Printable · GCSE Higher · ages 14-16
Gradients and areas under graphs worksheet — GCSE Higher
Fifteen questions on "gradients and areas under graphs" — DfE statement A15. Print it, or print three versions so neighbours cannot copy by letter; the key gives the letter for each version.
Higher only
Gradients and areas under graphs worksheet — GCSE Higher
MathsUKwww.geekhero.co.uk
- 1.The tangent to a curve at the point (6, 1) has gradient −3. Work out the y-coordinate of the point where this tangent crosses the y-axis.
- 2.A cyclist accelerates uniformly from rest to 6 m/s in 4 seconds, travels at a constant 6 m/s for 10 seconds, then decelerates uniformly to rest in 3 seconds. Work out the total distance the cyclist travels.
- 3.A car's journey is represented by a velocity-time graph. The total distance travelled, found from the area under the graph, is 350 metres, and the total time for the journey is 25 seconds. Work out the car's average speed for the whole journey, in m/s.
- 4.A cyclist's velocity increases from 3 m/s to 11 m/s over 5 seconds, at a constant rate. Work out the cyclist's acceleration, in m/s².
- 5.A car's velocity–time graph is a straight line from (0 s, 4 m/s) rising to (6 s, V m/s), followed by a straight line falling from (6 s, V m/s) to (9 s, 0 m/s). The gradient of the second line is −8 m/s². Work out the total distance travelled between t = 0 and t = 9 seconds.
- 6.A bath is filled with water; the graph of volume (litres) against time (minutes) is a curve, since the flow rate changes. The tangent to the curve at t = 10 minutes passes through the points (8, 130) and (12, 190), and the volume in the bath at t = 10 minutes is 160 litres. Use the gradient of this tangent to estimate the volume in the bath 5 minutes after t = 10 minutes.
- 7.The table shows the speed, in m/s, of a cyclist at times, in seconds, 1 second apart: 0 at t = 0, 7 at t = 1, 12 at t = 2, 15 at t = 3, 16 at t = 4, 14 at t = 5, 9 at t = 6. Using the trapezium rule with strip width 1 second, estimate the distance the cyclist travels between t = 2 and t = 5 only.
- 8.The tangent to a curve at the point where x = 4 passes through the points (2, 5) and (6, 21). Use these two points to estimate the gradient of the curve at x = 4.
- 9.A cup of tea cools after being made. Its temperature-time graph is a curve. Three tangents are drawn on the graph: at t = 2 minutes the tangent has gradient −8; at t = 10 minutes the tangent has gradient −3; at t = 20 minutes the tangent has gradient −0.5. Which of these statements about the tea's cooling is correct?
- 10.The table shows the rate at which water flows from a tank, in litres per minute, over a 6-minute period: 12 at t = 0 min, 12 at t = 2 min, 3 at t = 5 min, and 0 at t = 6 min. Between t = 0 and t = 2 the rate is constant. Between t = 2 and t = 5, and between t = 5 and t = 6, the rate decreases at a constant rate in each section. Estimate the total volume of water that has flowed out, using the areas of a rectangle and two trapeziums.
- 11.A company's cost, in £, for producing x items is shown on a graph. The tangent to the curve at x = 50 passes through (30, 400) and (70, 800). Interpret the gradient of this tangent in the context of the company's costs.
- 12.A speed-time graph shows a constant speed of 15 m/s for 20 seconds. Work out the distance travelled, using the area under the graph.
- 13.The table shows the height, in metres, of a firework rocket at various times, in seconds, during its flight: 40 at t = 2, 54 at t = 3, and 60 at t = 4. Use the chord between t = 2 and t = 4 to estimate the gradient of the height-time graph at t = 3, stating the correct units.
- 14.The curve y = x² − 3x. Use the chord between x = 1 and x = 4 to estimate the gradient of the curve at x = 2.5.y = x² − 3x
- 15.The area under a speed-time graph between t = 0 and t = 6 seconds is estimated using three strips of equal width, using the speeds, in m/s, at t = 0, 2, 4 and 6: 0, 5, 9 and 12. Using the trapezium rule with these three trapezia, estimate the distance travelled.
Answer key
- (b) 19 — A line through (x₁, y₁) with gradient m has equation y − y₁ = m(x − x₁). Substituting (6, 1) and m = −3: y − 1 = −3(x − 6), so y = −3x + 18 + 1, which simplifies to y = −3x + 19; at x = 0 this gives 19. Making a sign error when distributing, writing −3(x − 6) as −3x − 18 instead of −3x + 18, gives the wrong line y = −3x − 17, so −17 at x = 0. Forgetting to add the y₁ = 1 at the end, using y = −3(x − 6) alone, gives 18 at x = 0. Substituting the y-coordinate into the gradient term instead of using x, working out 1 + (−3 × 1), gives −2.
