and as wide as its diameter. "a circle" would be correct if the cylinder stood upright on one of its circular ends instead of lying on its side. "a triangle" belongs to a cone lying or standing so that it narrows to a point in that view, which a cylinder never does. "an oval" is a common guess from picturing the round ends, but from directly above those ends are edge-on and contribute to the rectangle's short sides, not a curved outline.
- (a) 24 — The display is 4 tins wide, 3 tins high and 2 tins deep, and every position in that block is filled, so the total number of tins is the product of all three measurements: 4 × 3 × 2 = 24. "12" comes from multiplying only the width and height shown in the front elevation (4 × 3), forgetting the depth entirely. "9" comes from adding the three measurements (4 + 3 + 2) instead of multiplying them. "6" comes from multiplying only the height and depth (3 × 2), forgetting the width shown by the front elevation.
- (a) 33 — Method: total crates = (number of floor positions that actually have crates on them) × (the stack height). Working: there are 4 × 3 = 12 floor positions in the whole arrangement, but one corner position is left empty, leaving 11 filled positions; each filled position is stacked 3 crates high, so 11 × 3 = 33. Answer: 33. The distractors: 36 comes from forgetting to remove the empty corner and using all 12 positions (12 × 3). 35 comes from removing only one crate for the empty corner instead of the full stack of 3 (36 − 1). 11 comes from counting the filled floor positions and stopping there, forgetting that each one carries a stack 3 crates high.
- (c) An L-shape — Method: to find the front elevation, trace the outline of the solid seen from directly in front. Working: the low, wide cuboid gives a wide rectangle across the bottom, and the taller, narrower cuboid sitting on one end adds a narrower rectangle rising above only that end of the base, so the outline steps up on one side only. Answer: an L-shape. The distractors: a rectangle comes from taking the outline of the box the whole solid would just fit inside, ignoring the step created by the taller block. A T-shape comes from placing the taller block in the middle of the base instead of at one end, so that the base would show on both sides of it. A parallelogram comes from copying a face as it is drawn in the sketch — the top of the taller block is drawn as a sloping parallelogram because the solid is drawn at an angle — instead of drawing the true outline seen looking straight at the front.
- (b) A triangular prism standing on its triangular end — Method: a rectangular elevation with no sloping sides means the solid keeps the same cross-section all the way from the bottom to the top; work out which solid, standing the right way up, has a triangular cross-section that stays that shape as you go higher. Working: a triangular prism standing upright on its triangular end has a triangle as its plan view, and because the cross-section is constant all the way up, both the front and side elevations are plain rectangles. Answer: a triangular prism standing on its triangular end. The distractors: a triangle-based pyramid standing on its triangular base does give a triangle as its plan view, but its cross-section shrinks towards the apex, so its front and side elevations come to a point and are triangles, not rectangles. A cuboid standing on a rectangular face is wrong because its plan view is a rectangle, not a triangle. A triangular prism lying on one of its rectangular faces is wrong because it is then the triangular end that faces the side, so its plan view is a rectangle and one of its elevations is a triangle.
- (b) 5 cm by 3 cm — The plan view looks straight down on the cuboid's footprint, so it shows the length (5 cm, left to right) and the depth (3 cm, front to back) — the two dimensions that do not involve height. "5 cm by 2 cm" repeats the front elevation's dimensions, pairing the length with the height instead of the depth. "3 cm by 2 cm" repeats the side elevation's dimensions, again pairing the depth with the height rather than with the length. "5 cm by 5 cm" comes from mistakenly assuming the plan must be a square, pairing the length with itself instead of with the depth.
- (c) 5 — The front elevation shows one square for every cube visible from the front, column by column: the left-hand column is 2 cubes high, so it contributes 2 squares; the middle column is 2 cubes high, so it contributes 2 more; the right-hand column is 1 cube high, so it contributes 1. The total is 2 + 2 + 1 = 5 squares. "6" comes from drawing a full 3 by 2 rectangle, treating every column as if it reached the greatest height. "4" comes from losing a square from one of the two tall columns, counting 2 + 1 + 1. "3" comes from counting one square per column — the width of the solid — and ignoring the heights altogether.
- (a) a cone — A cone, viewed from directly above, shows its circular base as a circle; viewed from the front, its curved surface narrows to a point at the apex, giving a triangle outline — so a circle plan with a triangle elevation identifies a cone. "a cylinder" has a circular plan too, but its front elevation is a rectangle, not a triangle, since its sides run straight up rather than narrowing to a point. "a sphere" gives a circle from every direction, plan and every elevation alike, not a triangle from the front. "a square-based pyramid" gives a triangle from the front, but its plan view is a square, not a circle.
