Printable · GCSE Higher · ages 14-16
Gradients and areas under graphs worksheet — GCSE Higher
Fifteen questions on "gradients and areas under graphs" — DfE statement A15. Print it, or print three versions so neighbours cannot copy by letter; the key gives the letter for each version.
Higher only
Gradients and areas under graphs worksheet — GCSE Higher
MathsUKwww.geekhero.co.uk
- 1.A tap fills a tank at a varying rate. A graph shows the rate of flow, in litres per minute, against time, in minutes. What does the area under this graph represent?
- 2.The tangent to a curve at the point (6, 1) has gradient −3. Work out the y-coordinate of the point where this tangent crosses the y-axis.
- 3.The table shows the velocity, in m/s, of a train at various times, in seconds: 0 at t = 0, 20 at t = 4, 35 at t = 10, 27 at t = 14. Assuming the velocity changes at a constant rate between each pair of readings, estimate the distance the train travels between t = 0 and t = 12, using the trapezium rule.
- 4.The trapezium rule is used to estimate the area under a curve between x = 2 and x = 6. The curve is concave up (it curves upwards, like the inside of a bowl) throughout this interval. Which statement about the estimate is correct?
- 5.A distance-time graph is a straight line from (0, 0) to (4, 100), where time is in hours and distance is in kilometres. Work out the gradient of the line.
- 6.A car's journey is represented by a velocity-time graph. The total distance travelled, found from the area under the graph, is 350 metres, and the total time for the journey is 25 seconds. Work out the car's average speed for the whole journey, in m/s.
- 7.A cyclist's velocity increases from 3 m/s to 11 m/s over 5 seconds, at a constant rate. Work out the cyclist's acceleration, in m/s².
- 8.The table shows the speed, in m/s, of a cyclist at times, in seconds, 1 second apart: 0 at t = 0, 7 at t = 1, 12 at t = 2, 15 at t = 3, 16 at t = 4, 14 at t = 5, 9 at t = 6. Using the trapezium rule with strip width 1 second, estimate the distance the cyclist travels between t = 2 and t = 5 only.
- 9.A tram travels between two stops. Its velocity-time graph consists of straight line segments joining the points (0, 0), (5, 20), (12, 20), (16, 4) and (20, 4), where time is in seconds and velocity is in m/s. Work out the average speed of the tram over the whole 20 seconds. Give your answer to 1 decimal place.
- 10.A car's speed, in m/s, during a journey is: 0 at t = 0 s, 8 at t = 4 s, and 8 (constant) from t = 4 s to t = 10 s, increasing at a constant rate between t = 0 and t = 4. Estimate the total distance the car travels, using the areas of a triangle and a rectangle.
- 11.A cyclist's speed rises from rest to a maximum — quickly at first, then more and more slowly — so her speed-time graph is a curve that is concave down (its gradient decreases as time goes on). A trapezium estimate is made for the distance travelled during this phase, using two points on the curve. Is the trapezium estimate an overestimate or an underestimate of the true distance, and why?
- 12.A bath is filled with water; the graph of volume (litres) against time (minutes) is a curve, since the flow rate changes. The tangent to the curve at t = 10 minutes passes through the points (8, 130) and (12, 190), and the volume in the bath at t = 10 minutes is 160 litres. Use the gradient of this tangent to estimate the volume in the bath 5 minutes after t = 10 minutes.
- 13.A cup of tea cools after being made. Its temperature-time graph is a curve. Three tangents are drawn on the graph: at t = 2 minutes the tangent has gradient −8; at t = 10 minutes the tangent has gradient −3; at t = 20 minutes the tangent has gradient −0.5. Which of these statements about the tea's cooling is correct?
- 14.The table shows the rate at which water flows from a tank, in litres per minute, over a 6-minute period: 12 at t = 0 min, 12 at t = 2 min, 3 at t = 5 min, and 0 at t = 6 min. Between t = 0 and t = 2 the rate is constant. Between t = 2 and t = 5, and between t = 5 and t = 6, the rate decreases at a constant rate in each section. Estimate the total volume of water that has flowed out, using the areas of a rectangle and two trapeziums.
- 15.On a distance-time graph, a horizontal line segment shows a period when the graph's gradient is 0. What does this tell you about the journey during that time?
Answer key
- (b) The total volume of water, in litres, that has flowed in. — On a rate-time graph, the y-axis is in litres per minute and the x-axis is in minutes; multiplying a rate by a time gives litres per minute × minutes = litres, a total volume. So the area under the graph represents the total volume of water that has flowed in. Thinking the area itself represents the rate, rather than what the rate accumulates to, gives the wrong claim about the average rate of flow. Confusing the area with the gradient of the graph — which measures how the rate is changing — gives the wrong claim about litres per minute squared. Ignoring the flow-rate axis and focusing only on the time axis gives the wrong claim that the area is simply the total time.