- (c) 81 m — Split the velocity-time graph into its three phases. The accelerating phase (0 to 4 s) is a triangle: 1/2 × 4 × 6 = 12. The constant phase (4 s at 6 m/s, for 10 s) is a rectangle: 10 × 6 = 60. The decelerating phase (3 s) is a triangle: 1/2 × 3 × 6 = 9. Total distance: 12 + 60 + 9 = 81 m. Forgetting the final decelerating phase entirely and adding only the first two areas gives 12 + 60 = 72 m. Treating all three phases as rectangles, forgetting to halve either triangular phase, gives 4 × 6 + 10 × 6 + 3 × 6 = 102 m. Halving only the deceleration triangle correctly but treating the acceleration phase as a rectangle too gives 4 × 6 + 60 + 9 = 93 m.
- (b) 14 m/s — Average speed for a whole journey is total distance divided by total time: 350 ÷ 25 = 14 m/s. Multiplying the distance and time instead of dividing gives 350 × 25 = 8750 m/s. Adding the distance and time instead of dividing gives 350 + 25 = 375 m/s. Inverting the division, working out time divided by distance, gives 25 ÷ 350, which rounds to 0.07 m/s.
- (b) 1.6 m/s² — Acceleration is the change in velocity divided by the time taken: (11 − 3) ÷ 5 = 8 ÷ 5 = 1.6 m/s². Forgetting to subtract the initial velocity and dividing the final velocity by the time instead gives 11 ÷ 5 = 2.2 m/s². Inverting the fraction, dividing the time by the change in velocity, gives 5 ÷ 8 = 0.625 m/s². Finding the change in velocity, 8 m/s, but stopping without dividing by the time gives 8 m/s².
- (a) 120 m — The gradient of the second line is (0 − V)/(9 − 6) = −V/3, and this equals −8, so V = 24. The distance from t = 0 to t = 6 is the area of a trapezium with parallel sides 4 and 24 and width 6: 1/2 × (4 + 24) × 6 = 84. The distance from t = 6 to t = 9 is the area of a triangle with base 3 and height 24: 1/2 × 3 × 24 = 36. The total distance is 84 + 36 = 120 m. Using V = 8, treating the gradient's number as the missing velocity itself rather than solving −V/3 = −8 for V, gives a trapezium area of 1/2 × (4 + 8) × 6 = 36 and a triangle area of 1/2 × 3 × 8 = 12, a total of 48 m. Leaving out the 1/2 in the trapezium formula, (4 + 24) × 6 = 168, plus the correct triangle of 36, gives 204 m. Using the full 6 seconds as the triangle's base instead of the 3 seconds the second line actually lasts, 1/2 × 6 × 24 = 72, plus the correct trapezium of 84, gives 156 m.
- (b) 235 litres — The flow rate at t = 10 is the gradient of the tangent: change in volume ÷ change in time = (190 − 130) ÷ (12 − 8) = 60 ÷ 4 = 15 litres per minute. Treating this rate as roughly constant for a short interval, the volume 5 minutes after t = 10 is estimated as 160 + 5 × 15 = 235 litres. Using the tangent's own point spacing — 2 minutes, from t = 10 to t = 12 — instead of the 5 minutes actually asked for gives 160 + 2 × 15 = 190, which is just the volume already given at one of the tangent's own points, not an answer to the question asked. Multiplying the gradient by the time WITHOUT adding the starting volume, 5 × 15 = 75, forgets that a rate estimates a CHANGE, which must be added to the starting volume, not given as the answer on its own. Subtracting instead of adding, 160 − 5 × 15 = 85, extrapolates backward in time rather than forward.
- (d) 44 m — The trapezium rule between t = 2 and t = 5 uses only the speeds at t = 2, 3, 4 and 5 — 12, 15, 16 and 14 — with three strips of width 1: adding the first and last readings and twice the sum of the middle readings gives 12 + 14 + 2 × (15 + 16) = 88, and half of that is 44 m. Writing 68.5 m comes from applying the trapezium rule to the whole table, from t = 0 to t = 6, instead of restricting it to the interval t = 2 to t = 5 that the question asks for. Writing 28.5 m comes from forgetting to double the two middle readings, 15 and 16, in the trapezium rule formula. Writing 39 m comes from averaging only the first and last speeds in the interval, 12 and 14, and multiplying by the 3-second interval, ignoring the readings at t = 3 and t = 4 in between.
- (a) 4 — The gradient of a straight line through two points is the change in y divided by the change in x. Change in y = 21 − 5 = 16. Change in x = 6 − 2 = 4. Gradient = 16 ÷ 4 = 4. Dividing x by y instead of y by x gives 0.25; forgetting to divide by the change in x at all leaves 16; dividing by only one of the two x-coordinates, 16 ÷ 2 = 8, uses the wrong denominator.
