Geometry and measures worksheet — GCSE Higher

1.A carpenter cuts two triangular metal brackets for a shelf. Bracket P has sides of 12 cm, 16 cm and 20 cm. Bracket Q has sides of 16 cm, 20 cm and 12 cm, listed in a different order. Before fitting them as a matching pair, the carpenter wants to check they are exactly the same shape and size. Which of the following correctly justifies this?

2.Lines JK and LM are parallel. A straight line crosses JK at point P and crosses LM at point Q. Angle KPQ = 118°. Angle KPQ and angle MQP are co-interior (allied) angles. Work out angle MQP.

3.A skateboard ramp is designed so that a straight rail RT is tangent to a circular curve at the point T, and TC is a chord of the curve from T to another point C on the curve. A second rail continues straight through T on the other side, so that the two rails together form a straight line, and the angle between that second rail and the chord TC is 109°. A support point D is placed on the curve, on the major arc TC. Work out the size of angle TDC, the angle subtended by the chord TC at D.

4.A square-based pyramid is cut by a flat plane parallel to its base, partway up between the base and the apex. What shape is the cross-section?

5.A scale drawing shows a room that is 5 cm wide. The real room is 15 m wide. Write the scale of the drawing in the form 1 : n.

6.A kitchen scale is marked in equal divisions of 20 g. The pointer rests three divisions past the 400 g mark. Work out the reading on the scale.

7.A cuboid has length 3 cm, width 4 cm and height 12 cm. Work out the length of the diagonal that runs from one corner of the cuboid to the opposite corner.

8.In triangle ABC, angle ABC = 90° and angle BAC = 30°. The hypotenuse AC = 12 cm. Work out the exact length of AB.

9.A triangular solar panel has two edges of length 1.8 m and 1.3 m, with an angle of 72° between them. Manufacturing the panel costs £85 per square metre. Work out the total manufacturing cost. Give your answer to the nearest penny.

10.A drone flies from its base in three stages, each stage measured in metres east and north as a column vector. Stage 1 is the column vector with top number 30 and bottom number 40. Stage 2 is the column vector with top number −10 and bottom number 20. Stage 3 is the column vector with top number 15 and bottom number −5. Work out the column vector that would take the drone in a single straight flight back to its base from where it ends up.

11.A dog is tied by a lead 4 m long to a fixed ring on a straight garden wall. The wall extends much further than the lead can reach in both directions, and the dog cannot cross through it. Describe the region the dog can reach.

12.A circular table mat has diameter 20 cm. Yasmin has a 70 cm length of ribbon and sews it around the edge of the mat with no overlap. Using π = 3.14, work out how much ribbon is left over after going around the mat once.

13.A roof has two triangular sections, P and Q. Section P has a sloping edge of 3.6 m and a base edge of 2.4 m, with an angle of 70° between them. Section Q has a sloping edge of 3.6 m and a base edge of 2.4 m, with an angle of 70° between them, arranged the same way round. A roofer wants to cut identical triangular felt panels for both sections without measuring Section Q separately. Which condition confirms that the two sections are congruent?

14.In triangle OAB, OA = a and OB = b. P is the point on OA such that OP = (1/3)a, and Q is the point on OB such that OQ = (1/3)b. Express the vector PQ in terms of a and b.

15.A photograph is 10 cm wide and 15 cm tall. It is enlarged to make a similar poster that is 40 cm wide. The poster costs £0.80 per centimetre of its height to print, based on its full height. Work out the cost of printing the poster.