- (b) 19 — A line through (x₁, y₁) with gradient m has equation y − y₁ = m(x − x₁). Substituting (6, 1) and m = −3: y − 1 = −3(x − 6), so y = −3x + 18 + 1, which simplifies to y = −3x + 19; at x = 0 this gives 19. Making a sign error when distributing, writing −3(x − 6) as −3x − 18 instead of −3x + 18, gives the wrong line y = −3x − 17, so −17 at x = 0. Forgetting to add the y₁ = 1 at the end, using y = −3(x − 6) alone, gives 18 at x = 0. Substituting the y-coordinate into the gradient term instead of using x, working out 1 + (−3 × 1), gives −2.
- (a) 271 m — The reading at t = 12 isn't in the table, so it must be interpolated between t = 10 (35 m/s) and t = 14 (27 m/s): the velocity falls by 8 m/s over the 4-second gap, so over 2 seconds it falls by 4 m/s, giving 35 − 4 = 31 m/s. The trapezium rule then uses three strips of unequal width, 4, 6 and 2 seconds, with areas of 40, 165 and 66: 40 + 165 + 66 = 271 m. Writing 267 m comes from skipping the interpolation and using the table's t = 14 reading, 27, directly as the height at t = 12. Writing 282 m comes from treating all three strips as though they were 4 seconds wide, instead of using the true gaps of 4, 6 and 2 seconds between the readings. Writing 275 m comes from using the t = 10 reading, 35, at both ends of the final strip, instead of interpolating a new value at t = 12.
- (a) Overestimates — trapezium edges lie above the curve. — For a concave-up curve, each chord connecting two points on the curve lies ABOVE the curve between those points, because the curve bends away from the chord underneath it. The trapezium rule uses these chords as the top edges of each trapezium, so the trapeziums cover a larger region than the true area under the curve — the estimate is an overestimate. Saying it underestimates because the edges lie below the curve gets the direction backwards: for a concave-up curve the edges lie above, not below. Saying it overestimates 'because more strips always increase it' gives the right verdict for the wrong reason — using MORE, narrower strips makes a trapezium estimate more accurate and brings it closer to the true area, it does not simply increase the total. Saying the estimate is exact ignores that straight edges cannot follow a curved line perfectly; there is always a gap between the chord and the curve on a bend, which is exactly what makes the rule an estimate rather than an exact calculation.
- (a) 25 — Gradient = change in y ÷ change in x = (100 − 0) ÷ (4 − 0) = 100 ÷ 4 = 25. Dividing time by distance instead of distance by time gives 0.04; multiplying the two values instead of dividing gives 400; stopping at the change in distance, 100, forgets to divide by the change in time.
- (b) 14 m/s — Average speed for a whole journey is total distance divided by total time: 350 ÷ 25 = 14 m/s. Multiplying the distance and time instead of dividing gives 350 × 25 = 8750 m/s. Adding the distance and time instead of dividing gives 350 + 25 = 375 m/s. Inverting the division, working out time divided by distance, gives 25 ÷ 350, which rounds to 0.07 m/s.
- (b) 1.6 m/s² — Acceleration is the change in velocity divided by the time taken: (11 − 3) ÷ 5 = 8 ÷ 5 = 1.6 m/s². Forgetting to subtract the initial velocity and dividing the final velocity by the time instead gives 11 ÷ 5 = 2.2 m/s². Inverting the fraction, dividing the time by the change in velocity, gives 5 ÷ 8 = 0.625 m/s². Finding the change in velocity, 8 m/s, but stopping without dividing by the time gives 8 m/s².
- (d) 44 m — The trapezium rule between t = 2 and t = 5 uses only the speeds at t = 2, 3, 4 and 5 — 12, 15, 16 and 14 — with three strips of width 1: adding the first and last readings and twice the sum of the middle readings gives 12 + 14 + 2 × (15 + 16) = 88, and half of that is 44 m. Writing 68.5 m comes from applying the trapezium rule to the whole table, from t = 0 to t = 6, instead of restricting it to the interval t = 2 to t = 5 that the question asks for. Writing 28.5 m comes from forgetting to double the two middle readings, 15 and 16, in the trapezium rule formula. Writing 39 m comes from averaging only the first and last speeds in the interval, 12 and 14, and multiplying by the 3-second interval, ignoring the readings at t = 3 and t = 4 in between.
- (b) 12.7 m/s — Find the total distance from the area under the graph, then divide by the total time. Break the graph into its four straight sections: a triangle from (0, 0) to (5, 20), where 5 × 20 = 100 gives an area of 50 m when halved; a rectangle from (5, 20) to (12, 20), area 7 × 20 = 140 m; a trapezium from (12, 20) to (16, 4), where (20 + 4) × 4 = 96 gives an area of 48 m when halved; and a rectangle from (16, 4) to (20, 4), area 4 × 4 = 16 m — a total distance of 50 + 140 + 48 + 16 = 254 m. Dividing by the 20 seconds gives an average speed of 254 ÷ 20 = 12.7 m/s. Writing 15.1 m/s comes from forgetting to halve the trapezium area for the third section, using 96 instead of 48: a total of 302 m, and 302 ÷ 20 = 15.1 m/s. Writing 11.9 m/s comes from leaving out the final section, from (16, 4) to (20, 4), entirely: a total of 238 m, and 238 ÷ 20 = 11.9 m/s. Writing 12.1 m/s comes from dividing the correct total distance by 21 instead of 20 — a fencepost slip, counting the whole seconds from t = 0 to t = 20 inclusive as 21 seconds of travel rather than reading the journey as a duration of 20 seconds: 254 ÷ 21 = 12.1 m/s (1 d.p.).