- (c) Fastest at t = 2 min — steepest gradient. — The rate of cooling is given by the size (magnitude) of the gradient, ignoring its sign — the steeper the tangent, the faster the temperature is changing. Of −8, −3 and −0.5, the gradient −8 has the greatest magnitude, so the tea is cooling fastest at t = 2 minutes. 'Fastest at t = 20 min — largest gradient' confuses the signed value with the size of the rate: −0.5 is the largest NUMBER of the three, but it's the smallest in magnitude, meaning the tea is barely cooling at all by then. 'Cools at the same rate throughout' ignores that the three gradients are different sizes, not just all negative. 'Fastest at t = 10 min — the middle reading' isn't a mathematical reason at all — the gradients themselves have to be compared, not their position in the list.
- (a) 48 litres — Split the area into three sections. The rectangle (t = 0 to 2) has area 2 × 12 = 24. The first trapezium (t = 2 to 5, parallel sides 12 and 3, width 3) has area 1/2 × (12 + 3) × 3 = 22.5. The second trapezium (t = 5 to 6, parallel sides 3 and 0, width 1) has area 1/2 × (3 + 0) × 1 = 1.5. Total volume: 24 + 22.5 + 1.5 = 48 litres. Forgetting the rectangle and adding only the two trapeziums gives 22.5 + 1.5 = 24 litres. Using a single trapezium across the whole 6 minutes, with parallel sides 12 and 0, ignoring that the first 2 minutes are constant, gives 1/2 × (12 + 0) × 6 = 36 litres. Correctly finding the rectangle and the first trapezium but forgetting to halve the second trapezium, using (3 + 0) × 1 = 3 instead of 1.5, gives 24 + 22.5 + 3 = 49.5 litres.
- (d) The cost increases by about £10 per extra item — Gradient = change in cost ÷ change in items = (800 − 400) ÷ (70 − 30) = 400 ÷ 40 = 10. The units of the gradient are £ per item, so the cost is increasing by about £10 for every extra item produced, near x = 50. Subtracting in the wrong order, (400 − 800) ÷ (70 − 30) = −10, gives the right size but the wrong sign — check which point comes first each time. Leaving out the division by 40 gives £400 per item; dividing the wrong way round, 40 ÷ 400 = 0.1, gives £0.10 per item.
- (d) 300 m — For a constant speed, the speed-time graph is a horizontal line, and the area underneath is a rectangle: distance = speed × time = 15 × 20 = 300 m. Adding the two numbers instead of multiplying gives 35 m; dividing instead of multiplying gives 1.33 m; halving the product, as you would for a triangle, gives 7.5 m — but this section of the graph is a rectangle, not a triangle, so there is no halving to do.
- (c) 10 m/s — A symmetric chord gradient uses the two points either side of t = 3: (2, 40) and (4, 60). The gradient is the change in height divided by the change in time: (60 − 40) ÷ (4 − 2) = 20 ÷ 2 = 10 m/s. Using only the values either side of one gap, (2, 40) and (3, 54), instead of the full symmetric chord, gives (54 − 40) ÷ (3 − 2) = 14 m/s. Getting the correct number but dropping the time unit, leaving only metres, gives 10 m. Dividing time by height instead of height by time inverts the calculation to (4 − 2) ÷ (60 − 40) = 0.1 s/m.
- (c) 2 — At x = 1, y = 1² − 3(1) = 1 − 3 = −2. At x = 4, y = 4² − 3(4) = 16 − 12 = 4. Gradient of the chord = change in y ÷ change in x = (4 − (−2)) ÷ (4 − 1) = 6 ÷ 3 = 2. Writing down the change in y, 6, and stopping there without dividing by the change in x gives 6. Losing the negative sign on y = −2 at x = 1 and treating it as +2 gives (4 − 2) ÷ (4 − 1) = 2 ÷ 3 = 2/3. Dividing the wrong way round, change in x ÷ change in y, gives (4 − 1) ÷ (4 − (−2)) = 3 ÷ 6 = 1/2.
- (d) 40 m — Each trapezium has width 2. Its area is width × the average of its two heights. Strip 1: average of 0 and 5 is 2.5, so area = 2 × 2.5 = 5. Strip 2: average of 5 and 9 is 7, so area = 2 × 7 = 14. Strip 3: average of 9 and 12 is 10.5, so area = 2 × 10.5 = 21. Total distance = 5 + 14 + 21 = 40 m. Leaving out the division by 2 in the averaging step doubles every strip, giving 80 m instead of 40 m. Using only the LEFT height of each strip as a rectangle, 0 × 2 + 5 × 2 + 9 × 2 = 28, or only the RIGHT height, 5 × 2 + 9 × 2 + 12 × 2 = 52, both ignore that the graph curves between the two ends of each strip — always average the two heights of a trapezium, never use just one of them.
Build your own mix at the worksheet builder.