- (a) 3 squares — Method: the plan view shows only the floor positions that have at least one cube standing on them; height does not add extra squares to the plan. Working: the base row occupies three floor positions in a line. The two extra cubes stand on top of two of those same three positions, so they do not create any new floor position. Answer: 3 squares. The distractors: 5 squares comes from adding the total number of cubes used (3 + 2 = 5) instead of counting distinct floor positions. 2 squares comes from counting only the raised two-cube section and ignoring the single cube at the other end of the row. 4 squares comes from counting one of the shared positions twice.
- (b) 28 — Method: total bricks = (number of squares in the footprint) × (the height of the wall in bricks). Working: the footprint has the row of 5 squares plus the 2 squares in the arm that stands out from the middle of that row, and they do not overlap, giving 5 + 2 = 7 squares; multiplying by the height of 4 bricks gives 7 × 4 = 28. Answer: 28. The distractors: 20 comes from using only the row of 5 and ignoring the arm (5 × 4). 24 comes from treating the bottom square of the arm as if it were one of the row's own squares, so the arm is counted as adding only 1 new square instead of 2 (5 + 1 = 6, then 6 × 4). 32 comes from counting the square of the row directly below the arm a second time as part of the arm (5 + 3 = 8, then 8 × 4).
- (b) Triangle — Method: the front elevation is the outline you see looking straight at the solid's front face. Working: this solid's front face is one of its two identical triangular ends, so looking directly at the front shows exactly that triangular outline. Answer: triangle. The distractors: rectangle comes from picturing the side view instead of the front view — looking along the ridge of the prism, the sloping roof faces project as a rectangle. Trapezium comes from misreading the two sloping roof faces as if together they formed a single four-sided shape. Pentagon comes from tracing round the outline of the whole sketch as it is drawn on the page, which is a five-sided shape, instead of drawing only the view seen looking straight at the front of the solid.
- (b) 23 — If every position were filled to the full height of 3, the total would be 2 × 4 × 3 = 24 crates. One corner position has only 2 crates instead of 3, one crate short of full height there, so the actual total is 24 − 1 = 23. "24" comes from using the full height everywhere and forgetting the one incomplete corner. "22" comes from removing 2 crates for the incomplete corner instead of the 1 that is actually missing (3 − 2 = 1, not 2). "21" comes from removing all 3 crates at that corner, as though the position were completely empty rather than 2 crates short.
- (d) a rectangle — The shed is a prism, so its two triangular ends are identical and parallel, a fixed distance apart along the shed's length; the floor they stand on is therefore bounded by the base of one triangle, the base of the other, and the two straight edges joining them — a rectangle. Looking straight down, the sloping roof projects onto that same rectangle rather than outside it, so the plan view is a plain rectangle, as long as the shed and as wide as its gable end. "a triangle" is the shape of the END wall, seen from the front or back, not from above. "a triangle with a rectangle attached" wrongly combines a side-elevation feature with the plan — the plan does not show the triangular end wall at all, since looking down hides it completely. "two triangles joined at their bases" describes neither the plan nor any single elevation of this shed.
- (a) A cuboid — Method: work out which solid has flat faces only, no curved surfaces and no point where edges meet, since only that gives rectangles for all three views. Working: a solid whose plan, front elevation and side elevation are all rectangles has three pairs of flat rectangular faces meeting at right angles — that is a cuboid. Answer: a cuboid. The distractors: a cylinder is wrong because its plan view (from above) is a circle, not a rectangle. A cone is wrong because its plan view is a circle and its front and side elevations are triangles. A square-based pyramid is wrong because its front and side elevations come to a point at the apex, giving triangles rather than rectangles, even though its plan view could be a square.
- (d) A rectangle — Method: to find the plan view, work out the outline traced when looking straight down onto the solid from directly above, not the outline shown in the angled sketch. Working: this solid has two identical flat round ends joined by one curved surface, and it is lying on its side rather than standing upright; viewed from above, the curved surface gives two straight edges running the full length of the solid, the width of the round ends apart, and each flat round end — seen edge-on from directly above — also becomes a straight edge of that same width, with no curve remaining. Four straight edges, with opposite sides equal and meeting at right angles, form a rectangle. Answer: a rectangle. The distractors: a circle comes from picturing the solid as if it were standing upright on one of its flat ends, giving the plan of an upright version instead of working out the plan of the solid as it actually lies. An oval comes from copying the foreshortened shape of a round end as it is drawn in the angled sketch, instead of working out the true shape seen from directly above, which has no such foreshortening. A rectangle with rounded ends comes from carrying the curve of the round ends over into the plan view, when in fact a flat round end viewed edge-on from directly above shows no curve at all, only a straight edge.
Build your own mix at the worksheet builder.