- (c) 64 m — The distance travelled is the area under the speed-time graph. From t = 0 to t = 4, the shape is a triangle with base 4 and height 8, area 1/2 × 4 × 8 = 16. From t = 4 to t = 10, the shape is a rectangle with base 6 and height 8, area 6 × 8 = 48. Total distance: 16 + 48 = 64 m. Treating the whole 10 seconds as a single trapezium with parallel sides 0 and 8 and width 10, instead of splitting it into the triangle and rectangle, gives 40 m. Ignoring the acceleration phase completely and assuming the car travels at a constant 8 m/s for all 10 seconds gives 8 × 10 = 80 m. Misreading the second interval as running from t = 4 to t = 8 instead of t = 4 to t = 10 gives a rectangle area of 4 × 8 = 32, plus the correct triangle of 16, totalling 48 m.
- (a) Underestimate: the chord lies below the curve — For a curve that is concave down (bending downward), the straight line joining any two points on the curve lies BELOW the curve. The trapezium's top edge is this straight line, so the trapezium's area is smaller than the true area under the curve — the trapezium rule UNDERESTIMATES the distance in this case. This is because a curve whose gradient keeps decreasing bends away from any chord joining two of its points, dropping the chord below every point of the curve in between. The reverse, a chord lying above the curve, is the rule for a concave-up curve, not this one — check which way the curve bends before deciding. The trapezium rule does not always overestimate or underestimate, and it is not exact except when the graph really is a straight line.
- (b) 235 litres — The flow rate at t = 10 is the gradient of the tangent: change in volume ÷ change in time = (190 − 130) ÷ (12 − 8) = 60 ÷ 4 = 15 litres per minute. Treating this rate as roughly constant for a short interval, the volume 5 minutes after t = 10 is estimated as 160 + 5 × 15 = 235 litres. Using the tangent's own point spacing — 2 minutes, from t = 10 to t = 12 — instead of the 5 minutes actually asked for gives 160 + 2 × 15 = 190, which is just the volume already given at one of the tangent's own points, not an answer to the question asked. Multiplying the gradient by the time WITHOUT adding the starting volume, 5 × 15 = 75, forgets that a rate estimates a CHANGE, which must be added to the starting volume, not given as the answer on its own. Subtracting instead of adding, 160 − 5 × 15 = 85, extrapolates backward in time rather than forward.
- (c) Fastest at t = 2 min — steepest gradient. — The rate of cooling is given by the size (magnitude) of the gradient, ignoring its sign — the steeper the tangent, the faster the temperature is changing. Of −8, −3 and −0.5, the gradient −8 has the greatest magnitude, so the tea is cooling fastest at t = 2 minutes. 'Fastest at t = 20 min — largest gradient' confuses the signed value with the size of the rate: −0.5 is the largest NUMBER of the three, but it's the smallest in magnitude, meaning the tea is barely cooling at all by then. 'Cools at the same rate throughout' ignores that the three gradients are different sizes, not just all negative. 'Fastest at t = 10 min — the middle reading' isn't a mathematical reason at all — the gradients themselves have to be compared, not their position in the list.
- (a) 48 litres — Split the area into three sections. The rectangle (t = 0 to 2) has area 2 × 12 = 24. The first trapezium (t = 2 to 5, parallel sides 12 and 3, width 3) has area 1/2 × (12 + 3) × 3 = 22.5. The second trapezium (t = 5 to 6, parallel sides 3 and 0, width 1) has area 1/2 × (3 + 0) × 1 = 1.5. Total volume: 24 + 22.5 + 1.5 = 48 litres. Forgetting the rectangle and adding only the two trapeziums gives 22.5 + 1.5 = 24 litres. Using a single trapezium across the whole 6 minutes, with parallel sides 12 and 0, ignoring that the first 2 minutes are constant, gives 1/2 × (12 + 0) × 6 = 36 litres. Correctly finding the rectangle and the first trapezium but forgetting to halve the second trapezium, using (3 + 0) × 1 = 3 instead of 1.5, gives 24 + 22.5 + 3 = 49.5 litres.
- (c) The object was stationary (not moving) — On a distance-time graph, the gradient at any point represents the speed at that point. A gradient of 0 means distance is not changing over time, so the object is stationary. A straight, sloped line (not flat) shows constant nonzero speed; a curve bending one way shows acceleration or deceleration; a flat section is not a maximum speed — it is no speed at all. Read the shape of the graph, not just how steep it looks.
Build your own mix at the worksheet builder.